HYDRAULIC CRAWLER DRILLING RIG cod. Data: Date: Compilato da: Filled in by: RESP.PROGHU Approvato da: Approved by: DIR.TEC/F
I/I INDICE - MAIN TECHNICAL... 1 - HYDRAULIC CIRCUIT (Engine power 147 kw)... 3 - TECHNICAL MAST... 4 - OPTIONS... 7 - ACCESSORIES... 8 - TRANSPORT CONFIGURATIONS... 9 - WORKING CONFIGURATIONS... 10 - MAGAZINE M1... 18 - REVISIONE / REVISION... 19
1/19 MAIN TECHNICAL UNDERCARRIAGE Overall width of undercarriage 2400 mm 7,9 ft Width of track shoes 500 mm 19,7 in Length of crawlers 2860 mm 9,4 ft Travelling speed 2,4 km/h 1,5 mph Max. Gradeability 20 (36.4% ) (*) 20 (36.4% ) (*) Max traction force 140 kn 31,500 lbs Hydraulic track oscillation +15 ; -15 +15 ; -15 Ground pressure 6,7 N/cm² 9,7 PSI Fuel tank capacity 270 l 72 gal Hydraulic oil tank capacity 520 l 137 gal (*) Max. slope without use of accessories (winch for operating the drilling on the slope) according to EN 791 CLAMPS Type CB2 M2Z / M2SZ M4 / M4S Diameter 68 / 254 mm 2,7 / 10 in 40 / 254 mm 1,6 / 10 in 60 / 305 mm 2,4 / 12 in Clamping force 196 kn 44,100 lbs 145 kn 32,600 lbs 250 kn 56,200 lbs ROTARY HEAD Type HG11 HG12 HG19 Max. torque 10,55 knm 7,760 lbs ft 12,70 knm 9,350 lbs ft 19,00 knm 14,000 lbs ft Max. speed 170 rpm 102 rpm 102 rpm Type HG24 T1200-6V T1500 P130 Max. torque 26,40 knm 19,470 lbs ft 11,95 knm 8,800 lbs ft 15,21 knm 11,200 lbs ft Max. speed 58 rpm 530 rpm 110 rpm Type T2000 P200 T2500 Max. torque 16,29 knm 12,000 lbs ft 20,00 knm 14,720 lbs ft Max. speed 220 rpm 220 rpm DRIFTERS Type HB35A HB40A HB50A Max. torque 6,29 knm 4,630 lbs ft 9,70 knm 7,150 lbs ft 14,06 knm 10,350 lbs ft Max. speed 220 rpm 110 rpm 195 rpm Impact energy 590 340 Nm 590 340 Nm 835 420 Nm Type HH40/12 Max. torque 12,70 knm 9,350 lbs ft Max. speed 102 rpm Impact energy 590 340 Nm DOUBLE HEAD DRILLING UNIT Front rotary head Rear rotary head Recommended HG19 HG11, HG12, HB35A, HH40/12 Recommended HG24 HG11, HG12, HB35A, HH40/12
2/19 OVERALL DIMENSIONS AND WEIGTH Length with mast in horizzontal position (DM200 6400/5000) c.a. 7360 mm (DM300 6350/4000) c.a. 7400 mm Heigth with mast in horizzontal position 2800 mm 9,2 ft 2800 mm 9,2 ft Width 2400 mm 7,9 ft 2400 mm 7,9 ft Weigth 14800 Kg * - 32,630 lbs * 15900 Kg * - 35,050 lbs * * depending on mounted equipment DIESEL ENGINE Model Type Rated power (ISO 14396) Engine cooling system Specific fuel consumption Emission certification DEUTZ TCD 2012 L06 2V Turbocharged 147 kw (200 HP) at 2300 rpm Water circulation 236 g/kwh EPA/COM III
