ACQUA e FUOCO TWO ELEMENTS, ONE SOLUTION
di tanto in tanto arriva un prodotto rivoluzionario che cambia tutto. every once in a while a revolutionary product comes along that changes everything. (Steve Jobs, 2007)
COS E AQUAFIRE? WHAT IS AQUAFIRE? 5 PERCHE AQUAFIRE? WHY AQUAFIRE? 6 DOVE USARE AQUAFIRE? WHERE AQUAFIRE? 8 COME SI INSTALLA AQUAFIRE? HOW INSTALL AQUAFIRE? 14 SISTEMA AQUAFIRE vs. SISTEMA TRADIZIONALE AQUAFIRE SYSTEM VS. TRADITIONAL SYSTEM 18 SCHEDE TECNICHE TECHNICAL DATA SHEET 24 APPLICAZIONI VERTICALI VERTICAL APPLICATIONS 35 APPLICAZIONI ORIZZONTALI HORIZONTAL APPLICATIONS 43 Ottobre 2013 Verificare che la presente revisione del manuale coincida con quella pubblicata sul nostro sito prima della messa in opera del prodotto Verify this manual revision coincides with that published on our website before the installation of the product 3
COS E AQUAFIRE? WHAT IS AQUAFIRE? Aquafire è una lastra in cemento alleggerito fibrorinforzato resistente all acqua e al fuoco. Aquafire è un sistema di costruzione semplice e veloce. Aquafire è sicura e garantita dalla marchiatura CE. Aquafire is a fibre-reinforced lightweight cement board water and fire resistant. Aquafire is a simple and easy dry construction system. Aquafire is safe and guaranteed by CE mark. AQUAFIRE Product code / Codice Prodotto F03150030 Length (mm) Lunghezza (mm) 2000 Width (mm) Larghezza (mm) 1200 Lot Number / Production Date N Lotto / Data Produzione 17/04/2013 Euroclass / Euroclasse: A1 12 A flat sheet of Fiber-reinforced lightweight concrete indoor and outdoor Lastra in cemento alleggerito fibrorinforzato per ambienti interni ed esterni NT Thickness (mm) Spessore (mm) 12,5 N Pezzi pallet Pieces/Packaging 50 CLASSE 1 CATEGORIA A Bifire s.r.l. Sede Legale via Carducci 8 - Milano - 20123 (MI) Sede Operativa via Lavoratori dell Autobianchi 1 - Desio - 20832 (MB) Telefono +39 0362-364570 - Telefax +39 0362-334134 Internet - E-mail bifire@bifire.it Partita IVA 03645510961 Capitale Sociale 600.000,00 i.v. Registro Imprese Monza Brianza n 03645510961 - N REA CCIAA MI 1964336 5
PERCHE AQUAFIRE? WHY AQUAFIRE? PIU RESISTENTE ALL ACQUA MORE WATER RESISTANT PIU RESISTENTE AL FUOCO, CERTIFICATA FINO A 240 MINUTI MORE FIRE RESISTANT, CERTIFIED UP TO 240 MINUTI PIU FACILE DA TAGLIARE, COME IL CARTONGESSO EASIER TO CUT, LIKE PLASTERBOARD 6
PERCHE AQUAFIRE? WHY AQUAFIRE? PIU FACILE DA AVVITARE, COME IL CARTONGESSO EASIER TO SCREW, LIKE PLASTERBOARD PIU LEGGERA -17% LIGHTER -17% PIU ISOLANTE l=0,096 W/m K MORE INSULATION l=0,096 W/m K PIU FLESSIBILE R min =90cm MORE FLEXIBLE R min =90cm 7
DOVE USARE AQUAFIRE? WHERE AQUAFIRE? Ambienti a rischio umidità Humidity risk ambient Centri benessere Spa Piscine Swimming polls Superfici a rischio infiltrazioni Infiltration risk surface 8
DOVE USARE AQUAFIRE? WHERE AQUAFIRE? Garage Box Scaffalature in ambienti umidi Bookcase in humid ambients Cantine Cellars / Winery Lavanderie Laundry 9
DOVE USARE AQUAFIRE? WHERE AQUAFIRE? Saune Saunas Vasche Baths Bagni turchi Turkish baths Vani doccia Showers 10
DOVE USARE AQUAFIRE? WHERE AQUAFIRE? Piani per cucine Plans for kitchens Pavimenti tradizionali Floors Supporti per piastrelle Tiles support Pavimenti a secco Dry floors 11
DOVE USARE AQUAFIRE? WHERE AQUAFIRE? Rivestimento di caminetti Fireplaces coating Compartimentazione antincendio Fireproof partitions Rivestimenti zone alte temperature Coating in areas with high temperatures Supporto impianti fotovoltaici Support for photovoltaic 12
DOVE USARE AQUAFIRE? WHERE AQUAFIRE? Tettoie Roofs Superfici curve Curved surface Verande Verandas Facciate esterne External facade 13
COME SI INSTALLA AQUAFIRE? HOW INSTALL AQUAFIRE? In esterno Outdoor Lastra Aquafire Vite Aquafire Star Nastro Aquafire Rasante Aquafire Rete Aquafire Rasante Aquafire Finitura muraria 14
COME SI INSTALLA AQUAFIRE? HOW INSTALL AQUAFIRE? In interno Indoor Lastra Aquafire Vite Aquafire Star Nastro Aquafire Finish Lisciatura con Finish 15
COME SI INSTALLA AQUAFIRE? HOW INSTALL AQUAFIRE? In esterno 1. Le lastre andranno installate su orditura metallica idonea a seconda trattasi di parete, controparete, soffitto o facciata ventilata. 2. Si raccomanda l utilizzo di profili a norma UNI EN dello spessore di 10/10mm. La zincatura dovrà essere maggiore od uguale a 200 gr/mq. 3. Disporre i montanti ad un passo non maggiore di 40cm. 4. Le lastre Aquafire dovranno essere rigorosamente posate perpendicolarmente alle orditure metalliche, con il lato taglio a vista, i giunti dovranno essere sfalsati come nelle normali applicazioni dei rivestimenti a secco. 5. Fra una lastra e l altra lasciare c.a. 3-4mm. 6. Si consiglia di non tenere il bordo della lastra a diretto contatto con le basi di appoggio per impedire l eventuale risalita di umidità per capillarità, sali od impurità delle basi di appoggio. 7. Fissare le lastre Aquafire alla struttura metallica con le Viti Aquafire Star avvitando sul lato taglio a passo 20cm (15cm per le applicazioni in orizzontale); dal bordo lastra si indica una distanza di c.a. 15mm per sfruttare al meglio il contatto della lastra alla ampia superficie della testa della vite. 8. Spalmare uno strato di Rasante Aquafire sui giunti longitudinali e trasversali, largo 150mm. 9. Annegare la rete per giunti Nastro Aquafire da 75mm nel rasante appena posato; 10. Passato il tempo di asciugatura di 12 ore, spalmare uno strato di Rasante Aquafire sull intera superficie della lastra con frattazzo dentato in acciaio. 11. Annegare la Rete Aquafire nel rasante appena posato, avendo cura di nasconderla completamente, lavorando con il lato liscio del frattazzo dentato. 12. A questo punto lo spessore finale della rasatura deve essere di 3mm. 13. Completare la superficie con una finitura muraria tipo intonachino acrilico, acril-silossanico o silossanico. In interno 1. Le lastre andranno installate su orditura metallica idonea a seconda trattasi di parete, controparete o soffitto. 2. Si raccomanda l utilizzo di profili a norma UNI EN dello spessore di 6/10mm. 3. Disporre i montanti ad un passo non maggiore di 60cm. 4. Le lastre Aquafire dovranno essere installate alle orditure metalliche con il lato taglio a vista. 5. Fra una lastra e l altra lasciare c.a. 3-4mm. 6. Si consiglia di non tenere il bordo della lastra a diretto contatto con le basi di appoggio per impedire l eventuale risalita di umidità per capillarità, sali od impurità delle basi di appoggio. 7. Fissare le lastre Aquafire alla struttura metallica con le Viti Aquafire Star avvitando sul lato taglio a passo 25cm (15cm per le applicazioni in orizzontale); dal bordo lastra si indica una distanza di c.a. 15mm per sfruttare al meglio il contatto della lastra alla ampia superficie della testa della vite. 8. Spalmare uno strato di Finish sui giunti longitudinali e trasversali, largo 100mm. 9. Annegare la rete per giunti Nastro Aquafire da 75mm nel rasante appena posato; 10. Dopo 24 ore, lisciare la parete con Finish in un unica mano. 11. A questo punto la parete è pronta per la tinteggiatura. Superfici curve Per creare superfici curve si possono utilizzare le lastre intere Aquafire fino ad un raggio minimo di 2 metri. Per raggi inferiori e fino a 90cm utilizzare lastre di larghezza pari a 30cm, avvitandole al supporto con viti Aquafire star a passo 10cm. 16
