CINGHIE - V BELT POWER

CINGHIE - V BELT POWER Cinghie trapezoidali classiche... Pag. 2-10 Classical V belts / Z A B C D E Cinghie trapezoidali strette... Pag. 11-17 Conventional wrapped narrow V belts / SPZ SPA SPB SPC 3V 5V 8V Cinghie multiband... Pag. 18-18 Multiband Belts / HA HB HC HD SPA SPB SPC 3V 5V 8V Cinghie esagonali... Pag. 19-22 Double V belts / AA BB CC Cinghie dentellate classiche... Pag. 23-26 Classical Raw Edge / AX BX CX Cinghie dentellate strette... Pag. 26-28 Narrow Raw Edge / SPZX SPAX SPBX SPCX Cinghie piane... Pag. 29-30 Flat belts Cinghie POLY-V... Pag. 31-33 PolyV ribbed belts / PJ PK PL PM 1 Cinghie per Variatori... Pag. 34-36 Variable speed belts / 17x6 22x8 28x8 37x10 47x12 55x16 Cinghie e manicotti dentati... Pag. 37-50 Timing belts & Sleeves / MXL XL L H XH XXH Cinghie e manicotti dentati HTD... Pag. 51-63 Timing belts & Sleeves HTD / 3M 5M 8M 14M Cinghie e manicotti dentati doppia dentatura... Pag. 64-68 Double Side Timing belts & Sleeves / DL DH 8MDD 14MDD Cinghie in poliuretano a metraggio... Pag. 69-71 Open end Polyurethane belts / T5 T10 T20 AT5 AT10 AT20 L H HTD 5-8-14M RPP 8-14M Paz Cinghie e manicotti dentati in poliuretano... Pag. 72-80 Polyurethane Timing belts & Sleeves / T2.5 T5 T10 AT5 AT10 DT5 DT10 Cinghie termosaldabili trapezoidali e tonde... Pag. 81-84 Urethane V & Round Belts Cinghie speciali... Pag. 85-85 Special Belts

CINGHIE TRAPEZOIDALI CLASSICHE POWER, 2 CINGHIE TRAPEZOIDALI CLASSICHE

CONVENTIONAL V-BELT POWER 3 CONVENTIONAL V-BELT POWER

CINGHIE TRAPEZOIDALI CLASSICHE CONVENTIONAL V-BELT POWER CINGHIE TRAPEZOIDALI CLASSICHE - CONVENTIONAL V-BELT POWER 4 SEZIONE Z - SECTION Z Int. (mm) Li (mm) List / Z 14 355 5,09 Z 16 410 5,90 Z 17 432 6,21 Z 17 1/4 445 6,34 Z 17 1/2 440 6,39 Z 18 460 6,62 Z 19 480 6,90 Z 19 1/2 500 7,18 Z 20 508 7,30 Z 20 1/2 520 7,46 Z 21 533 7,65 Z 21 1/4 540 7,78 Z 21 3/4 555 7,99 Z 22 560 8,06 Z 22 1/4 565 8,11 Z 23 585 8,39 Z 23 3/4 605 8,70 Z 24 610 8,77 Z 25 635 9,12 Z 25 1/2 650 9,33 Z 26 660 9,49 Z 27 685 9,83 Z 27 1/2 698 9,84 Z 28 710 9,85 Z 28 1/2 725 9,86 Z 29 730 9,87 Z 29 1/2 750 10,13 Z 30 762 10,31 Z 30 1/2 775 10,49 Z 30 3/4 785 10,61 Z 31 790 10,69 Z 31 1/2 800 10,81 Z 32 815 11,02 Z 32 1/2 827 11,19 Z 33 840 11,37 Z 33 1/2 852 11,38 Z 34 865 11,39 Z 34 1/4 870 11,40 Z 34 1/2 876 11,42 SEZIONE Z - SECTION Z Int. (mm) Li (mm) List / Z 35 890 11,43 Z 35 1/2 900 11,49 Z 36 915 11,69 Z 36 3/4 935 11,97 Z 37 940 12,02 Z 38 965 12,32 Z 38 1/4 975 12,46 Z 38 1/2 978 12,50 Z 39 1000 12,77 Z 40 1016 12,99 Z 40 1/2 1030 13,15 Z 41 1040 13,17 Z 41 1/2 1050 13,18 Z 42 1070 13,19 Z 43 1090 13,20 Z 43 1/4 1100 13,23 Z 44 1120 13,37 Z 45 1143 13,63 Z 46 1180 14,07 Z 47 1194 14,38 Z 48 1225 14,62 Z 49 1245 14,85 Z 50 1270 15,16 Z 51 1300 15,53 Z 52 1320 15,76 Z 53 1346 16,07 Z 54 1371 16,35 Z 55 1400 16,72 Z 56 1422 16,98 Z 57 1450 17,31 Z 59 1499 17,88 Z 59 1/2 1515 18,09 Z 60 1520 18,14 Z 61 1549 18,48 Z 62 1575 18,79 Z 63 1600 19,11 Z 64 1620 19,33 Z 65 1651 19,70 Z 66 1675 19,98 SEZIONE Z - SECTION Z Int. (mm) Li (mm) List / Z 67 1702 20,33 Z 68 1/2 1735 20,71 Z 69 1750 20,89 Z 71 1803 21,51 Z 72 1829 21,83 SEZIONE A - SECTION A Int. (mm) Li (mm) List / A 15 382 5,78 A 16 407 6,13 A 17 432 6,53 A 18 457 6,89 A 19 480 7,26 A 20 508 7,68 A 21 535 8,08 A 21 1/4 541 8,18 A 21 3/4 552 8,34 A 22 560 8,47 A 23 587 8,87 A 23 1/2 600 9,06 A 24 610 9,22 A 25 637 9,62 A 25 1/2 647 9,78 A 26 660 9,98 A 26 1/2 670 10,14 A 27 686 10,38 A 28 710 10,74 A 29 737 11,13 A 29 1/2 750 11,33 A 30 762 11,52 A 30 1/2 775 11,53 A 31 787 11,55 A 31 1/2 800 11,56 A 32 813 11,57 A 32 1/2 825 11,58 A 33 838 11,59 A 33 1/4 847 11,71

CINGHIE TRAPEZOIDALI CLASSICHE CONVENTIONAL V-BELT POWER SEZIONE A - SECTION A Int. (mm) Li (mm) List / A 33 1/2 850 11,72 A 34 863 11,73 A 34 1/2 875 11,74 A 35 890 11,75 A 36 914 11,96 A 37 940 12,30 A 37 1/2 953 12,47 A 38 965 12,61 A 38 1/2 978 12,79 A 39 990 12,95 A 40 1016 13,29 A 40 1/2 1030 13,47 A 41 1041 13,61 A 42 1067 13,94 A 43 1092 14,29 A 43 1/2 1105 14,46 A 44 1120 14,66 A 44 1/2 1132 14,80 A 45 1143 14,94 A 46 1168 15,28 A 47 1194 15,63 A 48 1220 15,96 A 49 1250 16,36 A 50 1270 16,62 A 51 1300 17,01 A 51 1/2 1307 17,10 A 52 1320 17,27 A 52 1/2 1337 17,50 A 53 1346 17,61 A 53 1/4 1355 17,72 A 53 3/4 1365 17,87 A 54 1372 17,95 A 55 1400 18,32 A 56 1422 18,61 A 57 1450 18,98 A 58 1475 19,29 A 59 1500 19,62 A 60 1525 19,94 A 61 1550 20,28 SEZIONE A - SECTION A Int. (mm) Li (mm) List / A 62 1575 20,29 A 63 1600 20,30 A 64 1625 20,33 A 65 1650 20,35 A 66 1676 20,37 A 67 1700 20,41 A 68 1725 20,58 A 69 1750 20,89 A 70 1775 21,18 A 71 1800 21,49 A 72 1825 21,77 A 73 1854 22,14 A 74 1880 22,44 A 75 1905 22,73 A 76 1930 23,05 A 77 1956 23,35 A 78 1980 23,64 A 79 2000 23,87 A 80 2032 24,26 A 81 2060 24,60 A 82 2083 24,86 A 83 2100 25,07 A 83 1/2 2120 25,29 A 84 2134 25,48 A 85 2160 25,79 A 86 2187 26,10 A 87 2212 26,42 A 88 2240 26,72 A 89 2267 27,06 A 90 2286 27,29 A 91 2311 27,58 A 92 2337 27,89 A 93 2360 28,18 A 94 2388 28,51 A 95 2413 28,79 A 96 2438 29,11 A 97 2464 29,42 A 97 1/2 2476 29,55 A 98 2490 29,73 SEZIONE A - SECTION A Int. (mm) Li (mm) List / A 99 2515 30,01 A 100 2540 30,33 A 102 2591 30,92 A 103 2616 31,23 A 104 2641 31,51 A 105 2667 31,83 A 107 2718 32,45 A 108 2743 32,73 A 109 2768 33,05 A 110 2800 33,42 A 112 2845 33,96 A 113 2870 34,27 A 115 2920 34,86 A 116 2946 35,18 A 118 3000 35,79 A 120 3048 36,40 A 122 3099 36,99 A 124 3150 37,58 A 126 3200 38,21 A 127 3225 38,49 A 128 3250 38,80 A 130 3302 39,40 A 132 3350 39,99 A 134 3404 40,62 A 136 3454 41,21 A 138 3505 41,84 A 140 3550 42,38 A 142 3606 43,03 A 144 3658 43,65 A 146 3710 44,27 A 147 3734 44,56 A 148 3759 44,86 A 150 3810 45,47 A 155 3937 46,99 A 158 4000 47,75 A 162 4115 49,12 A 167 4250 50,73 A 173 4394 52,43 A 177 4500 53,71 5 CINGHIE TRAPEZOIDALI CLASSICHE - CONVENTIONAL V-BELT POWER