3/19 HYDRAULIC CIRCUIT (Engine power 147 kw) For rotary / rotary or rotary / rotary-percussive PUMPS P1 P2 P3 P4+P5 P6 Double variable displacement axial piston pump with load sensing control X X Fixed displacement gear pump X X X Delivery l/min 218 218 170 2 x 38 75 Working Pressure bar 250 250 Power setting kw 60 60 SIMULTANEOUS OPERATIONS CONTROL TYPE FUNCTIONS FLOWS (Litres/min) A B C D E Hydraulic Travel 150 150 300 Hydraulic Rotation of Rotary Head I (ROD) 200 200 200 200 50 Hydraulic Rotation of Rotary Head II (CASING) 200 150 50 Hydraulic Drifter < 100 < 100 < 100 Hydraulic Feed (Normal speed) 50 50 50 50 Hydraulic Feed (Hight speed) 150 50 200 Hydraulic Mast set-up 40 Hydraulic Lateral slide of head I 40 Hydraulic Relative shift of Heads I and II 40 Hydraulic Clamps 40 Hydraulic Stabilizers 40 Hydraulic Service winch and hydraulic jib 40 Hydraulic Heat exchanger 170 Hydraulic Cooler fan motors 76 Electric Water pump 75 (*) Electric Foam pump 15 Max engine speed 2300 rpm The standard version of the hydraulic system includes 2 main, variable capacity piston pumps: P1, P2 with Load Sensing control regulators. NB. Simultaneous operations may vary according to the equipment mounted on the machine. (*) Depending on water pump type
4/19 TECHNICAL MAST MAST DM200 Box structure 200 x 200 x 6,3 mm with guides (7,87 x 7,87 x 0,25 in) Extraction/crowd force 100 / 100 kn 22,500 / 22,500 lbs Fast speed Crowd / Extraction 55 / 55 m/min 180 / 180 ft/min Slow speed Crowd / Extraction 13 / 13 m/min 43 / 43 ft/min Rotary head side movement 575 mm 22.6 in ROTARY DRIFTER HB50
5/19 ROTARY / ROTARY-PERCUSSIVE (WITH SEPARATE TROLLEY) MAST DM200 (jet grouting application) Box structure 200 x 200 x 6,3 mm with guides (7,87 x 7,87 x 0,25 in) Extraction/crowd force 100 / 50 kn 22,500 / 11,250 lbs Fast speed Crowd / Extraction 100 / 50 m/min 328 / 164 ft/min Slow speed Crowd / Extraction 24 / 12 m/min 80 / 40 ft/min Rotary head side movement 575 mm 22.6 in ROTARY
6/19 MAST DM300 Box structure 300 x 200 x 8 mm with guides (11,81 x 7,87 x 0,32 in) Extraction/crowd force 200 / 100 kn 45,000 / 22,500 lbs Fast speed Crowd / Extraction 50 / 25 m/min 164 / 82 ft/min Slow speed Crowd / Extraction 12 / 6 m/min 40 / 20 ft/min Rotary head side movement 500 mm 19.6 in ROTARY / ROTARY WITH REAR SWIVEL AND DOUBLE LATERAL MOVEMENT Only for vertical drilling
7/19 LATERAL MOVEMENT OPTIONS WINCH Winch type A2 Nominal Line pull 20 kn - 4500 lbs CAT HEAD WITH SWINGING PULLEY FLUSHING PUMP TYPE GAMMA 202 Pressure 60 bar - ( 870 psi ) Delivery 200 l/min - ( 53 gal/min )
8/19 ACCESSORIES OILER 24 l WELDING MACHINE GENERATOR 5kW COMPRESSOR ADDITIONAL TRAKING LEVERS ON CONTROL PANEL PUMP NG 530 L WASHER / FOAM PUMP FOAM TANK Capacity 150 l ( 36.6 gal ) HOSE REEL FOR WASHING WITH 10 m HOSE REAR STABILIZERS MAGAZINE M1
9/19 TRANSPORT CONFIGURATIONS
10/19 WORKING CONFIGURATIONS
11/19
12/19
13/19
14/19
15/19
16/19
17/19 JET GROUTING APPLICATION
18/19 MAGAZINE M1
19/19 REVISIONE / REVISION EMISSIONE / ISSUE : 17/11/2005 REVISIONE / REVISION 01 : 12/12/2005 Pag.2 - Aggiornamento dati tecnici - Updating technical data REVISIONE / REVISION 02 : - Aggionamento caratteristiche tecniche e disegni - Updating all the technical characteristics and drawings