COME SI INSTALLA AQUAFIRE? HOW INSTALL AQUAFIRE? Outdoor 1. The boards will be installed on suitable metallic frames depending on whether the installation is on walls, linings walls, ceiling or ventilated façade. 2. we recommend using metallic profiles in compliance with the UNI EN standard with 10/10mm thickness.the galvanizing must be greater than or equal to 200 gr/m 2. 3. Arrange the frames one step no greater than 40cm. 4. Aquafire boards must be installed perpendicular to the metallic frame with the cut side exposed.the joints must be staggered as in any normal dry covering application. 5. Between one board and the next leave about 3-4 mm. 6. We recommend not keeping the edge of the board in direct contact with the supporting surface in order to prevent the capillary rise of any humidity, salts or impurities from the supporting surface. 7. Fixing Aquafire boards with Screws Aquafire Star screwing from cut side with step 20cm (15cm for horizontal applications); a distance of about 15 mm is indicated from the edge in order to best take advantage of the boards contact with the large surface of the screw head. 8. Spread a layer of Rasante Aquafire coat on the longitudinal and transversal joints 150 mm wide. 9. Embed the 75 mm Nastro Aquafire mesh for joints in the plaster as soon as it is spread; 10. Once 12 hours have passed after filling the joints, spread a layer of Rasante Aquafire on the entire surface of the boards with a notched trowel steel. 11. Embed the Rete Aquafire mesh in the cement coat which has just been spread, taking care to hide it completely, working with the smooth side of the trowel steel. 12. At this point the final thickness of coating must be 3mm. 13. Complete the surface with a finish plaster walls like acrylic plaster, acrylic-siloxane or siloxane. Indoor 1. The boards will be installed on suitable metallic frames depending on whether the installation is on walls, linings walls or ceiling. 2. we recommend using metallic profiles in compliance with the UNI EN standard with 6/10mm thickness. 3. Arrange the frames one step no greater than 40cm. 4. Aquafire boards must be installed to the metallic frame with the cut side exposed.the joints must be staggered as in any normal dry covering application. 5. Between one board and the next leave about 3-4 mm. 6. We recommend not keeping the edge of the board in direct contact with the supporting surface in order to prevent the capillary rise of any humidity, salts or impurities from the supporting surface. 7. Fixing Aquafire boards with Screws Aquafire Star screwing from cut side with step 25cm (15cm for horizontal applications); a distance of about 15 mm is indicated from the edge in order to best take advantage of the boards contact with the large surface of the screw head. 8. Spread a layer of Finish coat on the longitudinal and transversal joints 150 mm wide. 9. Embed the 75 mm Nastro Aquafire mesh for joints in the plaster as soon as it is spread; 10. Once 24 hours have passed, smoothing the entire surface of the boards with Finish. 11. Now the wall is ready for painting. Curved surface To create curved surfaces you can use the whole Aquafire boards up to a minimum radius of 2 meters. For rays less and up to 90cm use boards of a width of 30cm, screwing them to the support with Screws Aquafire Star to step 10cm. 17
SISTEMA AQUAFIRE vs. SISTEMA TRADIZIONALE AQUAFIRE SYSTEM vs. TRADITIONAL SYSTEM PARETE DI TAMPONAMENTO ESTERNA Rasante Aquafire Lastra Aquafire Tyvek Montante in acciaio 188 3 12,5 75 12,5 10 50 12,5 12,5 70 Intonaco Laterizio 300 15 120 70 80 15 Lana di roccia sp.70mm d.70kg/mc Lastra cartongesso Aria Lana di roccia Laterizio Intonaco Montante in acciaio Lana di roccia sp.50mm d.70kg/mc Lastra cartongesso Lastra cartongesso con barriera al vapore 188mm SPESSORE 300mm 0,249 W/m K U 0,380 W/m K Costruzione struttura 75mm - posa Tyvek - posa lastre Aquafire - stuccatura giunti Rasatura esterna - ldr 70/70 - posa ctg 1 strato struttura 50mm - lana di roccia 50/70 ctg 2 strato ctg con barriera al vapore - stuccatura viti e giunti 1 Posa laterizio 12cm - posa lana di roccia posa laterizio 8cm 2 Creazione fasce porta intonaco Seconda e terza mano della stuccatura interna 3 Intonacatura Tinteggiatura interna - Finitura acrilsilossanica esterna 4 Asciugatura intonaco 5 Asciugatura intonaco 6 Posa intonachino esterno posa veletto di finitura interno PIU VELOCE DA INSTALLARE PIU ISOLANTE 7 Asciugatura delle finiture 8 Tinteggiatura interna - tinteggiatura esterna 4 GIORNI 8 GIORNI 18
SISTEMA AQUAFIRE vs. SISTEMA TRADIZIONALE AQUAFIRE SYSTEM vs. TRADITIONAL SYSTEM OUTDOOR COURTAIN WALL Rasante Aquafire Aquafire board 188 3 12,5 75 13 10 50 12,512,5 70 Plaster 300 15 120 70 80 15 Tyvek Metallic frame Rock wool th.70mm d.70kg/mc Plasterboard Air Brick Rock wool Brick Plaster Metallic frame Rock wool th.50mm d.70kg/mc Plasterboard Plasterboard with vapour barrier 188mm THICKNESS 300mm 0,249 W/m K U 0,380 W/m K Frame construction 75mm - Inst. Tyvek inst. Aquafire boards - fill the joints external plastering - rock w.70/70 - inst. p.board 1 layer - frame 50mm - rock w. 50/70 - p.board 2 layer - p.board vapour barrier - fill the joints 1 laying birck 12cm - inst. rock wool laying brick 8cm 2 Creating slings plaster Second and third layer of internal plastering 3 Plastering External painting - external acrylic-siloxane finishing 4 Drying plaster FASTER TO INSTALL MORE INSULATION 5 Drying plaster 6 Laying external plaster - Laying fixative of interior finish 7 Drying 8 Internal and external painting 4 DAYS 8 DAYS 19
SISTEMA AQUAFIRE vs. SISTEMA TRADIZIONALE AQUAFIRE SYSTEM vs. TRADITIONAL SYSTEM SOSTITUZIONE INTONACO 145 12,5 120 12,5 150 15 120 15 Lisciatura con Finish Intonaco Lastra Aquafire Laterizio Laterizio Intonaco Lastra Aquafire Lisciatura con Finish 145mm SPESSORE 150mm 1,293 W/m K U 1,794 W/m K Posa Aquafire - Stuccatura giunti con Finish 1 Creazione fasce porta intonaco Lisciatura parete con Finish 2 Intonacatura Tinteggiatura 3 Asciugatura intonaco PIU VELOCE DA INSTALLARE 4 Asciugatura intonaco 5 Posa intonachino esterno - posa veletto di finitura interno 6 Posa intonachino esterno posa veletto di finitura interno 7 Tinteggiatura interna - tinteggiatura esterna 3 GIORNI 7 GIORNI 20
SISTEMA AQUAFIRE vs. SISTEMA TRADIZIONALE AQUAFIRE SYSTEM vs. TRADITIONAL SYSTEM PLASTER REPLACEMENT 145 12,5 120 12,5 150 15 120 15 Smoothing with Finish Plaster Aquafire board Brick Brick Plaster Aquafire board Smoothing with Finish 145mm THICKNESS 150mm 1,293 W/m K U 1,794 W/m K Inst. Aquafire boards - fill the joints with Finish 1 Creating slings plaster Smoothing the boards with Finish 2 Plastering Painting 3 Drying plaster 4 Drying plaster FASTER TO INSTALL 5 Laying external plaster - installation fixative of interior finish 6 Laying external plaster - installation fixative of interior finish 7 Internal and external painting 3 DAYS 7 DAYS 21
SISTEMA AQUAFIRE vs. SISTEMA TRADIZIONALE AQUAFIRE SYSTEM vs. TRADITIONAL SYSTEM PARETE INTERNA 100 12,5 75 12,5 110 15 80 15 Lisciatura con Finish Intonaco Lastra Aquafire Montante in acciaio Laterizio Lana di roccia sp.70mm d.70kg/mc Intonaco Lastra Aquafire Lisciatura con Finish 100mm SPESSORE 110mm - U - Costr. struttura 75mm - corrugati per imp. elettrico - lana di roccia - posa Aquafire - scatole elettriche - stuccatura giunti e teste delle viti con Rasante Finish Lisciatura lastre con Rasante Finish 2 PIU VELOCE DA INSTALLARE 1 Costruzione muro in mattoni - Creazione fasce porta intonaco traccie impianto elettrico - passaggio corrugati posa scatole elettriche - chiusura traccie Tinteggiatura 3 Intonacatura 4 Asciugatura intonaco 5 Asciugatura intonaco 6 Veletto di finitura su entrambe le faccie 7 Asciugatura veletto 8 Tinteggiatura 3 GIORNI 8 GIORNI 22