CINGHIE TRAPEZOIDALI CLASSICHE CONVENTIONAL V-BELT POWER CINGHIE TRAPEZOIDALI CLASSICHE - CONVENTIONAL V-BELT POWER 6 SEZIONE A - SECTION A Int. (mm) Li (mm) List / A 180 4572 54,56 A 187 4750 56,69 A 197 5004 59,72 A 210 5334 63,66 A 217 5477 65,37 SEZIONE B - SECTION B Int. (mm) Li (mm) List / B 22 1/2 570 11,99 B 23 587 12,36 B 24 612 12,86 B 24 1/2 625 13,14 B 25 637 13,39 B 26 660 13,89 B 27 686 13,93 B 28 710 14,04 B 29 737 14,15 B 29 1/2 750 14,26 B 30 762 14,36 B 30 1/2 775 14,49 B 31 787 14,71 B 32 800 14,96 B 32 1/4 822 15,38 B 32 1/2 829 15,52 B 33 838 15,68 B 33 1/2 850 15,70 B 34 863 15,72 B 34 1/2 875 15,74 B 34 3/4 880 15,82 B 35 889 15,98 B 35 1/2 900 16,19 B 35 3/4 907 16,30 B 36 917 16,48 B 36 3/4 937 16,86 B 37 942 16,93 B 38 965 17,34 B 38 1/2 978 17,58 SEZIONE B - SECTION B Int. (mm) Li (mm) List / B 39 990 17,79 B 39 1/2 1002 18,00 B 40 1016 18,27 B 40 1/2 1028 18,49 B 41 1040 18,69 B 42 1067 19,18 B 42 1/2 1079 19,40 B 43 1090 19,60 B 44 1120 20,14 B 44 1/4 1127 20,27 B 45 1142 20,54 B 46 1168 21,00 B 46 1/2 1180 21,21 B 46 3/4 1187 21,34 B 47 1194 21,47 B 47 1/4 1200 21,58 B 47 1/2 1207 21,72 B 48 1220 21,92 B 49 1250 22,49 B 50 1275 22,92 B 51 1300 23,37 B 52 1320 23,74 B 53 1350 24,28 B 53 1/2 1360 24,46 B 54 1372 24,68 B 55 1400 25,19 B 55 1/2 1412 25,39 B 56 1422 25,55 B 57 1450 26,06 B 58 1473 26,49 B 59 1500 26,97 B 60 1525 27,42 B 61 1550 27,87 B 62 1575 28,33 B 63 1600 28,76 B 64 1625 29,21 B 64 1/2 1637 29,42 B 65 1650 29,67 B 66 1676 30,14 SEZIONE B - SECTION B Int. (mm) Li (mm) List / B 66 1/4 1682 30,25 B 66 1/2 1692 30,41 B 67 1700 30,57 B 67 1/4 1712 30,78 B 68 1725 31,03 B 69 1750 31,48 B 69 1/2 1762 31,69 B 70 1775 31,90 B 71 1800 32,36 B 72 1829 32,90 B 73 1850 33,26 B 74 1880 33,79 B 75 1905 34,25 B 76 1930 34,70 B 77 1956 35,15 B 78 1981 35,61 B 79 2000 35,96 B 80 2032 36,55 B 81 2060 37,02 B 82 2083 37,45 B 83 2108 37,91 B 84 2134 38,36 B 85 2160 38,84 B 86 2187 39,32 B 87 2215 39,83 B 88 2240 40,28 B 89 2261 40,65 B 90 2286 41,10 B 91 2312 41,56 B 92 2337 42,01 B 93 2360 42,44 B 94 2388 42,95 B 95 2413 43,37 B 96 2438 43,83 B 97 2465 44,31 B 97 1/2 2477 44,55 B 98 2500 44,95 B 99 2515 45,22 B 100 2540 45,67

CINGHIE TRAPEZOIDALI CLASSICHE CONVENTIONAL V-BELT POWER SEZIONE B - SECTION B Int. (mm) Li (mm) List / B 101 2566 46,15 B 102 2600 46,73 B 103 2616 47,03 B 104 2641 47,49 B 105 2667 47,96 B 106 2700 48,55 B 107 2718 48,87 B 108 2750 49,45 B 110 2800 50,34 B 112 2845 51,16 B 112 1/2 2857 51,38 B 113 2870 51,59 B 114 2900 52,15 B 115 2921 52,52 B 116 2950 53,03 B 118 3000 53,94 B 120 3048 54,79 B 122 3100 55,73 B 124 3150 56,64 B 125 3175 57,09 B 126 3200 57,54 B 127 3227 58,02 B 128 3250 58,45 B 130 3302 59,38 B 131 3327 59,81 B 132 3350 60,23 B 133 3378 60,74 B 134 3407 61,25 B 135 3429 61,65 B 136 3450 62,02 B 138 3505 63,01 B 140 3550 63,84 B 142 3607 64,85 B 144 3658 65,78 B 146 3709 66,69 B 147 3737 67,20 B 148 3750 67,44 B 151 3850 69,23 B 152 3861 69,41 SEZIONE B - SECTION B Int. (mm) Li (mm) List / B 154 3912 70,34 B 155 3950 71,01 B 157 3987 71,68 B 158 4000 71,92 B 160 4064 73,07 B 161 4087 73,49 B 162 4115 74,00 B 163 4142 74,48 B 165 4200 75,52 B 167 4250 76,43 B 168 4267 76,72 B 169 4292 77,18 B 173 4394 79,01 B 175 4450 80,01 B 177 4500 80,91 B 180 4572 82,22 B 186 4727 84,99 B 187 4750 85,42 B 188 4777 85,89 B 190 4826 86,78 B 192 4877 87,69 B 195 4953 86,52 B 197 5000 87,35 B 200 5080 88,75 B 201 5105 89,19 B 204 5182 90,54 B 208 5285 92,33 B 210 5334 93,18 B 212 5385 94,09 B 214 5436 94,98 B 217 5507 96,22 B 220 5588 97,61 B 221 5615 98,11 B 223 5664 98,96 B 224 5690 99,40 B 225 5715 99,85 B 228 5792 101,20 B 229 5816 101,61 B 232 5893 102,96 SEZIONE B - SECTION B Int. (mm) Li (mm) List / B 237 6020 115,27 B 240 6096 116,72 B 248 6300 120,60 B 249 6325 121,09 B 253 6426 123,02 B 255 6477 124,02 B 259 6579 125,94 B 265 6730 128,84 B 270 6858 131,28 B 276 7010 134,21 B 280 7112 136,17 B 285 7240 138,61 B 300 7620 145,89 B 315 8000 153,15 B 330 8382 160,49 B 345 8763 167,76 B 360 9145 175,08 B 361 9170 175,56 B 366 9296 177,98 B 374 9500 181,87 B 394 10008 191,61 B 428 1/2 10885 208,40 B 433 11000 210,59 B 449 11400 218,26 B 472 11990 229,53 B 473 12014 230,02 B 488 12400 237,41 B 512 13000 248,88 B 551 13995 267,94 B 553 14046 268,90 B 583 14808 283,50 B 612 15545 297,62 7 CINGHIE TRAPEZOIDALI CLASSICHE - CONVENTIONAL V-BELT POWER

CINGHIE TRAPEZOIDALI CLASSICHE CONVENTIONAL V-BELT POWER CINGHIE TRAPEZOIDALI CLASSICHE - CONVENTIONAL V-BELT POWER 8 SEZIONE C - SECTION C Int. (mm) Li (mm) List / C 33 3/4 857 23,33 C 39 990 26,81 C 39 3/4 1013 27,43 C 41 1041 28,19 C 42 1067 28,89 C 43 1090 29,52 C 44 1120 30,34 C 45 1143 30,94 C 46 1168 31,62 C 47 1194 32,32 C 48 1220 33,05 C 49 1250 33,85 C 51 1295 35,06 C 52 1320 35,73 C 53 1350 36,56 C 54 1370 37,09 C 55 1400 37,91 C 56 1425 38,59 C 57 1448 39,21 C 58 1473 39,90 C 58 1/2 1486 40,23 C 59 1500 40,62 C 60 1524 41,27 C 61 1550 41,97 C 62 1574 42,63 C 62 1/4 1583 42,87 C 63 1600 43,33 C 65 1650 44,68 C 66 1676 45,38 C 67 1702 46,08 C 68 1727 46,76 C 69 1753 47,47 C 70 1778 48,15 C 71 1804 48,85 C 72 1829 49,52 C 73 1854 50,20 C 74 1880 50,90 C 75 1905 51,58 C 76 1925 52,13 SEZIONE C - SECTION C Int. (mm) Li (mm) List / C 78 1981 53,63 C 79 2006 54,31 C 80 2032 55,02 C 81 2057 55,68 C 82 2082 56,37 C 83 2108 57,07 C 84 2134 57,79 C 85 2159 58,47 C 86 2184 59,15 C 87 2208 59,78 C 88 2235 60,52 C 89 2260 61,20 C 90 2286 61,91 C 91 2311 62,59 C 92 2336 63,27 C 93 2360 63,91 C 94 2388 64,67 C 95 2413 65,34 C 96 2438 66,02 C 97 2462 66,67 C 98 2489 67,40 C 99 2525 68,36 C 100 2540 68,77 C 101 2560 69,31 C 102 2591 70,16 C 104 2642 71,54 C 105 2667 72,21 C 106 2692 72,89 C 108 2750 74,47 C 110 2800 75,82 C 111 2818 76,30 C 112 2845 77,03 C 112 1/2 2857 77,37 C 114 2896 78,41 C 115 2921 79,09 C 116 2950 79,88 C 117 2971 80,44 C 118 3000 81,24 C 120 3048 82,54 SEZIONE C - SECTION C Int. (mm) Li (mm) List / C 122 3100 83,95 C 124 3150 85,30 C 126 3200 86,66 C 128 3250 88,01 C 130 3302 89,41 C 132 3350 90,72 C 134 3404 92,17 C 136 3456 93,57 C 138 3505 94,91 C 140 3550 96,12 C 142 3607 97,66 C 144 3658 99,05 C 145 3682 99,69 C 146 3708 100,40 C 147 3733 101,08 C 148 3750 101,53 C 150 3810 103,18 C 152 3860 104,51 C 153 3902 105,65 C 154 3912 105,94 C 158 4000 108,30 C 160 4064 110,05 C 162 4115 111,42 C 165 4193 113,53 C 166 4216 114,17 C 168 4267 115,54 C 170 4318 116,92 C 173 4394 118,97 C 175 4445 120,36 C 177 4500 121,86 C 178 4522 122,44 C 180 4572 123,79 C 185 4699 127,25 C 187 4750 128,63 C 189 4800 129,99 C 193 4900 132,69 C 195 4953 134,13 C 197 5004 135,50 C 200 5080 137,56