SISTEMA AQUAFIRE vs. SISTEMA TRADIZIONALE AQUAFIRE SYSTEM vs. TRADITIONAL SYSTEM INDOOR WALL 100 12,5 75 12,5 110 15 80 15 Smoothing with Finish Plaster Aquafire board Metallic frame Brick Rock wool th.70mm d.70kg/mc Plaster Aquafire board Smoothing with Finish 100mm THICKNESS 110mm - U - Inst. frame 75mm - corrug. electr. - inst. rock wool - inst. Aquafire - electr. box- fill the joints with Finish 1 Laying birck wall - Creating slings plaster Smoothing the boards with Finish 2 Tracks electrical system - corrugated passage - installing electrical boxes - closing tracks Painting 3 Plastering 4 Drying plaster 5 Drying plaster FASTER TO INSTALL 6 Laying fixative of both faces 7 Drying fixative 8 Painting 3 DAYS 8 DAYS 23
SCHEDE TECNICHE TECHNICAL DATA SHEET AQUAFIRE Generalità General info Lastra in cemento alleggerito fibrorinforzato. Fibre-reinforced lightweight cement boards. Utilizzo Use Caratteristiche Characteristics Descrizione Description Civile ed industriale. CIvil and industrial. Leggerissima, altamente isolante, è la lastra che si taglia più facilmente sul mercato, resistente all acqua per l impiego in ambienti ad elevata umidità, può essere utilizzata per applicazioni interne od esterne, non marcisce, non si deforma, non si sfalda ne si disgrega. Fornita con lato liscio per applicazioni interne con stuccatura tradizionale e lato ruvido per applicazioni di intonaci e rasanti. Extremely lightweight, highly insulating, this is the easiest board to cut on the market, water resistant for use in high humidity ambient, it can be used for indoor or outdoor applications. It does not decay, deform, flake or crumble. Provided with a smooth side for indoor applications with traditional plastering and a rough side for cement coat applications. Le lastre AQUAFIRE offrono un supporto eccezionale e resistente per l applicazione di piastrelle in ceramica, mosaici in vetro, rivestimenti in laterizi o di altra natura. Possono essere rasate per ottenere una superficie liscia pronta per la pittura. Le lastre AQUAFIRE sono idonee all applicazione su orditure in legno o acciaio, con elementi posti ad interasse di 400 mm. in nuove costruzioni e ristrutturazioni. La lastra AQUAFIRE è ideale per pareti divisorie, contropareti, massetti a secco, intradossi e controsoffitti in ambienti umidi o asciutti, e per la riqualificazione energetica. Non subisce deterioramenti in presenza d acqua, di qui la sua elevata durabilità in ambienti saturi di umidità, quali bagni, docce, cucine, lavanderie e ambienti esterni. I principali impieghi sono rivolti alla costruzione di facciate ventilate, pareti esterne, coperture, rivestimenti di canne fumarie, recinzioni esterne, zoccolature, fabbricati per uso agricolo, garage, supporto per rivestimenti. AQUAFIRE boards provide exceptional and resistant support for the application of ceramic tiles, glass mosaics brick coverings or any other type of covering. They can be skim plastered to obtain a smooth surface ready for painting. AQUAFIRE boards are ideal for application on wood or steel frames with elements at a centre distance of 400 mm in new constructions or renovations. The AQUAFIRE board is ideal for dividing walls, linings walls, dry blocks, soffits and false ceilings in humid or dry ambient and for retrofit upgrades. It does not deteriorate in the presence of water and this makes it long lasting in high humidity ambient such as bathrooms, showers, kitchens, laundry rooms as well as in outdoor ambient. Primary use is intended for the construction of ventilated façades, external walls, roofs, chimney flues, outdoor fencing, skirting, buildings for agricultural use, garages and supports for coverings. 24
SCHEDE TECNICHE TECHNICAL DATA SHEET CARATTERISTICHE TECNICHE TECHNICAL CHARACTERISTICS Descrizione Description Densità a secco Dry density Peso Weight Larghezza Width Lunghezza Length Spessore Thickness Reazione al fuoco Reaction to fire U.M. Valore Value Tolleranze Tolerances [kg/m 3 ] 960 ± 15 % [kg/m 2 ] 12 ± 15 % [mm] 1200 ± 3.6 mm [mm] 2000 ± 5 mm [mm] 12.5 ± 1.2 mm - A1 - Resistenza al fuoco Fire resistance [min] 240 - Conducibilità termica a 10 C Thermal conductivity at 10 C [W/m K] 0.096 - Conducibilità termica a 20 C Thermal conductivity at 20 C [W/m K] 0.097 - Resistenza alla flessione Bending resistance [MPa] 5 - Raggio di curvatura lastra intera Radius of curvature whole board [m] 2,0 - Raggio di curvatura lastra 30cm Radius of curvature whole 30cm [m] 0,9-25
SCHEDE TECNICHE TECHNICAL DATA SHEET VITE AQUAFIRE STAR Generalità General info Tipo di materiale Type of material Utilizzo Use Descrizione Description Vite a punta trapano. Teks screw. Acciaio trattato resistente a 1000 ore di nebbia salina. Treated steel resistant to 1000 hours of salt spray. Fissaggio di lastre AQUAFIRE su struttura di spessore superiore a 0.6mm. Affixing AQUAFIRE boards on a structure with thickness greater than 0.6 mm. Le VITI AQUAFIRE STAR sono idonee al fissaggi di lastre AQUAFIRE su strutture in acciaio con spessore da 0.6mm fino a 1mm. Sono resistenti alla nebbia salina per 1000 ore così da garantire la loro durabilità anche in ambienti aggressivi o esposti direttamente agli agenti atmosferici. Sono auto perforanti e auto svasanti così da facilitare sia la perforazione del profilo metallico che la presa sullo spessore della lastra AQUAFIRE. VITI AQUAFIRE STAR are ideal for securing AQUAFIRE boards onto 0.6 mm up to 1 mm thick steel structures. They are resistant to salt spray for 100 hours in order to guarantee long life even in aggressive ambient or when exposed directly to atmospheric agents. They are self-drilling and self-countersinking in order to facilitate both perforation of the metallic profile and the adherence to the surface of the AQUAFIRE board. CARATTERISTICHE TECNICHE TECHNICAL CHARACTERISTICS Descrizione Description Diametro Diameter Lunghezza Length Resistenza nebbia salina Salt spray resistance Incidenza Incidence U.M. Valore Value [mm] 4.2 [mm] 40 ore >1000 n /m 2 20 PIU VELOCE DA AVVITARE FASTER TO SCREW PIU FACILE DA AVVITARE EASIER TO SCREW 26
SCHEDE TECNICHE TECHNICAL DATA SHEET NASTRO AQUAFIRE Generalità General info Tipo di materiale Type of material Utilizzo Use Descrizione Description Nastro coprigiunto. Joint cover mesh tape. Fibra di vetro alcali resistant. Alkali resistant fibreglass. Nastratura dei giunti fra lastre AQUAFIRE. Taping over joints between AQUAFIRE boards. Nastro coprigiunto in rete di fibra di vetro ideale per la stuccatura dei giunti longitudinali e trasversali fra le lastre AQUAFIRE. Il NASTRO AQUAFIRE è resistente agli alcali e non teme l effetto degli agenti atmosferici. Joint covering mesh tape in fibreglass, ideal for filling longitudinal and transversal joints between AQUAFIRE boards. NASTRO AQUAFIRE is resistant to alkali and to the effect of atmospheric agents. CARATTERISTICHE TECNICHE TECHNICAL CHARACTERISTICS Descrizione Description Larghezza rotolo Roll width Lunghezza rotolo Roll length Incidenza Incidence U.M. Valore Value [mm] 75 [m] 50 m/m 2 1.4 27
SCHEDE TECNICHE TECHNICAL DATA SHEET RASANTE AQUAFIRE Generalità General info Utilizzo Use Rasante premiscelato cementizio monocomponente in polvere alleggerito. Premixed single component cement coating in lightweight powder. Rasatura in ambienti esterni di lastre AQUAFIRE. Coating of AQUAFIRE boards outdoor ambient. Descrizione Description Il RASANTE AQUAFIRE attraverso il suo alleggerimento conferisce una maggiore scorrevolezza e facilità di posa. E caratterizzato da un alto potere adesivo connesso ad una elevata elasticità Il RASANTE AQUAFIRE ha ridotti tempi di essiccamento ed elevata resa. Il RASANTE AQUAFIRE è dunque più facile da posare, più economico, più isolante e ne occorre solo 3,6kg/mq per sistemi in esterno. RASANTE AQUAFIRE thanks to Its lightweight quality has a greater smoothness and ease of application. It is characterised by high adhesive strength connected to high elasticity. RASANTE AQUAFIRE has a reduced drying time and high yield. RASANTE AQUAFIRE is therefore easier to install, cheaper, more insulation and it should only 3.6 kg / sqm for outdoor systems. PIU ECONOMICO CHEAPER PIU FACILE DA POSARE EASIER TO INSTALL SOLO 3,6 Kg/mq ONLY 3,6Kg/sm PIU ISOLANTE MORE INSULATION PER SISTEMI IN ESTERNO FOR OUTDOOR SYSTEM 28
SCHEDE TECNICHE TECHNICAL DATA SHEET CARATTERISTICHE TECNICHE TECHNICAL CHARACTERISTICS Descrizione Description Quantità a sacco Bag quanity Granulometria Grain size Acqua di impasto Mixing water Massa volumica malta fresca Fresh mortar volume mass Massa volumica apparente prodotto indurito Apparent volume mass of hardened product Tempo di vita impasto Mix life Tempo di riposo impasto Mix standby time Ritenzione d acqua Water retention Resistenza a compressione media Average compressive strength Resistenza a flessione media Average bending strength Assorbimento d acqua per capillarità Capillary water absorption Permeabilità al vapor d acqua Vapour permeability Resistenza alla perforazione Resistance to perforation Resistenza all impatto Impact resistance Resa indicativa Approximate yield Conducibilità termica a 10 C Thermal conductivity at 10 C U.M. Valore Value [kg] 18 [mm] <1.0 [%] 27-28 [gr/m 3 ] 1.2 [kg/m 3 ] 1050 [h] 8 [min] 10 [%] 99 [MPa] 10.5 [MPa] 4.5 [kg/m 2 ] <1 [mm] <2 [N] 476.7 [10J] Non deteriorato Not deteriorated [kg/m 2 x mm] 1.2 [W/m K] 0.15323 29
SCHEDE TECNICHE TECHNICAL DATA SHEET FINISH Generalità General info Utilizzo Use Descrizione Description Rasante premiscelato cementizio monocomponente in polvere. Premixed single component cement coating in powder. Rasatura in ambienti interni di lastre AQUAFIRE. Coating of AQUAFIRE boards in indoor ambient. Il FINISH è studiato per applicazioni in ambienti interni, con rilevanti valori di umidità relativa dell aria. FINISH possiede elevate caratteristiche di adesione e lavorabilità. Il FINISH ha ridotti tempi di essiccamento ed elevata resa. FINISH is designed for indoor applications, with significant values of relative humidity. FINISH has high adhesion and workability. FINISH has reduced drying times and high yield. PIU ECONOMICO CHEAPER PIU ELASTICO MORE ELASTIC PER SISTEMI IN INTERNO FOR INDOOR SYSTEM PIU TRASPIRANTE MORE BREATHABLE PIU RESISTENTE ALL UMIDITA MORE HUMIDITY RESISTANT 30
SCHEDE TECNICHE TECHNICAL DATA SHEET CARATTERISTICHE TECNICHE TECHNICAL CHARACTERISTICS Descrizione Description Quantità a sacco Bag quanity Granulometria Grain size Acqua di impasto Mixing water Massa volumica malta fresca Fresh mortar volume mass Tempo di vita impasto Mix life Tempo di presa Setting time Resistenza a compressione media Average compressive strength Resistenza a flessione media Average bending strength Resa indicativa Approximate yield U.M. Valore Value [kg] 25 [mm] <0,315 [%] 24 [gr/m 3 ] 1,56 [min] 15 [min] 20-30 [MPa] 15,0 [MPa] 5,0 [kg/m 2 x mm] 1.5 31
SCHEDE TECNICHE TECHNICAL DATA SHEET RETE AQUAFIRE Generalità General info Tipo di materiale Type of material Utilizzo Use Rete di armatura superficiale. Surface reinforcing mesh. Fibra di vetro alcali resistant. Alkali resistant fibreglass. Armatura del primo strato di rasatura delle lastre AQUAFIRE. Reinforcing for the first layer of skim plastering on AQUAFIRE boards. Descrizione Description Rete in fibra di vetro ideale per armare il primo strato di rasatura delle lastre AQUAFIRE. La RETE AQUAFIRE è resistente agli alcali e non teme l effetto degli agenti atmosferici. Fibreglass mesh ideal for reinforcing the first layer of cement coating on AQUAFIRE boards. RETE AQUAFIRE is resistant to alkali and has no fear of atmospheric agents. CARATTERISTICHE TECNICHE TECHNICAL CHARACTERISTICS Descrizione Description Altezza rotolo Roll height Lunghezza rotolo Roll length Incidenza Incidence U.M. Valore Value [mm] 1000 [m] 50 m/m 2 1.2 32
ESPANSIONE AQUAFIRE Generalità General info Tipo di materiale Type of material Utilizzo Use Coprigiunto di dilatazione. Expansion joint cover. Materiale plastico. Plastic material. Mascheramento del giunto di dilatazione per lastre AQUAFIRE. Masking of the expansion joint for AQUAFIRE boards. SCHEDE TECNICHE TECHNICAL DATA SHEET Descrizione Description Coprigiunto per il mascheramento dei giunti di dilatazione od espansione. ESPANSIONE AQUAFIRE è dotato di pellicola removibile che garantisce la pulizia e la precisione della giunzione: una volta finita la rasatura della parete AQUAFIRE è sufficiente sollevare la linguetta e tirare leggermente lasciando il giunto preciso e pulito. Joint cover for masking expansion joints. ESPANSIONE AQUAFIRE has a removable film which ensures cleaning and precision of the joint: once skim plastering of the AQUAFIRE is completed, simply lift the tab and pull lightly. The protective film will come off easily, leaving the joint precise and clean. CARATTERISTICHE TECNICHE TECHNICAL CHARACTERISTICS Descrizione Description Larghezza Width Larghezza giunto Joint width Profondità giunto Joint depth Lunghezza Length U.M. Valore Value [mm] 57 [mm] 13 [mm] 13 [mm] 3000 33
APPLICAZIONI VERTICALI vertical APPLICATIONS 35
PARETE AQUAFIRE PER AMBIENTI INTERNI INDOOR AQUAFIRE WALL Fornitura e posa in opera di parete divisoria per interni dello spessore totale di 100mm composta da orditura metallica e rivestimento in lastre di cemento alleggerito Aquafire. Supply and installation of indoor dividing walls with a total thickness of 100 mm comprised of metallic frames and covering in lightweight cement Aquafire boards. Realizzare la struttura metallica con profili in acciaio zincato con dimensioni pari a 75x40x0.6mm per le guide a "U", e 75x50x0.6mm per i montanti a C, posti ad interasse di 400mm, il tutto desolidarizzato dalle strutture perimetrali con apposito monoadesivo con funzione di isolante termoacustico. Build a metallic structure with 75x40x0.6 mm galvanized steel profiles for the "U" guides and 75x50x0.6 mm for C stanchions, placed at a centre distance of 400 mm, all separated from the perimeter structure with specific thermal insulating single-sided tape. Install a layer of 12.5 mm thick lightweight cement Aquafire boards on both sides of the frame, leaving 3-4 mm between the joints of one slab and the next, cut side exposed. Posare su entrambi i lati dell'orditura uno strato di lastre Aquafire in cemento alleggerito sp. 12,5mm, lasciando fra una lastra e l altra 3-4mm fra i giunti, lato taglio a vista. The boards will be affixed to the structure with Viti Aquafire Star screws at a maximum pitch of 250mm. A distance of about 15 mm is indicated from the edge. Le lastre verranno fissate alla struttura con Viti Aquafire Star ad un passo massimo di 250mm. Si indica una distanza dal bordo di c.a. mm 15. Spalmare uno strato di Finish sui giunti longitudinali e trasversali, largo 150mm. Spread a layer of Finish on the longitudinal and transversal joints 150 mm wide. Embed the 75 mm Nastro Aquafire mesh tape in the coat as soon as it is spread. Once 24 hours have passed, smoothing the entire surface of the boards with Finish. Annegare la rete per giunti Nastro Aquafire da 75mm nel rasante appena posato. Dopo 24 ore, lisciare la parete con Finish in un unica mano Le caratteristiche dei materiali saranno quelle prescritte da Bifire s.r.l.. The characteristics of the materials will be those prescribed by Bifire s.r.l. 36