CINGHIE TRAPEZOIDALI CLASSICHE CONVENTIONAL V-BELT POWER SEZIONE C - SECTION C Int. (mm) Li (mm) List / C 204 5182 140,31 C 208 5285 143,10 C 210 5334 144,43 C 212 5384 145,78 C 215 5461 147,86 C 216 5486 148,54 C 218 5537 149,95 C 220 5588 151,32 C 222 5638 152,68 C 223 5664 153,38 C 224 5690 154,08 C 225 5715 154,75 C 228 5792 156,84 C 230 5842 158,19 C 236 5995 162,32 C 238 6045 163,68 C 240 6096 176,85 C 248 6300 182,79 C 250 6350 184,24 C 255 6477 187,92 C 260 6604 191,60 C 261 6629 192,33 C 265 6730 195,25 C 268 6807 197,49 C 269 6833 198,23 C 270 6858 198,96 C 276 7010 203,36 C 280 7112 206,32 C 285 7240 210,06 C 297 7544 218,87 C 300 7620 221,08 C 303 7696 223,28 C 314 7975 238,11 C 315 8000 238,85 C 316 8026 239,63 C 330 8382 250,28 C 336 8535 254,84 C 345 8763 261,64 C 348 8839 263,91 SEZIONE C - SECTION C Int. (mm) Li (mm) List / C 350 8890 265,45 C 352 8940 266,92 C 354 8992 268,50 C 360 9145 273,06 C 394 10008 298,83 C 420 10668 318,54 C 424 10770 321,58 C 440 11176 333,69 C 452 11480 342,76 C 464 11785 351,89 C 480 12192 364,02 C 482 12243 365,54 C 500 12700 379,19 SEZIONE D - SECTION D Int. (mm) Li (mm) List / D 93 2362 116,26 D 98 2490 122,56 D 101 2565 126,26 D 104 2641 129,99 D 110 2795 137,58 D 118 3000 147,67 D 120 3048 150,03 D 124 3150 155,04 D 125 3175 156,28 D 128 3251 160,03 D 135 3429 168,78 D 136 3454 170,02 D 137 3480 171,30 D 140 3555 174,98 D 144 3658 180,06 D 148 3760 185,07 D 150 3810 187,53 D 152 3861 190,05 D 154 3912 192,56 D 158 4013 197,53 D 162 4115 202,56 SEZIONE D - SECTION D Int. (mm) Li (mm) List / D 167 4241 208,75 D 170 4318 212,55 D 173 4394 216,28 D 177 4496 221,31 D 180 4572 225,03 D 187 4750 233,82 D 192 4877 240,06 D 195 4953 243,81 D 197 5004 246,29 D 204 5182 255,09 D 205 5208 256,34 D 207 5259 258,85 D 210 5334 262,56 D 223 5664 278,79 D 225 5715 281,31 D 236 5995 295,10 D 238 6045 297,54 D 240 6096 300,06 D 248 6300 310,09 D 250 6350 312,56 D 255 6477 318,81 D 260 6604 325,07 D 266 6756 332,54 D 270 6858 337,58 D 280 7112 350,06 D 282 7163 352,58 D 285 7240 356,37 D 295 7493 368,83 D 298 7570 372,60 D 300 7620 375,07 D 314 7975 392,54 D 316 8026 395,05 D 326 8280 407,56 D 330 8382 412,57 D 335 8509 418,83 D 345 8763 431,34 D 354 8991 442,54 D 360 9145 450,14 D 374 9500 467,61 9 CINGHIE TRAPEZOIDALI CLASSICHE - CONVENTIONAL V-BELT POWER

CINGHIE TRAPEZOIDALI CLASSICHE CONVENTIONAL V-BELT POWER SEZIONE D - SECTION D Int. (mm) Li (mm) List / D 385 9780 481,40 D 390 9905 487,54 D 394 10008 492,62 D 420 10668 525,11 D 441 11200 551,29 D 450 11430 562,60 D 460 11685 575,16 D 480 12192 600,10 D 500 12700 625,13 D 540 13716 675,13 D 570 14478 712,65 D 600 15240 750,16 SEZIONE E - SECTION E Int. (mm) Li (mm) List / E 456 11582 921,66 E 460 11684 929,77 E 470 11938 949,99 E 475 12065 960,10 E 480 12190 970,03 E 492 12497 994,47 E 520 13208 1051,06 CINGHIE TRAPEZOIDALI CLASSICHE - CONVENTIONAL V-BELT POWER 10 SEZIONE E - SECTION E Int. (mm) Li (mm) List / E 180 4575 364,07 E 197 5000 397,87 E 210 5335 424,55 E 226 5740 456,76 E 240 6096 485,09 E 245 6223 495,20 E 248 6300 501,31 E 255 6477 515,42 E 270 6858 545,75 E 285 7240 576,13 E 300 7620 606,38 E 316 8026 638,67 E 330 8382 667,00 E 345 8763 697,32 E 360 9145 727,73 E 392 9957 792,35 E 394 10008 796,39 E 396 10058 800,39 E 416 10566 840,79 E 420 10668 848,93 E 441 11200 891,26 E 453 11506 915,60

CINGHIE TRAPEZOIDALI STRETTE SP POWER, 11 CINGHIE TRAPEZOIDALI STRETTE

WRAPPED NARROW SECTION V-BELT POWER 12 WRAPPED NARROW SECTION V-BELT POWER

CINGHIE TRAPEZOIDALI STRETTE SP CONVENTIONAL WRAPPED NARROW SEZIONE SPZ - SECTION SPZ Est. (mm) Le (mm) List / SPZ 512 525 7,11 SPZ 562 575 7,79 SPZ 587 600 8,11 SPZ 607 620 8,40 SPZ 612 625 8,46 SPZ 630 643 8,69 SPZ 637 650 8,78 SPZ 662 675 9,14 SPZ 670 683 9,26 SPZ 687 700 9,46 SPZ 710 723 9,50 SPZ 722 735 9,56 SPZ 737 750 9,58 SPZ 750 763 9,74 SPZ 762 775 9,90 SPZ 772 785 9,94 SPZ 787 800 9,96 SPZ 800 813 9,98 SPZ 812 825 10,14 SPZ 825 838 10,29 SPZ 837 850 10,45 SPZ 850 863 10,62 SPZ 862 875 10,75 SPZ 875 888 10,91 SPZ 887 900 11,07 SPZ 900 913 11,23 SPZ 912 925 11,36 SPZ 922 935 11,50 SPZ 937 950 11,69 SPZ 950 963 11,85 SPZ 957 970 11,92 SPZ 962 975 11,98 SPZ 987 1000 12,30 SPZ 1000 1013 12,45 SPZ 1012 1025 12,59 SPZ 1024 1037 12,75 SPZ 1037 1050 12,91 SPZ 1047 1060 13,01 SPZ 1060 1073 13,18 SEZIONE SPZ - SECTION SPZ Est. (mm) Le(mm) List / SPZ 1077 1090 13,39 SPZ 1087 1100 13,52 SPZ 1112 1125 13,81 SPZ 1120 1133 13,92 SPZ 1137 1150 14,14 SPZ 1147 1160 14,25 SPZ 1150 1163 14,30 SPZ 1162 1175 14,43 SPZ 1180 1193 14,68 SPZ 1187 1200 14,75 SPZ 1202 1215 14,94 SPZ 1212 1225 15,04 SPZ 1237 1250 15,37 SPZ 1250 1263 15,53 SPZ 1262 1275 15,66 SPZ 1270 1283 15,77 SPZ 1280 1293 15,90 SPZ 1287 1300 15,98 SPZ 1312 1325 16,28 SPZ 1314 1327 16,30 SPZ 1320 1333 16,38 SPZ 1337 1350 16,59 SPZ 1347 1360 16,70 SPZ 1362 1375 16,89 SPZ 1387 1400 17,20 SPZ 1400 1413 17,37 SPZ 1412 1425 17,50 SPZ 1437 1450 17,82 SPZ 1450 1463 17,96 SPZ 1462 1475 18,11 SPZ 1487 1500 18,44 SPZ 1500 1513 18,60 SPZ 1512 1525 18,73 SPZ 1537 1550 19,05 SPZ 1562 1575 19,34 SPZ 1587 1600 19,66 SPZ 1600 1613 19,82 SPZ 1612 1625 19,98 SPZ 1637 1650 20,27 SEZIONE SPZ - SECTION SPZ Est. (mm) Le (mm) List / SPZ 1650 1663 20,43 SPZ 1662 1675 20,60 SPZ 1687 1700 20,89 SPZ 1700 1713 21,05 SPZ 1737 1750 21,50 SPZ 1750 1763 21,66 SPZ 1762 1775 21,82 SPZ 1787 1800 22,12 SPZ 1800 1813 22,27 SPZ 1812 1825 22,43 SPZ 1837 1850 22,72 SPZ 1850 1863 22,89 SPZ 1862 1875 23,05 SPZ 1880 1893 23,26 SPZ 1887 1900 23,34 SPZ 1900 1913 23,50 SPZ 1937 1950 23,95 SPZ 1950 1963 24,12 SPZ 1962 1975 24,28 SPZ 1987 2000 24,57 SPZ 2000 2013 24,73 SPZ 2019 2032 24,97 SPZ 2037 2050 25,19 SPZ 2062 2075 25,50 SPZ 2087 2100 25,79 SPZ 2120 2133 26,22 SPZ 2137 2150 26,41 SPZ 2187 2200 27,02 SPZ 2240 2253 27,69 SPZ 2262 2275 27,96 SPZ 2287 2300 28,25 SPZ 2360 2373 29,16 SPZ 2437 2450 30,12 SPZ 2487 2500 30,73 SPZ 2500 2513 30,89 SPZ 2580 2593 31,85 SPZ 2650 2663 32,73 SPZ 2687 2700 33,19 SPZ 2720 2733 33,59 13 CINGHIE TRAPEZOIDALI STRETTE SP - WRAPPED NARROW SECTION V-BELT POWER