RIQUALIFICAZIONE INTERNA CON AQUAFIRE INDOOR UPGRADING WITH AQUAFIRE Fornitura e posa in opera di controparete per interni composta da orditura metallica e rivestimento in lastre di cemento alleggerito Aquafire e isolante termico Vacunanex. Realizzare la struttura metallica con profili in acciaio zincato con dimensioni pari a 28x30x0.6mm per le guide a "U", e 49x27x0.6mm per i montanti a C, posti ad interasse di 400mm e vincolati alla parete con distanziatori tali da garantire un intercapedine d aria di almeno 20mm. Inserire nell intercapedine i pannelli isolanti sottovuoto Vacunanex sp.20mm così da garantire con il solo isolante 2 una U=0.22 W/m K V V Posare uno strato di lastre in cemento Aquafire alleggerito sp. 12,5mm lasciando fra una lastra e l altra 3-4mm fra i giunti, lato taglio a vista. U= 0,22 W /m 2 K Build a metallic structure with 28x30x0.6 mm galvanized steel profiles for the "U" guides and 49x27x0.6 mm for C stanchions, placed at a centre distance of 400 mm and constrained to the walls with spacers in order to guarantee an air cavity of at least 20 mm. Insert the 20 mm thick Vacunanex insulating vacuum panels into the cavity in order to guarantee U=0.22 W/m2K with just the insulation Install a layer of 12.5 mm thick lightweight cement Aquafire boards, leaving 3-4 mm between the joints of one slab and the next, cut side exposed. Le lastre verranno fissate alla struttura con Viti Aquafire Star ad un passo massimo di 250mm. Si indica una distanza dal bordo di c.a. mm 15. Spalmare uno strato di Finish sui giunti longitudinali e trasversali, largo 150mm. Annegare la rete per giunti Nastro Aquafire da 75mm nel rasante appena posato. Dopo 24 ore, lisciare la parete con Finish in un unica mano. Supply and installation of double walls for indoor environments comprised of metallic frame and covering in Aquafire lightweight cement boards and Vacunanex thermal insulation. The boards will be affixed to the structure with Viti Aquafire Star screws at a maximum pitch of 250mm. A distance of about 15 mm is indicated from the edge. Spread a layer of Finish on the longitudinal and transversal joints 150 mm wide. Embed the 75 mm Nastro Aquafire mesh tape in the plaster as soon as it is spread. Once 24 hours have passed, smoothing the entire surface of the boards with Finish. Le caratteristiche dei materiali saranno quelle prescritte da Bifire s.r.l.. The characteristics of the materials will be those prescribed by Bifire s.r.l. 37
PARETI DI TAMPONAMENTO AQUAFIRE PER ESTERNI AQUAFIRE CURTAIN WALLS FOR OUTDOORS Fornitura e posa in opera di parete perimetrale per esterni composta da orditura metallica e rivestimento in lastre di cemento alleggerito Aquafire. Supply and installation of outdoor curtain walls comprised of metallic frames and covering in lightweight cement Aquafire boards. Realizzare la struttura metallica con profili in acciaio zincato con dimensioni pari a 75x50x1.0mm per le guide a "U", e 75x50x1.0mm per i montanti a C, posti ad interasse di 400mm. Build a metallic structure with 100x40x1.0 mm galvanized steel profiles for the "U" guides and 100x50x1.0 mm for C stanchions, placed at a centre distance of 400 mm. Insert the insulating material, appropriately sized based on the building's energy performance, in the metallic frame. Inserire nell orditura metallica il materiale isolante opportunamente dimensionato in funzione della prestazione energetica dell edificio. Install a layer of 12.5 mm thick lightweight cement Aquafire boards on the outside of the frame, leaving 3-4 mm between the joints of one slab and the next, taking care to keep the slab raised off the ground at least 5 mm, cut side exposed. Posare sul lato esterno dell'orditura uno strato di lastre Aquafire in cemento alleggerito sp. 12,5mm lasciando fra una lastra e l altra 3-4mm fra i giunti, avendo cura di tenere le lastre sollevate da terra per almeno 5mm, lato taglio a vista. The boards will be affixed to the structure with Viti Aquafire Star screws at a maximum pitch of 200mm. A distance of about 15 mm is indicated from the edge. Le lastre verranno fissate alla struttura con Viti Aquafire Star ad un passo massimo di 200mm. Si indica una distanza dal bordo di c.a. mm 15. Spread a layer of Rasante Aquafire on the longitudinal and transversal joints 150 mm wide and at a minimum thickness of 2-3mm. Spalmare uno strato di Rasante Aquafire sui giunti longitudinali e trasversali, largo 150mm. Annegare la rete per giunti Nastro Aquafire da 75mm nel rasante appena posato; Passato il tempo di asciugatura di 12 ore, spalmare uno strato di Rasante Aquafire sull intera superficie della lastra con frattazzo dentato in acciaio. Annegare la Rete Aquafire nel rasante appena posato, avendo cura di nasconderla completamente, lavorando con il lato liscio del frattazzo dentato. A questo punto lo spessore finale della rasatura deve essere di 3mm. Embed the 75 mm Nastro Aquafire mesh tape in the plaster as soon as it is spread. Finire la superficie con rivestimento murale. After 12 hours have passed from filling the joints. Spread a layer of Rasante Aquafire over the entire surface at a min. thickness of 5-7 mm. Embed the Rete Aquafire mesh in the plaster which has just been spread, taking care to hide it completely; the Rete Aquafire mesh must have an overlap of 100 mm. The final thickness must be at least 5 mm. For final skim plastering you can use Rasante Aquafire again for another 2 mm layer in order to perfect the surface and eliminate any irregularities; At this point the total thickness of the finished cement coating should be about 7 mm. Le caratteristiche dei materiali saranno quelle prescritte da Bifire s.r.l.. The characteristics of the materials will be those prescribed by Bifire s.r.l. 38