CINGHIE TRAPEZOIDALI STRETTE SP CONVENTIONAL WRAPPED NARROW CINGHIE TRAPEZOIDALI STRETTE SP - WRAPPED NARROW SECTION V-BELT POWER 14 SEZIONE SPZ - SECTION SPZ Est. (mm) Le (mm) List / SPZ 2800 2813 34,57 SPZ 3000 3013 37,02 SPZ 3150 3163 38,87 SPZ 3350 3363 41,32 SPZ 3550 3563 43,77 SEZIONE SPA - SECTION SPA Est. (mm) Le (mm) List / SPA 647 665 10,81 SPA 707 725 11,80 SPA 732 750 12,19 SPA 757 775 12,60 SPA 762 780 12,69 SPA 782 800 13,01 SPA 800 818 13,31 SPA 807 825 13,42 SPA 832 850 13,83 SPA 850 868 14,13 SPA 857 875 14,25 SPA 875 893 14,55 SPA 882 900 14,66 SPA 900 918 14,95 SPA 907 925 15,04 SPA 925 943 15,34 SPA 932 950 15,45 SPA 950 968 15,75 SPA 957 975 15,87 SPA 982 1000 16,28 SPA 1000 1018 16,57 SPA 1007 1025 16,69 SPA 1032 1050 17,10 SPA 1060 1078 17,54 SPA 1082 1100 17,88 SPA 1090 1108 18,10 SPA 1107 1125 18,31 SPA 1120 1138 18,51 SPA 1132 1150 18,72 SEZIONE SPA - SECTION SPA Est. (mm) Le (mm) List / SPA 1157 1175 19,13 SPA 1180 1198 19,50 SPA 1207 1225 19,95 SPA 1220 1238 20,14 SPA 1232 1250 20,33 SPA 1250 1268 20,62 SPA 1257 1275 20,74 SPA 1262 1280 20,82 SPA 1272 1290 21,01 SPA 1282 1300 21,15 SPA 1307 1325 21,56 SPA 1320 1338 21,77 SPA 1332 1350 21,98 SPA 1357 1375 22,39 SPA 1382 1400 22,80 SPA 1400 1418 23,06 SPA 1407 1425 23,18 SPA 1425 1443 23,47 SPA 1432 1450 23,59 SPA 1457 1475 24,00 SPA 1482 1500 24,41 SPA 1500 1518 24,71 SPA 1507 1525 24,82 SPA 1532 1550 25,23 SPA 1557 1575 25,62 SPA 1567 1585 25,78 SPA 1582 1600 26,03 SPA 1600 1618 26,32 SPA 1607 1625 26,44 SPA 1632 1650 26,85 SPA 1650 1668 27,14 SPA 1657 1675 27,26 SPA 1682 1700 27,67 SPA 1700 1718 27,96 SPA 1707 1725 28,08 SPA 1732 1750 28,47 SPA 1757 1775 28,88 SPA 1782 1800 29,29 SPA 1800 1818 29,58 SEZIONE SPA - SECTION SPA Est. (mm) Le (mm) List / SPA 1807 1825 29,70 SPA 1832 1850 30,11 SPA 1857 1875 30,52 SPA 1882 1900 30,90 SPA 1900 1918 31,20 SPA 1907 1925 31,32 SPA 1925 1943 31,61 SPA 1932 1950 31,73 SPA 1957 1975 32,14 SPA 1982 2000 32,55 SPA 2000 2018 32,84 SPA 2032 2050 33,37 SPA 2057 2075 33,75 SPA 2067 2085 33,93 SPA 2082 2100 34,16 SPA 2120 2138 34,78 SPA 2132 2150 34,99 SPA 2182 2200 35,81 SPA 2207 2225 36,22 SPA 2232 2250 36,60 SPA 2240 2258 36,75 SPA 2282 2300 37,42 SPA 2300 2318 37,71 SPA 2307 2325 37,83 SPA 2332 2350 38,24 SPA 2360 2378 38,69 SPA 2382 2400 39,04 SPA 2432 2450 39,86 SPA 2482 2500 40,68 SPA 2500 2518 40,98 SPA 2532 2550 41,50 SPA 2580 2598 42,27 SPA 2582 2600 42,30 SPA 2607 2625 42,71 SPA 2632 2650 43,12 SPA 2650 2668 43,42 SPA 2682 2700 43,95 SPA 2720 2738 44,56 SPA 2725 2743 44,63

CINGHIE TRAPEZOIDALI STRETTE SP CONVENTIONAL WRAPPED NARROW SEZIONE SPA - SECTION SPA Est. (mm) Le (mm) List / SPA 2732 2750 44,74 SPA 2782 2800 45,57 SPA 2800 2818 45,86 SPA 2832 2850 46,39 SPA 2847 2865 46,62 SPA 2882 2900 47,17 SPA 2932 2950 48,00 SPA 2982 3000 48,83 SPA 3000 3018 49,12 SPA 3032 3050 49,65 SPA 3082 3100 50,44 SPA 3150 3168 51,56 SPA 3182 3200 52,09 SPA 3250 3268 53,17 SPA 3282 3300 53,70 SPA 3350 3368 54,82 SPA 3382 3400 55,32 SPA 3400 3418 55,61 SPA 3450 3468 56,43 SPA 3482 3500 56,96 SPA 3550 3568 58,05 SPA 3650 3668 59,69 SPA 3750 3768 61,31 SPA 4000 4018 65,39 SPA 4250 4268 69,44 SPA 4500 4518 73,53 SEZIONE SPB - SECTION SPB Est. (mm) Le (mm) List / SPB 1250 1272 30,89 SPB 1280 1302 31,61 SPB 1320 1342 32,58 SPB 1360 1382 33,56 SPB 1400 1422 34,53 SPB 1450 1472 35,75 SPB 1500 1522 36,95 SPB 1550 1572 38,18 SEZIONE SPB - SECTION SPB Est. (mm) Le (mm) List / SPB 1600 1622 39,39 SPB 1650 1672 40,61 SPB 1700 1722 41,80 SPB 1750 1772 43,03 SPB 1757 1779 43,19 SPB 1800 1822 44,25 SPB 1850 1872 45,47 SPB 1860 1882 45,68 SPB 1900 1922 46,66 SPB 1950 1972 47,88 SPB 2000 2022 49,10 SPB 2020 2042 49,57 SPB 2060 2082 50,54 SPB 2110 2132 51,76 SPB 2120 2142 52,01 SPB 2180 2202 53,46 SPB 2240 2262 54,93 SPB 2246 2268 55,07 SPB 2264 2286 55,51 SPB 2280 2302 55,90 SPB 2300 2322 56,38 SPB 2320 2342 56,87 SPB 2360 2382 57,84 SPB 2391 2413 58,59 SPB 2410 2432 59,07 SPB 2430 2452 59,54 SPB 2500 2522 61,23 SPB 2530 2552 61,95 SPB 2580 2602 63,17 SPB 2650 2672 64,86 SPB 2680 2702 65,61 SPB 2720 2742 66,58 SPB 2780 2802 68,03 SPB 2800 2822 68,53 SPB 2840 2862 69,50 SPB 2900 2922 70,95 SPB 2950 2972 72,17 SPB 3000 3022 73,39 SPB 3070 3092 75,08 SEZIONE SPB - SECTION SPB Est. (mm) Le (mm) List / SPB 3150 3172 77,03 SPB 3170 3192 77,49 SPB 3250 3272 79,43 SPB 3350 3372 81,89 SPB 3425 3447 83,69 SPB 3450 3472 84,29 SPB 3550 3572 86,73 SPB 3650 3672 89,15 SPB 3675 3697 89,76 SPB 3750 3772 91,59 SPB 3800 3822 92,79 SPB 3870 3892 94,51 SPB 4000 4022 97,64 SPB 4060 4082 99,11 SPB 4120 4142 100,56 SPB 4250 4272 103,72 SPB 4310 4332 105,19 SPB 4370 4392 106,64 SPB 4500 4522 109,80 SPB 4750 4772 115,88 SPB 4870 4892 118,80 SPB 5000 5022 121,93 SPB 5300 5322 129,23 SPB 5600 5622 136,50 SPB 6000 6022 146,22 SPB 6300 6322 153,52 SPB 6450 6472 157,15 SPB 6700 6722 163,21 SPB 7100 7122 172,92 SPB 7500 7522 182,64 SPB 8000 8022 194,79 SPB 8500 8522 206,92 SEZIONE SPC - SECTION SPC Est. (mm) Le (mm) List / SPC 2000 2030 79,52 SPC 2120 2150 84,24 15 CINGHIE TRAPEZOIDALI STRETTE SP - WRAPPED NARROW SECTION V-BELT POWER

CINGHIE TRAPEZOIDALI STRETTE SP CONVENTIONAL WRAPPED NARROW CINGHIE TRAPEZOIDALI STRETTE SP - WRAPPED NARROW SECTION V-BELT POWER 16 SEZIONE SPC - SECTION SPC Est. (mm) Le (mm) List / SPC 2240 2270 88,93 SPC 2360 2390 93,63 SPC 2500 2530 99,11 SPC 2600 2630 103,03 SPC 2650 2680 105,00 SPC 2800 2830 110,86 SPC 3000 3030 118,71 SPC 3150 3180 124,57 SPC 3350 3380 132,42 SPC 3550 3580 140,25 SPC 3750 3780 148,08 SPC 4000 4030 157,87 SPC 4250 4280 167,67 SPC 4500 4530 177,48 SPC 4750 4780 187,27 SPC 5000 5030 197,04 SPC 5300 5330 208,81 SPC 5600 5630 220,55 SPC 6000 6030 236,23 SPC 6300 6330 247,97 SPC 6700 6730 263,65 SPC 7100 7130 279,31 SPC 7500 7530 294,99 SPC 8000 8030 314,58 SPC 8500 8530 334,15 SPC 9000 9030 353,75 SPC 9500 9530 373,35 SPC 10000 10030 392,94 SPC 10600 10630 416,43 SPC 11200 11230 439,94 SPC 11600 11630 455,62 SPC 11800 11830 463,44 SPC 12000 12030 471,27 SPC 12400 12430 486,95 SPC 12500 12530 490,86 SPC 15000 15030 588,82 SEZIONE 3V - SECTION 3V Est. (mm) Le (mm) List / 3V 250 635 8,52 3V 265 675 9,05 3V 280 710 9,53 3V 300 760 10,18 3V 315 800 10,75 3V 335 850 11,40 3V 355 900 12,07 3V 375 955 12,82 3V 400 1015 13,63 3V 425 1080 14,49 3V 450 1145 15,38 3V 475 1205 16,18 3V 500 1270 17,04 3V 530 1345 18,05 3V 560 1420 19,07 3V 600 1525 20,46 3V 630 1600 21,48 3V 670 1700 22,82 3V 710 1805 24,24 3V 750 1905 25,56 3V 800 2030 27,23 3V 850 2160 28,98 3V 900 2285 30,67 3V 950 2415 32,42 3V 1000 2540 34,08 3V 1060 2690 36,12 3V 1120 2845 38,17 3V 1180 2995 40,19 3V 1250 3175 42,61 3V 1320 3355 45,03 3V 1400 3555 47,71 SEZIONE 5V - SECTION 5V Est. (mm) Le (mm) List / 5V 500 1270 30,83 5V 530 1345 32,67 5V 560 1420 34,47 5V 600 1525 37,02 5V 630 1600 38,86 5V 670 1700 41,28 5V 710 1805 44,85 5V 750 1905 47,35 5V 800 2030 50,45 5V 850 2160 53,69 5V 900 2285 56,78 5V 950 2415 60,02 5V 1000 2540 63,12 5V 1060 2690 66,83 5V 1120 2845 70,70 5V 1180 2995 74,42 5V 1250 3175 78,90 5V 1320 3355 83,37 5V 1400 3555 88,33 5V 1500 3810 94,67 5V 1600 4065 101,00 5V 1700 4320 107,34 5V 1750 4445 110,50 5V 1800 4570 113,56 5V 1900 4825 119,89 5V 2000 5080 126,23 5V 2120 5385 133,81 5V 2240 5690 141,39 5V 2360 5995 148,95 5V 2500 6350 157,79 5V 2650 6730 167,22 5V 2800 7110 176,68 5V 3000 7620 189,35 5V 3150 8000 198,77 5V 3350 8515 211,58 5V 3550 9015 223,99

CINGHIE TRAPEZOIDALI STRETTE SP CONVENTIONAL WRAPPED NARROW SEZIONE 8V - SECTION 8V Est. (mm) Le (mm) List / 8V 1000 2540 127,13 8V 1060 2690 134,64 8V 1120 2845 142,39 8V 1180 2995 149,91 8V 1250 3175 158,90 8V 1320 3355 167,92 8V 1400 3555 177,94 8V 1500 3810 190,71 8V 1600 4065 203,44 8V 1700 4320 216,21 SEZIONE 8V - SECTION 8V Est. (mm) Le (mm) List / 8V 1800 4570 228,72 8V 1900 4825 241,49 8V 2000 5080 254,25 8V 2120 5385 269,51 8V 2240 5690 284,77 8V 2360 5995 300,05 8V 2500 6350 317,83 8V 2650 6730 336,84 8V 2800 7110 355,85 8V 3000 7620 381,38 SEZIONE 8V - SECTION 8V Est. (mm) Le (mm) List / 8V 3150 8000 400,39 8V 3350 8509 425,89 8V 3550 9017 451,30 8V 3750 9525 476,73 8V 4000 10160 508,51 8V 4250 10795 540,28 8V 4500 11430 572,09 8V 4750 12065 603,86 8V 5000 12700 635,63 17 CINGHIE TRAPEZOIDALI STRETTE SP - WRAPPED NARROW SECTION V-BELT POWER

CINGHIE MULTIBAND - MULTIBAND V-BELT HA HB HC HD 3V SPA SPB 5V/15J SPC 8V Cinghia di riferimento / Reference Belts A B C D 3V SPA SPB SPB SPC 8V Interasse gole mm / Groove centre distance mm 15 19 25 37 10 15 19 17,5 25 29 CINGHIE MULTIBAND - MULTIBAND V-BELT 18 Elementi / elemento Elements Element / HA 64 da 2 a 8 46,54 HA 74 da 2 a 8 53,80 HA 98 da 2 a 8 71,25 HB 72 da 2 a 8 75,82 HB 78 da 2 a 8 82,17 HB 86 da 2 a 8 90,60 HB 94 da 2 a 8 99,02 HB 108 da 2 a 8 113,77 HB 120 da 2 a 8 126,39 HB 124 da 2 a 8 130,62 HB 132 da 2 a 8 139,05 HB 133 da 2 a 8 140,10 HB 134 da 2 a 8 141,15 HB 136 da 2 a 8 143,24 HB 138 da 2 a 8 145,37 HB 148 da 2 a 8 155,90 HB 152 da 2 a 8 160,11 HB 173 da 2 a 8 182,25 HB 186 da 2 a 8 195,93 HC 138 da 2 a 8 248,99 HC 144 da 2 a 8 259,82 HC 160 da 2 a 8 288,65 HC 482 da 2 a 8 869,64 HD 225 da 2 a 8 719,45 SPA 3150 da 2 a 8 119,36 SPA 3550 da 2 a 8 134,52 Elementi / elemento Elements Element / SPA 4000 da 2 a 8 151,57 SPB 2240 da 2 a 8 113,82 SPB 2500 da 2 a 8 127,03 SPB 2580 da 2 a 8 131,12 SPB 2800 da 2 a 8 142,28 SPB 2900 da 2 a 8 147,98 SPB 3000 da 2 a 8 152,45 SPB 3150 da 2 a 8 160,08 SPB 3350 da 2 a 8 170,25 SPB 3550 da 2 a 8 180,37 SPB 3750 da 2 a 8 190,54 SPB 4250 da 2 a 8 215,97 SPB 4370 da 2 a 8 222,05 SPB 4500 da 2 a 8 228,68 SPB 4750 da 2 a 8 241,39 SPB 5000 da 2 a 8 254,06 SPB 5300 da 2 a 8 269,31 SPB 5600 da 2 a 8 284,57 SPB 6000 da 2 a 8 304,91 SPB 6300 da 2 a 8 320,16 SPB 7100 da 2 a 8 360,79 SPC 4000 da 2 a 8 375,69 SPC 4250 da 2 a 8 399,17 SPC 4750 da 2 a 8 446,12 SPC 5000 da 2 a 8 469,60 SPC 5600 da 2 a 8 525,95 Altre dimensioni disponibili NON a stock. Chiedere tempi di consega Other sizes available out stock. Ask for delivery time Elementi Elements / elemento Element / SPC 6000 da 2 a 8 563,55 SPC 6300 da 2 a 8 591,71 SPC 6700 da 2 a 8 629,28 SPC 7100 da 2 a 8 666,86 SPC 7500 da 2 a 8 704,42 SPC 8000 da 2 a 8 751,37 SPC 8500 da 2 a 8 798,33 SPC 9000 da 2 a 8 845,29 SPC 10000 da 2 a 8 939,24 3V 850 da 2 a 8 62,48 3V 1000 da 2 a 8 73,50 3V 1060 da 2 a 8 77,91 5V 630 da 2 a 8 80,45 5V 850 da 2 a 8 108,51 5V 1400 da 2 a 8 178,74 5V 1800 da 2 a 8 229,80 5V 2500 da 2 a 8 319,16 8V 1250 da 2 a 8 288,65 8V 2360 da 2 a 8 544,97 8V 2800 da 2 a 8 646,54 8V 3000 da 2 a 8 692,71 8V 3150 da 2 a 8 727,35 8V 3350 da 2 a 8 773,53 8V 3750 da 2 a 8 865,91

CINGHIE ESAGONALI PI BELT EXAGONAL BELTS 19 CINGHIE ESAGONALI PI BELT - EXAGONAL BELTS

CINGHIE ESAGONALI PI BELT PI BELT DOUBLE V List / List / List / CINGHIE ESAGONALI PI BELT - PI BELT DOUBLE V 20 AA 63** 56,62 AA 64** 57,51 AA 65** 58,41 AA 66** 59,31 AA 67 60,20 AA 68 61,11 AA 69** 62,01 AA 70 62,90 AA 71 63,80 AA 72 64,70 AA 73 65,60 AA 74** 66,50 AA 75 67,40 AA 76 68,30 AA 77 69,19 AA 78 70,09 AA 79 70,99 AA 80 71,89 AA 81 72,79 AA 82 73,69 AA 83 74,58 AA 84 75,48 AA 85 76,38 AA 86 77,29 AA 87 78,18 AA 88 79,08 AA 89 79,98 AA 90 80,87 AA 91 81,77 AA 92 82,68 AA 93 83,57 AA 94 84,47 AA 95 85,37 AA 96 86,26 AA 97 87,16 AA 98 88,07 AA 99 88,97 AA 100 89,86 AA 102 91,66 AA 103 92,55 AA 104 93,46 AA 105 94,36 AA 107 96,15 AA 108 97,05 AA 110 98,85 AA 112 100,65 AA 113 101,54 AA 115 103,35 AA 116 104,24 AA 118 106,04 AA 120 107,83 AA 124 111,43 AA 126 113,22 AA 127 114,13 AA 128 115,03 AA 130** 116,82 AA 131 117,72 AA 132** 118,61 AA 134** 120,42 AA 136** 122,21 AA 138** 124,00 AA 140** 125,81 AA 142** 127,60 AA 144** 129,40 AA 146** 131,20 AA 148** 132,99 AA 150** 134,79 AA 152 136,59 AA 155** 139,28 AA 158** 141,98 AA 162** 145,57 AA 167** 150,07 AA 173** 155,46 AA 177** 159,05 AA 180** 161,76 AA 187** 168,04 BB 75 92,71 BB 76 93,94 BB 77 95,18 BB 78 96,42 BB 79 97,65 BB 80 98,89 BB 81 100,12 BB 82 101,37 BB 83 102,60 BB 84 103,83 BB 85 105,07 BB 86 106,30 BB 87 107,54 BB 88 108,78 BB 89 110,01 BB 90 111,24 BB 91 112,49 BB 92 113,72 BB 93 114,96 BB 94 116,19 BB 95 117,43 BB 96 118,67 BB 97 119,90 BB 98 121,13 BB 99 122,38 BB 100 123,61 BB 101 124,85 BB 102 126,08 BB 103 127,31 BB 104 128,56 BB 105 129,79 BB 106 131,02 BB 107 132,26 BB 108 133,50 BB 110 135,97 BB 112 138,45 BB 113 139,68 BB 114 140,91 BB 115 142,15