RIVESTIMENTO ESTERNO DI FACCIATA CON AQUAFIRE EXTERNAL FAÇADE COVERING WITH AQUAFIRE Fornitura e posa in opera di controparete per esterni composta da orditura metallica e rivestimento in lastre di cemento alleggerito Aquafire. Realizzare la struttura metallica con profili in acciaio zincato con dimensioni pari a 28x30x1.0mm per le guide a "U", e 49x27x1.0mm per i montanti a C, posti ad interasse di 400mm e vincolati alla parete con distanziatori tali da garantire la verticalità del manufatto. Posare uno strato di lastre Aquafire in cemento alleggerito sp. 12,5mm lasciando fra una lastra e l altra 3-4mm fra i giunti, avendo cura di tenere le lastre sollevate da terra per almeno 5mm, lato taglio a vista. Le lastre verranno fissate alla struttura con Viti Aquafire Star ad un un passo massimo di 200mm. Si indica una distanza dal bordo di c.a. mm 15. Spalmare uno strato di Rasante Aquafire sui giunti longitudinali e trasversali, largo 150mm. Annegare la rete per giunti Nastro Aquafire da 75mm nel rasante appena posato; Passato il tempo di asciugatura di 12 ore, spalmare uno strato di Rasante Aquafire sull intera superficie della lastra con frattazzo dentato in acciaio. Annegare la Rete Aquafire nel rasante appena posato, avendo cura di nasconderla completamente, lavorando con il lato liscio del frattazzo dentato. A questo punto lo spessore finale della rasatura deve essere di 3mm. Finire la superficie con intonachino acrilico, acrilsilossanico o silossanico. Supply and installation of outdoor double walls comprised of metallic frames and covering in lightweight cement Aquafire boards. Build a metallic structure with 28x30x1.0 mm galvanized steel profiles for the "U" guides and 49x27x1.0 mm for C stanchions, placed at a centre distance of 400 mm and constrained to the walls with spacers in order to guarantee that the product is vertical. Install a layer of 12.5 mm thick lightweight cement Aquafire slabs, leaving 3-4 mm between the joints of one slab and the next, taking care to keep the slab raised off the ground at least 5 mm, cut side exposed. The boards will be affixed to the structure with Viti Aquafire Star screws at a maximum pitch of 200mm. A distance of about 15 mm is indicated from the edge. Spread a layer of Rasante Aquafire coat on the longitudinal and transversal joints 150 mm wide. Embed the 75 mm Nastro Aquafire mesh for joints in the plaster as soon as it is spread; Once 12 hours have passed after filling the joints, spread a layer of Rasante Aquafire on the entire surface of the boards with a notched trowel steel. Embed the Rete Aquafire mesh in the cement coat which has just been spread, taking care to hide it completely, working with the smooth side of the trowel steel. At this point the final thickness of coating must be 3mm. Finish the surface with acrylic plaster, acrylic-siloxane or siloxane. Le caratteristiche dei materiali saranno quelle prescritte da Bifire s.r.l.. The characteristics of the materials will be those prescribed by Bifire s.r.l. 39
CAPPOTTO AQUAFIRE PER ESTERNI AQUAFIRE EXTERNAL CLADDING Fornitura e posa in opera di cappotto per esterni composto da orditura metallica e rivestimento in lastre di cemento alleggerito Aquafire Supply and installation of external cladding comprised of metallic frame and covering in Aquafire lightweight cement boards. Realizzare la struttura metallica con profili in acciaio zincato con dimensioni pari a 28x30x1.0mm per le guide a "U", e 49x27x1.0mm per i montanti a C, posti ad interasse di 400mm e vincolati alla parete con distanziatori tali da garantire la verticalità del manufatto. Build a metallic structure with 28x30x1.0 mm galvanized steel profiles for the "U" guides and 49x27x1.0 mm for C stanchions, placed at a centre distance of 400 mm and constrained to the walls with spacers in order to guarantee that the product is vertical. Enter in to the cavity insulation panels as required by thermal calculation Inserire nell intercapedine i pannelli isolanti necessari come da calcolo termico Posare uno strato di lastre Aquafire in cemento alleggerito sp. 12,5mm lasciando fra una lastra e l altra 3-4mm fra i giunti, avendo cura di tenere le lastre sollevate da terra per almeno 5mm, lato taglio a vista. Le lastre verranno fissate alla struttura con Viti Aquafire Star ad un passo massimo di 200mm. Si indica una distanza dal bordo di c.a. mm 15. Spalmare uno strato di Rasante Aquafire sui giunti longitudinali e trasversali, largo 150mm. Annegare la rete per giunti Nastro Aquafire da 75mm nel rasante appena posato; Passato il tempo di asciugatura di 12 ore, spalmare uno strato di Rasante Aquafire sull intera superficie della lastra con frattazzo dentato in acciaio. Annegare la Rete Aquafire nel rasante appena posato, avendo cura di nasconderla completamente, lavorando con il lato liscio del frattazzo dentato. A questo punto lo spessore finale della rasatura deve essere di 3mm. Finire la superficie con intonachino acrilico, acrilsilossanico o silossanico. Install a layer of 12.5 mm thick lightweight cement Aquafire boards, leaving 3-4 mm between the joints of one slab and the next, taking care to keep the slab raised off the ground at least 5 mm, cut side exposed. The boards will be affixed to the structure with Viti Aquafire Star screws at a maximum pitch of 200mm. A distance of about 15 mm is indicated from the edge. Spread a layer of Rasante Aquafire coat on the longitudinal and transversal joints 150 mm wide. Embed the 75 mm Nastro Aquafire mesh for joints in the plaster as soon as it is spread; Once 12 hours have passed after filling the joints, spread a layer of Rasante Aquafire on the entire surface of the boards with a notched trowel steel. Embed the Rete Aquafire mesh in the cement coat which has just been spread, taking care to hide it completely, working with the smooth side of the trowel steel. At this point the final thickness of coating must be 3mm. Finish the surface with acrylic plaster, acrylic-siloxane or siloxane. Le caratteristiche dei materiali saranno quelle prescritte da Bifire s.r.l.. The characteristics of the materials will be those prescribed by Bifire s.r.l. 40
FACCIATA VENTILATA AQUAFIRE AQUAFIRE VENTILATED FAÇADE Fornitura e posa in opera di facciata ventilata esterna composta da orditura metallica e rivestimento in lastre di cemento alleggerito Aquafire. Supply and installation of external ventilated façade comprised of metallic frames and covering in lightweight cement Aquafire boards. Realizzare la struttura metallica con profili in acciaio zincato con dimensioni pari a 28x30x1.0mm per le guide a "U", e 49x27x1.0mm per i montanti a C, posti ad interasse di 400mm e vincolati alla parete con distanziatori tali da garantire un intercapedine d aria sufficiente all alloggiamento del materiale coibente. Inserire nell orditura metallica il materiale isolante opportunamente dimensionato. Posare i distanziatori metallici in maniera tale da avere una distanza di minimo 25mm fra isolante e lastra per garantire la ventilazione naturale della facciata. Posare uno strato di lastre Aquafire in cemento alleggerito sp. 12,5mm lasciando fra una lastra e l altra 3-4mm fra i giunti, avendo cura di tenere le lastre sollevate da terra per almeno 5mm, lato taglio a vista. Le lastre verranno fissate alla struttura con Viti Aquafire Star ad un un passo massimo di 200mm. Si indica una distanza dal bordo di c.a. mm 15. Spalmare uno strato di Rasante Aquafire sui giunti Build a metallic structure with 28x30x1.0 mm galvanized steel profiles for the "U" guides and 49x27x1.0 mm for C stanchions, placed at 400 mm intervals and constrained to the walls with spacers in order to guarantee an air cavity sufficient to house the insulating material. Insert the insulating material, appropriately sized in the metallic frame. longitudinali e trasversali, largo 150mm. Annegare la rete per giunti Nastro Aquafire da 75mm nel rasante appena posato; Passato il tempo di asciugatura di 12 ore, spalmare uno strato di Rasante Aquafire sull intera superficie della lastra con frattazzo dentato in acciaio. Annegare la Rete Aquafire nel rasante appena posato, avendo cura di nasconderla completamente, lavorando con il lato liscio del frattazzo dentato. A questo punto lo spessore finale della rasatura deve essere di 3mm. Finire la superficie con intonachino acrilico, acrilsilossanico o silossanico. Install the metallic spacers in such a way so as to have a minimum distance of 25 mm between insulation and the boards in order to guarantee the natural ventilation of the façade. Install a layer of 12.5 mm thick lightweight cement Aquafire boards, leaving 3-4 mm between the joints of one slab and the next, taking care to keep the slab raised off the ground at least 5 mm, cut side exposed. The boards will be affixed to the structure with Viti Aquafire Star screws at a maximum pitch of 200mm. A distance of about 15 mm is indicated from the edge. Spread a layer of Rasante Aquafire coat on the longitudinal and transversal joints 150 mm wide. Embed the 75 mm Nastro Aquafire mesh for joints in the plaster as soon as it is spread; Once 12 hours have passed after filling the joints, spread a layer of Rasante Aquafire on the entire surface of the boards with a notched trowel steel. Embed the Rete Aquafire mesh in the cement coat which has just been spread, taking care to hide it completely, working with the smooth side of the trowel steel. At this point the final thickness of coating must be 3mm. Finish the surface with acrylic plaster, acrylic-siloxane or siloxane. Le caratteristiche dei materiali saranno quelle prescritte da Bifire s.r.l.. The characteristics of the materials will be those prescribed by Bifire s.r.l. 41
APPLICAZIONI ORIZZONTALI HORIZONTAL APPLICATIONS 43
CONTROSOFFITTO AQUAFIRE PER INTERNI INDOOR AQUAFIRE CEILING Fornitura e posa in opera soffitto per ambienti interni composta da orditura metallica e rivestimento in lastre di cemento alleggerito Aquafire. Supply and installation of ceiling for indoor environments comprised of metallic frames and covering in lightweight cement Aquafire boards. Realizzare la struttura metallica con profili in acciaio zincato con dimensioni pari a 28x30x0.6mm per le guide a "U", e 49x27x0.6mm per i montanti a C, posti ad interasse di 400mm e fissati al solaio con ganci in acciaio tassellati. Posare uno strato di lastre Aquafire in cemento alleggerito sp. 12,5mm lasciando fra una lastra e l altra 3-4mm fra i giunti, lato taglio a vista. Le lastre verranno fissate alla struttura con Viti Aquafire Star ad un un passo massimo di 150mm. Si indica una distanza dal bordo di c.a. mm 15. Spalmare uno strato di Finish sui giunti longitudinali e trasversali, largo 150mm. Annegare la rete per giunti Nastro Aquafire da 75mm nel rasante appena posato. Dopo 24 ore, lisciare la parete con Finish in un unica Build a metallic structure with 28x30x0.6 mm galvanized steel profiles for the "U" guides and 49x27x0.6 mm for C stanchions, placed at a centre distance of 400 mm and secured to the ceiling with steel anchored hooks. Install a layer of 12.5 mm thick lightweight cement Aquafire boards, leaving 3-4 mm between the joints of one slab and the next, cut side exposed. The boards will be affixed to the structure with Viti Aquafire Star screws at a maximum pitch of 150mm. A distance of about 15 mm is indicated from the edge. Spread a layer of Rasante Finish on the longitudinal and transversal joints 150 mm wide. Embed the 75 mm Nastro Aquafire mesh tape in the plaster as soon as it is spread. Once 24 hours have passed, smoothing the entire surface of the boards with Rasante Finish. mano Le caratteristiche dei materiali saranno quelle prescritte da Bifire s.r.l.. The characteristics of the materials will be those prescribed by Bifire s.r.l. 44
CONTR. AQUAFIRE ANTISFONDAMENTO PER INTERNI INDOOR AQUAFIRE BREAK-PROOF CEILING Fornitura e posa in opera di controsoffitto con funzione protettiva, denominato antisfondellamento, composta da orditura metallica e rivestimento in lastre di cemento alleggerito Aquafire. Realizzare la struttura metallica con profili in acciaio zincato con dimensioni pari a 75x40x0.6mm per le guide a "U", e 75x50x0.6mm per i montanti a C, posti ad interasse di 400mm e fissati al solaio con ganci in acciaio tassellati od opportuno sistema di pendiatura. Posare uno strato di lastre Aquafire in cemento alleggerito sp. 12,5mm lasciando fra una lastra e l altra 3-4mm fra i giunti, lato taglio a vista. Le lastre verranno fissate alla struttura con Viti Aquafire Star ad un un passo massimo di 150mm. Si indica una distanza dal bordo di c.a. mm 15. Spalmare uno strato di Finish sui giunti longitudinali e trasversali, largo 150mm. Annegare la rete per giunti Nastro Aquafire da 75mm nel rasante appena posato. Dopo 24 ore, lisciare la parete con Finish in un unica mano Supply and installation of false ceilings with protective function, called break-proof, comprised of metallic frames and covering in lightweight cement Aquafire boards. Build a metallic structure with 75x40x0.6 mm galvanized steel profiles for the "U" guides and 75x50x0.6 mm for C stanchions, placed at 400 mm intervals and secured to the ceiling with steel anchored hooks or an appropriate hanging system. Install a layer of 12.5 mm thick lightweight cement Aquafire boards, leaving 3-4 mm between the joints of one slab and the next, cut side exposed. The boards will be affixed to the structure with Viti Aquafire Star screws at a maximum pitch of 150mm. A distance of about 15 mm is indicated from the edge. Spread a layer of Finish on the longitudinal and transversal joints 150 mm wide. Embed the 75 mm Nastro Aquafire mesh tape in the plaster as soon as it is spread. Once 24 hours have passed, smoothing the entire surface of the boards with Finish. Le caratteristiche dei materiali saranno quelle prescritte da Bifire s.r.l.. The characteristics of the materials will be those prescribed by Bifire s.r.l. 45
RIQUALIFICAZIONE INTERNA CON CONTROSOFFITTO AQUAFIRE INDOOR FLOOR UPGRADING WITH AQUAFIRE CEILING Fornitura e posa in opera di soffitto per interni umidi composta da orditura metallica e rivestimento in lastre di cemento alleggerito Aquafire e isolante termico Vacunanex. Supply and installation of ceiling for humid indoor environments comprised of metallic frame and covering in Aquafire lightweight cement boards and Vacunanex thermal insulation. Realizzare la struttura metallica con profili in acciaio zincato con dimensioni pari a 28x30x0.6mm per le guide a "U", e 49x27x0.6mm per i montanti a C, posti ad interasse di 400mm e fissati al solaio con ganci in acciaio tassellati. Inserire nell intercapedine i pannelli isolanti sottovuoto Vacunanex sp.20mm così da garantire con il solo isolante una U=0.22 W/m 2 K Posare uno strato di lastre Aquafire in cemento alleggerito sp. 12,5mm lasciando fra una lastra e l altra 3-4mm fra i giunti, lato taglio a vista. Le lastre verranno fissate alla struttura con Viti Aquafire Star ad un passo massimo di 150mm. Si indica una distanza dal bordo di c.a. mm 15. Spalmare uno strato di Finish sui giunti longitudinali e trasversali, largo 150mm. Annegare la rete per giunti Nastro Aquafire da 75mm nel rasante appena posato. Dopo 24 ore, lisciare la parete con Finish in un unica mano Build a metallic structure with 28x30x0.6 mm galvanized steel profiles for the "U" guides and 49x27x0.6 mm for C stanchions, placed at a centre distance of 400 mm and secured to the ceiling with steel anchored hooks. Insert the 20 mm thick Vacunanex insulating vacuum panels into the cavity in order to guarantee U=0.22 W/m2K with just the insulation Install a layer of 12.5 mm thick lightweight cement Aquafire boards, leaving 3-4 mm between the joints of one slab and the next, cut side exposed. The boards will be affixed to the structure with Viti Aquafire Star screws at a maximum pitch of 150mm. A distance of about 15 mm is indicated from the edge. Spread a layer of Finish on the longitudinal and transversal joints 150 mm wide. Embed the 75 mm Nastro Aquafire mesh tape in the plaster as soon as it is spread. Once 24 hours have passed, smoothing the entire surface of the boards with Finish. U= 0,22 W/m 2 K Le caratteristiche dei materiali saranno quelle prescritte da Bifire s.r.l.. The characteristics of the materials will be those prescribed by Bifire s.r.l. 46