CINGHIE ESAGONALI PI BELT PI BELT DOUBLE V List / List / List / BB 116 143,39 BB 118 145,86 BB 120 148,34 BB 122 150,80 BB 124 153,27 BB 126 155,75 BB 127 156,98 BB 128 158,22 BB 130 160,69 BB 131 161,93 BB 132 163,16 BB 133 164,40 BB 134 165,64 BB 135 166,87 BB 136 168,11 BB 138 170,58 BB 140 173,05 BB 142 175,53 BB 144 178,00 BB 146 180,47 BB 147** 181,71 BB 148** 182,94 BB 151** 186,65 BB 152** 187,89 BB 154 190,36 BB 155 191,60 BB 157** 194,06 BB 158 195,31 BB 161 199,01 BB 162** 200,24 BB 163** 201,49 BB 165** 203,95 BB 167** 206,43 BB 168** 207,66 BB 169** 208,90 BB 173 213,84 BB 175** 216,32 BB 177** 218,79 BB 180 222,50 BB 186** 229,91 BB 187** 231,15 BB 188** 232,39 BB 192** 237,33 BB 195 241,04 BB 197** 243,51 BB 200** 247,21 BB 201** 248,46 BB 204** 252,16 BB 208** 257,10 BB 210 259,58 BB 212** 262,05 BB 214** 264,53 BB 217** 268,24 BB 220** 271,94 BB 221** 273,17 BB 223** 275,65 BB 224** 276,88 BB 225** 278,12 BB 228** 281,83 BB 229** 283,06 BB 232** 286,77 BB 237** 292,95 BB 240 296,66 BB 248 306,55 BB 249** 307,79 BB 253** 312,73 BB 255** 315,21 BB 259** 320,14 BB 265** 327,57 BB 270 333,74 BB 276** 341,17 BB 280** 346,10 BB 285** 352,29 BB 300 370,83 BB 315** 389,37 BB 330** 407,91 BB 345** 426,45 BB 360** 444,99 BB 361** 446,23 BB 366** 452,41 BB 374** 462,30 BB 394** 487,03 ** Misure disponibili NON a stock. Chiedere tempi di consega ** Not available in stock. Ask for delivery time List / CC 91** 179,69 CC 92** 181,65 CC 93** 183,63 CC 94** 185,60 CC 95** 187,58 CC 96 189,55 CC 97** 191,53 CC 98** 193,50 CC 99** 195,48 CC 100** 197,45 CC 101** 199,43 CC 102** 201,40 CC 104** 205,35 CC 105 207,33 CC 106 209,30 CC 108** 213,25 CC 110** 217,20 CC 111** 219,18 CC 112 221,14 CC 114** 225,09 CC 115** 227,07 CC 116** 229,04 CC 117** 231,02 CC 118** 232,99 CC 120 236,94 CC 122** 240,89 CC 124** 244,84 CC 126 248,80 CC 128 252,75 21 CINGHIE ESAGONALI PI BELT - PI BELT DOUBLE V

CINGHIE ESAGONALI PI BELT PI BELT DOUBLE V List / List / CINGHIE ESAGONALI PI BELT - PI BELT DOUBLE V 22 CC 130** 256,70 CC 132** 260,65 CC 134** 264,59 CC 136** 268,54 CC 138** 272,49 CC 140 276,44 CC 142** 280,39 CC 144 284,34 CC 145** 286,31 CC 146** 288,29 CC 147** 290,26 CC 148** 292,24 CC 150** 296,19 CC 152** 300,14 CC 153 302,10 CC 154** 304,08 CC 158** 311,98 CC 160** 315,93 CC 162 319,88 CC 165 325,80 CC 166** 327,78 CC 168** 331,73 CC 170 335,68 CC 173 341,59 CC 175** 345,54 CC 177** 349,49 CC 178** 351,47 CC 180 355,42 CC 185** 365,29 CC 187** 369,24 CC 189** 373,19 CC 193 381,08 CC 195 385,03 CC 197** 388,98 CC 200** 394,91 CC 204** 402,81 CC 208** 410,71 CC 210 414,66 CC 212** 418,61 CC 215** 424,52 CC 216** 426,50 CC 218** 430,45 CC 220** 434,40 CC 222** 438,35 CC 223** 440,32 CC 224** 442,30 CC 225** 444,27 CC 228** 450,20 CC 230** 454,15 CC 236** 465,99 CC 238** 469,94 CC 240 473,89 CC 248** 489,69 CC 250** 493,64 CC 255** 503,51 CC 260** 513,38 CC 261** 515,36 CC 265** 523,26 CC 268** 529,18 CC 270 533,13 CC 276** 544,97 CC 280** 552,87 CC 285** 562,75 CC 297** 586,44 CC 300** 592,36 CC 303** 598,29 CC 314** 620,00 CC 315** 621,98 CC 316** 623,95 CC 330** 651,60 CC 336** 663,44 CC 345** 681,22 CC 348** 687,14 CC 350** 691,09 CC 352** 695,04 CC 354** 698,98 CC 360 710,83 ** Misure disponibili NON a stock. Chiedere tempi di consega ** Not available in stock. Ask for delivery time

CINGHIE TRAPEZOIDALI DENTELLATE X POWER 23 SPZX SPAX SPBX SPCX CINGHIE TRAPEZOIDALI DENTELLATE X POWER

RAW EDGE V-BELT X POWER SPZX SPAX SPBX SPCX 24 RAW EDGE V-BELT X POWER

CINGHIE TRAPEZOIDALI DENTELLATE RAW EDGE V-BELT X POWER SEZIONE AX - SECTION AX Int. (mm) Li (mm) List / AX 20 508 13,77 AX 22 559 15,14 AX 25 635 17,20 AX 29 737 19,94 AX 30 762 20,62 AX 31 787 21,31 AX 32 810 21,92 AX 33 838 22,69 AX 34 863 23,37 AX 35 890 24,08 AX 36 914 24,74 AX 37 940 25,44 AX 38 965 26,14 AX 39 990 26,82 AX 40 1016 27,50 AX 41 1041 28,18 AX 42 1067 28,89 AX 43 1092 29,57 AX 44 1120 30,34 AX 45 1143 30,93 AX 46 1168 31,61 AX 47 1194 32,32 AX 48 1220 33,04 AX 49 1250 33,83 AX 50 1270 34,40 AX 51 1295 35,05 AX 52 1320 35,74 AX 53 1346 36,44 AX 54 1372 37,15 AX 55 1400 37,89 AX 56 1425 38,58 AX 57 1450 39,26 AX 58 1475 39,94 AX 59 1500 40,62 AX 60 1525 41,30 AX 61 1550 41,96 AX 62 1575 42,64 AX 63 1600 43,32 AX 64 1625 44,00 SEZIONE AX - SECTION AX Int. (mm) Li (mm) List / AX 65 1650 44,68 AX 66 1675 45,36 AX 67 1700 46,02 AX 68 1725 46,70 AX 69 1750 47,38 AX 70 1775 48,06 AX 71 1800 48,74 AX 72 1826 49,42 AX 73 1854 50,19 AX 74 1880 50,90 AX 75 1905 51,58 AX 76 1930 52,26 AX 77 1956 52,94 AX 78 1981 53,62 AX 79 2005 54,28 AX 80 2031 54,99 AX 81 2085 56,44 AX 82 2083 56,39 AX 83 2100 56,86 AX 84 2133 57,75 AX 85 2160 58,48 AX 86 2185 59,16 AX 87 2210 59,82 AX 88 2235 60,50 AX 89 2260 61,18 AX 90 2286 61,89 AX 91 2311 62,58 AX 92 2337 63,29 AX 93 2362 63,94 AX 94 2383 64,51 AX 95 2413 65,33 AX 96 2438 66,01 AX 97 2464 66,72 SEZIONE BX - SECTION BX Int. (mm) Li (mm) List / BX 28 710 29,57 BX 32 813 33,88 BX 34 863 35,95 BX 35 890 37,09 BX 36 914 38,08 BX 38 965 40,20 BX 39 990 41,23 BX 40 1016 42,33 BX 41 1041 43,36 BX 42 1067 44,45 BX 43 1092 45,49 BX 44 1120 46,66 BX 45 1143 47,62 BX 46 1168 48,68 BX 47 1194 49,74 BX 48 1220 50,82 BX 49 1250 52,08 BX 50 1270 52,93 BX 51 1295 53,97 BX 52 1320 55,00 BX 53 1346 56,10 BX 54 1372 57,15 BX 55 1400 58,32 BX 56 1425 59,38 BX 57 1450 60,42 BX 58 1475 61,45 BX 59 1500 62,49 BX 60 1525 63,53 BX 61 1550 64,59 BX 62 1575 65,63 BX 63 1600 66,67 BX 64 1625 67,71 BX 65 1650 68,74 BX 66 1675 69,80 BX 67 1700 70,84 BX 68 1725 71,87 BX 69 1750 72,91 BX 70 1775 73,95 BX 71 1800 74,98 25 CINGHIE TRAPEZOIDALI DENTELLATE - RAW EDGE V-BELT X POWER