RIQUALIFICAZIONE ESTERNA CON CONTROSOFFITTO AQUAFIRE OUTDOOR FLOOR UPGRADING WITH AQUAFIRE CEILING Fornitura e posa in opera di soffitto per esterni composta da orditura metallica e rivestimento in lastre di cemento alleggerito Aquafire e isolante termico Vacunanex. Realizzare la struttura metallica con profili in acciaio zincato con dimensioni pari a 28x30x1.0mm per le guide a "U", e 49x27x1.0mm per i montanti a C, posti ad interasse di 400mm e fissati al solaio con ganci in acciaio tassellati. Inserire nell intercapedine i pannelli isolanti sottovuoto Vacunanex sp.20mm così da garantire con il solo isolante una U=0.22 W/m 2 K. Posare uno strato di lastre Aquafire in cemento alleggerito sp. 12,5mm lasciando fra una lastra e l altra 3-4mm fra i giunti, lato taglio a vista. Le lastre verranno fissate alla struttura con Viti Aquafire Star ad un passo massimo di 150mm. Si indica una distanza dal bordo di c.a. mm 15. Spalmare uno strato di Rasante Aquafire sui giunti longitudinali e trasversali, largo 150mm. Annegare la rete per giunti Nastro Aquafire da 75mm nel rasante appena posato; Passato il tempo di asciugatura di 12 ore, spalmare uno strato di Rasante Aquafire sull intera superficie della lastra con frattazzo dentato in acciaio. Annegare la Rete Aquafire nel rasante appena posato, avendo cura di nasconderla completamente, lavorando con il lato liscio del frattazzo dentato. A questo punto lo spessore finale della rasatura deve essere di 3mm. Finire la superficie con intonachino acrilico, acrilsilossanico o silossanico. Supply and installation of ceiling for outdoor environments comprised of metallic frame and covering in Aquafire lightweight cement boards and Vacunanex thermal insulation. Build a metallic structure with 28x30x1.0 mm galvanized steel profiles for the "U" guides and 49x27x1.0 mm for C stanchions, placed at a centre distance of 400 mm and secured to the ceiling with steel anchored hooks. Insert the 20 mm thick Vacunanex insulating vacuum panels into the cavity in order to guarantee U=0.22 W/m2K with just the insulation. Install a layer of 12.5 mm thick lightweight cement Aquafire boards, leaving 3-4 mm between the joints of one slab and the next, cut side exposed. The boards will be affixed to the structure with Viti Aquafire Star screws at a maximum pitch of 150mm. A distance of about 15 mm is indicated from the edge. Spread a layer of Rasante Aquafire coat on the longitudinal and transversal joints 150 mm wide. Embed the 75 mm Nastro Aquafire mesh for joints in the plaster as soon as it is spread; Once 12 hours have passed after filling the joints, spread a layer of Rasante Aquafire on the entire surface of the boards with a notched trowel steel. Embed the Rete Aquafire mesh in the cement coat which has just been spread, taking care to hide it completely, working with the smooth side of the trowel steel. At this point the final thickness of coating must be 3mm. Finish the surface with acrylic plaster, acrylic-siloxane or siloxane. U= 0,22 W/m 2 K Le caratteristiche dei materiali saranno quelle prescritte da Bifire s.r.l.. The characteristics of the materials will be those prescribed by Bifire s.r.l. 47
CONTROSOFFITTO AQUAFIRE PER ESTERNI OUTDOOR AQUAFIRE CEILING Fornitura e posa in opera di soffitto per esterni composto da orditura metallica e rivestimento in lastre di cemento alleggerito Aquafire. Supply and installation of outdoor ceiling comprised of metallic frames and covering in lightweight cement Aquafire boards. Realizzare la struttura metallica principale con profili in acciaio zincato con dimensioni pari a 28x30x1.0mm per le guide a "U", e 49x27x1.0mm per i montanti a C posti ad interasse opportuno e con adeguato sistema di pendi natura. Build a primary metallic structure with 28x30x1.0 mm galvanized steel profiles for the "U" guides and 49x27x1.0 mm for C stanchions, placed at appropriate intervals and with an adequate hanging system. Build a secondary structure with 49x27x1.0 mm C stanchions placed at a centre distance of 400 mm and constrained to the primary structure with appropriate hooks. Realizzare la struttura secondaria con montanti a C 49x27x1.0mm posti ad interasse di 400mm e vincolati alla struttura primaria con appositi ganci. Posare uno strato di lastre Aquafire in cemento alleggerito sp. 12,5mm lasciando fra una lastra e l altra 3-4mm fra i giunti, lato taglio a vista. Le lastre verranno fissate alla struttura con Viti Aquafire Star ad un un passo massimo di 150mm. Si indica una distanza dal bordo di c.a. mm 15. Spalmare uno strato di Rasante Aquafire sui giunti longitudinali e trasversali, largo 150mm. Annegare la rete per giunti Nastro Aquafire da 75mm nel rasante appena posato; Passato il tempo di asciugatura di 12 ore, spalmare uno strato di Rasante Aquafire sull intera superficie della lastra con frattazzo dentato in acciaio. Annegare la Rete Aquafire nel rasante appena posato, avendo cura di nasconderla completamente, lavorando con il lato liscio del frattazzo dentato. A questo punto lo spessore finale della rasatura deve essere di 3mm. Finire la superficie con intonachino acrilico, acrilsilossanico o silossanico. Install a layer of 12.5 mm thick lightweight cement Aquafire boards, leaving 3-4 mm between the joints of one slab and the next, cut side exposed. The boards will be affixed to the structure with Viti Aquafire Star screws at a maximum pitch of 150mm. A distance of about 15 mm is indicated from the edge. Spread a layer of Rasante Aquafire coat on the longitudinal and transversal joints 150 mm wide. Embed the 75 mm Nastro Aquafire mesh for joints in the plaster as soon as it is spread; Once 12 hours have passed after filling the joints, spread a layer of Rasante Aquafire on the entire surface of the boards with a notched trowel steel. Embed the Rete Aquafire mesh in the cement coat which has just been spread, taking care to hide it completely, working with the smooth side of the trowel steel. At this point the final thickness of coating must be 3mm. Finish the surface with acrylic plaster, acrylic-siloxane or siloxane. Le caratteristiche dei materiali saranno quelle prescritte da Bifire s.r.l.. The characteristics of the materials will be those prescribed by Bifire s.r.l. 48
NOTE 49
NOTE 50
Consultate il nostro sito: Via Lavoratori dell Autobianchi, 1 20832 Desio (MB), Italy Tel:+39 0362 364570 Fax +39 0362 334134 e-mail: bifire@bifire.it Cod. A01770175 edizione 05.2013