CINGHIE TRAPEZOIDALI DENTELLATE RAW EDGE V-BELT X POWER CINGHIE TRAPEZOIDALI DENTELLATE - RAW EDGE V-BELT X POWER 26 SEZIONE BX - SECTION BX Int. (mm) Li (mm) List / BX 72 1825 76,05 BX 73 1854 77,24 BX 74 1880 78,33 BX 75 1905 79,37 BX 76 1930 80,41 BX 77 1956 81,50 BX 78 1981 82,53 BX 79 2005 83,54 BX 80 2031 84,63 BX 81 2058 85,74 BX 82 2083 86,78 BX 83 2100 87,50 BX 84 2133 88,88 BX 85 2160 90,00 BX 86 2185 91,03 BX 87 2210 92,09 BX 88 2235 93,13 BX 89 2260 94,17 BX 90 2286 95,26 BX 91 2311 96,29 BX 92 2337 97,38 BX 93 2362 98,42 BX 94 2388 99,51 BX 95 2413 100,55 BX 96 2438 101,58 BX 97 2465 102,70 BX 98 2500 104,18 BX 100 2540 105,83 BX 105 2667 144,53 BX 110 2795 151,45 BX 116 2945 159,59 BX 120 3048 165,16 SEZIONE CX - SECTION CX Int. (mm) Li (mm) List / CX 51 1295 79,75 CX 53 1350 83,14 CX 55 1400 86,21 CX 60 1524 93,85 CX 68 1727 106,34 CX 72 1829 112,62 CX 75 1905 117,31 CX 78 1981 121,98 CX 81 2057 126,66 CX 85 2159 132,95 CX 87 2211 136,14 CX 90 2286 140,77 CX 93 2362 145,45 CX 96 2438 150,12 CX 100 2540 156,41 CX 110 2800 198,27 CX 114 2896 205,07 SEZIONE SPZX - SECTION SPZX Norme Americane USA List / SPZX 587 13,04 SPZX 607 13,48 SPZX 612 13,61 SPZX 630 3VX 250 14,00 SPZX 637 14,15 SPZX 662 3VX 260 14,72 SPZX 670 3VX 265 14,90 SPZX 687 15,27 SPZX 710 3VX 280 15,79 SPZX 722 16,05 SPZX 737 16,38 SPZX 750 16,66 SPZX 762 3VX 300 16,92 SPZX 775 17,10 SPZX 787 17,11 SPZX 800 3VX 315 17,12 SPZX 812 17,37 SEZIONE SPZX - SECTION SPZX Norme Americane USA List / SPZX 837 17,92 SPZX 850 3VX 335 18,19 SPZX 862 18,44 SPZX 875 18,72 SPZX 887 3VX 350 18,99 SPZX 900 3VX 355 19,26 SPZX 912 19,50 SPZX 925 19,79 SPZX 937 20,03 SPZX 950 3VX 375 20,34 SPZX 960 20,53 SPZX 962 20,58 SPZX 975 20,85 SPZX 987 21,10 SPZX 1000 21,38 SPZX 1012 3VX 400 21,65 SPZX 1024 21,90 SPZX 1037 22,18 SPZX 1047 3VX412 22,40 SPZX 1060 22,68 SPZX 1062 22,72 SPZX 1077 3VX 425 23,05 SPZX 1087 23,25 SPZX 1112 23,80 SPZX 1120 23,95 SPZX 1137 3VX 450 24,32 SPZX 1140 24,40 SPZX 1147 24,55 SPZX 1162 24,85 SPZX 1180 25,25 SPZX 1187 25,40 SPZX 1202 3VX 475 25,73 SPZX 1212 25,92 SPZX 1237 26,47 SPZX 1250 26,74 SPZX 1262 3VX 500 26,99 SPZX 1270 27,17 SPZX 1287 27,54 SPZX 1312 28,07

CINGHIE TRAPEZOIDALI DENTELLATE RAW EDGE V-BELT X POWER SEZIONE SPZX - SECTION SPZX Norme Americane USA List / SPZX 1320 3VX 520 28,24 SPZX 1337 3VX 530 28,59 SPZX 1340 28,66 SPZX 1362 29,14 SPZX 1387 29,67 SPZX 1400 29,94 SPZX 1412 3VX 560 30,21 SPZX 1420 30,39 SPZX 1437 30,74 SPZX 1462 31,29 SPZX 1487 31,81 SPZX 1500 32,09 SPZX 1512 3VX 600 32,36 SPZX 1520 32,53 SPZX 1537 32,89 SPZX 1562 3VX 617 33,40 SPZX 1587 33,96 SPZX 1600 3VX 630 34,23 SPZX 1612 34,47 SPZX 1637 35,02 SPZX 1662 35,55 SPZX 1687 36,10 SPZX 1700 3VX 670 36,37 SPZX 1737 37,15 SPZX 1762 37,69 SPZX 1787 38,22 SPZX 1800 3VX 710 38,49 SPZX 1812 38,77 SPZX 1850 39,57 SPZX 1862 39,84 SPZX 1887 40,37 SPZX 1900 3VX 750 40,64 SPZX 1937 41,44 SPZX 1962 41,96 SPZX 1987 42,51 SPZX 2000 42,79 SPZX 2019 43,19 SPZX 2037 3VX 800 43,59 SPZX 2120 45,36 SEZIONE SPZX - SECTION SPZX Norme Americane USA List / SPZX 2187 46,77 SPZX 2240 47,93 SPZX 2280 3VX 900 48,77 SPZX 2360 50,49 SPZX 2500 53,49 SEZIONE SPAX - SECTION SPAX Est. (mm) Le (mm) List / SPAX 612 630 17,34 SPAX 710 728 20,11 SPAX 732 750 20,74 SPAX 757 775 21,44 SPAX 782 800 22,16 SPAX 800 818 22,66 SPAX 807 825 22,86 SPAX 812 830 22,99 SPAX 832 850 23,57 SPAX 850 868 24,08 SPAX 857 875 24,29 SPAX 875 893 24,78 SPAX 882 900 24,99 SPAX 900 918 25,51 SPAX 907 925 25,68 SPAX 925 943 26,20 SPAX 932 950 26,42 SPAX 950 968 26,90 SPAX 957 975 27,11 SPAX 982 1000 27,81 SPAX 1000 1018 28,33 SPAX 1007 1025 28,53 SPAX 1012 1030 28,66 SPAX 1032 1050 29,24 SPAX 1048 1066 29,68 SPAX 1060 1078 30,01 SPAX 1082 1100 30,66 SPAX 1107 1125 31,36 SPAX 1120 1138 31,73 SEZIONE SPAX - SECTION SPAX Est. (mm) Le (mm) List / SPAX 1132 1150 32,07 SPAX 1150 1168 32,58 SPAX 1157 1175 32,79 SPAX 1180 1198 33,44 SPAX 1207 1225 34,19 SPAX 1232 1250 34,88 SPAX 1250 1268 35,40 SPAX 1257 1275 35,62 SPAX 1282 1300 36,31 SPAX 1307 1325 37,01 SPAX 1320 1338 37,40 SPAX 1332 1350 37,74 SPAX 1357 1375 38,44 SPAX 1382 1400 39,14 SPAX 1400 1418 39,66 SPAX 1407 1425 39,86 SPAX 1432 1450 40,56 SPAX 1450 1468 41,08 SPAX 1457 1475 41,27 SPAX 1482 1500 41,99 SPAX 1500 1518 42,49 SPAX 1507 1525 42,69 SPAX 1532 1550 43,39 SPAX 1550 1568 43,91 SPAX 1557 1575 44,12 SPAX 1582 1600 44,82 SPAX 1600 1618 45,34 SPAX 1607 1625 45,51 SPAX 1632 1650 46,25 SPAX 1682 1700 47,64 SPAX 1700 1718 48,16 SPAX 1707 1725 48,36 SPAX 1732 1750 49,06 SPAX 1757 1775 49,77 SPAX 1782 1800 50,49 SPAX 1800 1818 50,99 SPAX 1807 1825 51,19 SPAX 1832 1850 51,89 SPAX 1857 1875 52,62 27 CINGHIE TRAPEZOIDALI DENTELLATE - RAW EDGE V-BELT X POWER

CINGHIE TRAPEZOIDALI DENTELLATE RAW EDGE V-BELT X POWER CINGHIE TRAPEZOIDALI DENTELLATE - RAW EDGE V-BELT X POWER 28 SEZIONE SPAX - SECTION SPAX Est. (mm) Le (mm) List / SPAX 1882 1900 53,32 SPAX 1900 1918 53,84 SPAX 1907 1925 54,02 SPAX 1932 1950 54,75 SPAX 1957 1975 55,45 SPAX 1982 2000 56,14 SPAX 2000 2018 56,66 SPAX 2032 2050 57,56 SPAX 2057 2075 58,27 SPAX 2082 2100 58,97 SPAX 2120 2138 60,06 SPAX 2240 2258 63,45 SPAX 2282 2300 64,65 SPAX 2293 2311 64,95 SPAX 2300 2318 65,17 SPAX 2307 2325 65,34 SPAX 2360 2378 66,85 SPAX 2432 2450 68,89 SPAX 2482 2500 70,32 SPAX 2500 2518 70,82 SPAX 2580 2598 86,46 SPAX 2582 2600 86,53 SPAX 2650 2668 88,81 SPAX 2682 2700 89,90 SPAX 2720 2738 91,15 SPAX 2800 2818 93,84 SPAX 3000 3018 100,54 SPAX 3150 3168 105,57 SPAX 3350 3368 112,28 SPAX 3550 3568 118,97 SPAX 3750 3768 125,68 SPAX 4000 4018 134,07 SPAX 4250 4268 142,44 SPAX 4500 4518 150,81 SEZIONE SPBX - SECTION SPBX Norme Americane USA List / SPBX 1250 56,20 NEW SPBX 1260 5VX 500 56,66 SPBX 1270 57,11 SPBX 1320 59,36 SPBX 1340 60,24 SPBX 1350 5VX 530 60,70 SPBX 1360 61,15 SPBX 1400 5VX 560 62,94 SPBX 1450 65,19 SPBX 1470 66,10 SPBX 1500 5VX 600 67,44 SPBX 1514 68,06 SPBX 1550 69,68 SPBX 1600 5VX 630 71,93 SPBX 1650 5VX650 74,17 SPBX 1690 75,99 SPBX 1700 5VX 670 76,44 SPBX 1750 78,69 SPBX 1800 5VX 710 80,94 SPBX 1900 5VX 750 85,43 SPBX 2000 5VX 800 89,92 SPBX 2060 5VX 820 92,62 SPBX 2120 5VX 840 95,32 SPBX 2240 100,72 SPBX 2280 5VX 900 102,51 SPBX 2360 106,10 SPBX 2400 5VX 950 107,91 SPBX 2500 112,41 SPBX 2530 5VX1000 113,75 SPBX 2580 132,97 SPBX 2650 136,58 SPBX 2680 5VX 1060 138,13 SPBX 2710 139,69 SPBX 2730 140,70 SPBX 2800 144,31 SPBX 2840 5VX 1120 146,38 SPBX 2900 149,47 SPBX 3000 5VX 1180 154,63 SPBX 3150 5VX 1250 162,37 SEZIONE SPBX - SECTION SPBX Norme Americane USA List / SPBX 3350 5VX 1320 172,67 SPBX 3550 5VX 1400 182,97 SPBX 3750 193,28 SPBX 3800 195,87 SPBX 3825 5VX 1500 197,14 SPBX 4000 206,17 SPBX 4050 5VX 1600 208,74 SPBX 4250 219,05 SPBX 4300 5VX 1700 221,64 SPBX 4500 231,95 SPBX 4550 5VX 1900 234,51 SPBX 5000 255,55 SEZIONE SPCX - SECTION SPCX Est. (mm) Le (mm) List / SPCX 2000 2030 177,63 SPCX 2120 2150 188,29 SPCX 2240 2270 198,94 SPCX 2360 2390 209,60 SPCX 2500 2530 222,04 SPCX 2650 2680 270,67 SPCX 2800 2830 285,99 SPCX 3000 3030 306,42 SPCX 3150 3180 321,74 SPCX 3350 3380 342,17 SPCX 3550 3580 362,59 SPCX 3750 3780 383,01 SPCX 4000 4030 408,54 SPCX 4250 4280 434,08 SPCX 4500 4530 459,62 SPCX 5000 5030 510,69

CINGHIE PIANE PI FLAT - PI FLAT - FLAT BELTS 29 CINGHIE PIANE PI FLAT - PI FLAT - FLAT BELTS

CINGHIE PIANE PI FLAT PI FLAT - FLAT BELTS CINGHIE PIANE PI FLAT - PI FLAT - FLAT BELTS 30 CINGHIE PIANE - FLAT BELTS Lp mm. Larghezza Manicotto Width sleeve / mm. 263 450 1,32 269 450 1,35 283 450 1,43 292 450 1,47 299 450 1,50 313 450 1,58 328 450 1,65 340 450 1,71 349 450 1,75 359 450 1,81 370 450 1,87 391 450 1,97 406 450 2,05 410 450 2,07 418 450 2,11 430 450 2,16 444 450 2,24 451 450 2,27 457 450 2,30 475 450 2,39 482 450 2,43 489 450 2,47 500 450 2,52 517 450 2,60 533 450 2,69 545 450 2,75 558 450 2,81 573 450 2,89 590 450 2,97 597 450 3,00 610 450 3,08 622 450 3,13 630 450 3,17 660 450 3,33 674 450 3,39 693 450 3,50 711 450 3,58 720 450 3,62 740 450 3,73 CINGHIE PIANE - FLAT BELTS Lp mm. Larghezza Manicotto Width sleeve / mm. 756 450 3,81 766 450 3,86 773 450 3,90 798 450 4,02 813 450 4,10 821 450 4,14 830 450 4,18 845 450 4,25 857 450 4,32 870 450 4,38 887 450 4,47 905 450 4,56 919 450 4,63 930 450 4,68 945 450 4,76 956 450 4,82 965 450 4,86 980 450 4,94 990 450 4,99 998 450 5,03 1008 450 5,08 1015 450 5,11 1028 450 5,18 1043 450 5,25 1054 450 5,31 1067 450 5,38 1091 450 5,49 1105 450 5,57 1117 450 5,63 1142 450 5,75 1156 450 5,83 1182 450 5,95 1202 450 6,06 1222 450 6,15 1232 450 6,21 1260 450 6,35 1270 450 6,39 1321 450 6,66 1350 450 6,80 CINGHIE PIANE - FLAT BELTS Lp mm. Larghezza Manicotto Width sleeve / mm. 1380 450 6,95 1399 450 7,05 1422 450 7,16 1472 450 7,41 1492 450 7,52 1560 450 7,85 1585 450 7,98 1600 450 8,06 1626 450 8,19 1651 450 8,32 1690 450 8,52 1740 450 8,77 1765 450 8,89 1804 450 9,08 1859 450 9,37 1901 450 9,58 1936 450 9,75 1975 450 9,95 2045 450 10,30 2075 450 10,45 2121 450 10,69 2159 450 10,88 2197 450 11,07 2240 450 11,29 2261 450 11,39 2298 450 11,57 2324 450 11,71 2345 450 11,81 2400 450 12,09 2426 450 12,22 2456 450 12,37 2507 450 12,63 2541 450 12,80 2604 450 13,11

CINGHIE A NERVATURE POLY POWER POLY POWER RIBBED BELTS 31 CINGHIE A NERVATURE POLY POWER - POLY POWER RIBBED BELTS

CINGHIE A NERVATURE POLY POWER POLY POWER RIBBED BELTS PROFILO J - PROFILE J PROFILO J - PROFILE J PROFILO J - PROFILE J CINGHIE A NERVATURE POLY POWER - POLY POWER RIBBED BELTS 32 / Lp Lp pollici Lp Inch / Nervatura / Rib 356 J 14,00 7,02 381 J 15,00 7,02 406 J 16,00 7,02 432 J 17,00 7,67 457 J 18,00 3,83 483 J 19,00 4,79 508 J 20,00 4,79 533 J 21,00 4,79 559 J 22,00 4,79 584 J 23,00 4,79 610 J 24,00 4,79 635 J 25,00 4,79 660 J 26,00 5,43 686 J 27,00 5,43 711 J 28,00 5,43 723 J** 28,50 5,43 737 J 29,00 5,43 762 J 30,00 5,43 790 J 31,00 5,43 813 J 32,00 6,07 838 J 33,00 6,07 864 J 34,00 6,07 889 J 35,00 6,07 / Lp Lp pollici Lp Inch / Nervatura / Rib 914 J 36,00 6,07 940 J 37,00 6,07 950 J 37,40 6,07 965 J 38,00 6,07 991 J 39,00 6,07 1016 J 40,00 7,02 1041 J 41,00 7,02 1054 J 41,50 7,02 1067 J 42,00 7,02 1092 J 43,00 7,02 1110 J** 43,70 7,02 1118 J 44,00 7,02 1126 J 44,30 7,02 1143 J 45,00 7,02 1150 J 45,30 7,02 1168 J 46,00 7,34 1194 J 47,00 7,67 1219 J 48,00 7,67 1233 J** 48,50 7,67 1245 J 49,00 7,67 1270 J 50,00 7,67 1280 J** 50,40 7,67 1295 J 51,00 7,67 ** Misure disponibili NON a stock. Chiedere tempi di consega ** Not available in stock. Ask for delivery time / Lp Lp pollici Lp Inch / Nervatura / Rib 1301 J** 51,20 7,67 1315 J 51,80 7,67 1321 J 52,00 7,67 1333 J** 52,50 7,67 1346 J 53,00 7,67 1355 J** 53,30 7,67 1372 J 54,00 7,67 1397 J 55,00 8,62 1428J 56,20 8,62 1473 J 58,00 8,62 1549 J 61,00 9,26 1600 J** 63,00 9,26 1651 J 65,00 9,26 1663 J** 65,50 9,26 1752 J 69,00 9,89 1854 J 73,00 9,89 1895 J** 74,50 9,89 1910 J** 75,20 9,89 1956 J** 77,00 10,86 1992 J** 78,50 10,86 2083 J** 82,00 11,81 2210 J 87,00 11,81 2337 J* 92,00 12,45 2413 J** 95,00 23,94 2489 J 98,00 29,04

CINGHIE A NERVATURE POLY POWER POLY POWER RIBBED BELTS PROFILO L - PROFILE L PROFILO L - PROFILE L PROFILO L - PROFILE L / Lp Lp pollici Lp Inch / Nervatura / Rib / Lp Lp pollici Lp Inch / Nervatura / Rib / Lp Lp pollici Lp Inch / Nervatura / Rib 954 L 37,50 21,98 991 L 39,00 21,98 1075 L 42,30 23,19 1270 L 50,00 25,64 1333 L 52,50 26,25 1371 L 54,00 26,86 1397 L 55,00 27,47 1422 L 56,00 28,08 1480 L** 58,30 28,48 1562 L 61,50 29,31 1613 L 63,50 29,91 1664 L 65,50 30,52 1715 L 67,50 31,13 1764 L 69,50 31,74 1803 L 71,00 32,35 1841 L 72,50 32,35 1943 L 76,50 33,58 1981 L 78,00 34,19 2020 L 79,50 34,80 2070 L 81,50 35,41 2096 L 82,50 37,85 2134 L 84,00 37,85 2197 L** 86,50 37,85 2235 L 88,00 37,85 2324 L 91,50 38,46 2362 L 93,00 39,07 2476 L 97,50 40,29 2515 L 99,00 40,90 2705 L 106,50 48,84 2743 L 108,00 49,44 2845 L 112,00 51,28 2895 L 114,00 51,89 2921 L 115,00 45,79 2997 L 118,00 53,72 3086 L 121,50 55,56 3124 L 123,00 56,16 3289 L 129,50 59,22 3327 L 131,00 59,83 3492 L 137,50 62,27 3696 L 145,50 65,93 4051 L 159,50 72,65 4191 L 165,00 75,09 4470 L 176,00 80,32 4622 L 182,00 82,41 5029 L 198,00 89,74 5385 L 212,00 96,45 33 ** Misure disponibili NON a stock. Chiedere tempi di consega ** Not available in stock. Ask for delivery time CINGHIE A NERVATURE POLY POWER - POLY POWER RIBBED BELTS

CINGHIE PER VARIATORI VARI POWER VARI POWER VARIABLE SPEED BELTS Specifiche per l utilizzo su pulegge variabili e pertanto trovano impiego essenzialmente nei variatori industriali di velocità (settore tessile, cartario, chimico, ecc.). Cinghie anticalore e antiolio. Made for fit on variable pulleys and therefore are used essentially in industrial speed drives (textile, paper, chemical, etc..). Heat and oil resistant belts. Sezione / Section WxT (mm) 17X6 22X8 28X8 37X10 47X13 Angolo / Angle 26 26 26 28 28 34 CINGHIE PER VARIATORI VARI POWER - VARI POWER VARIABLE SPEED BELTS

CINGHIE PER VARIATORI VARI POWER VARI POWER VARIABLE SPEED BELTS Sezione (mm) Section (mm) Int. (mm) Int. Lenght (mm) List / Sezione (mm) Section (mm) Int. (mm) Int. Lenght (mm) List / Sezione (mm) Section (mm) Int. (mm) Int. Lenght (mm) List / 17 X 6 550 97,75 17 X 6 600 97,75 17 X 6 650 103,92 17 X 6 700 103,92 17 X 6 750 109,75 17 X 6 800 109,75 17 X 6 850 115,28 17 X 6 900 115,28 17 X 6 1000 120,82 17 X 6 1050 125,35 17 X 6 1100 129,90 17 X 6 1150 136,40 17 X 6 1200 141,26 17 X 6 1300 152,63 22 X 8 485 121,78 22 X 8 500 121,78 22 X 8 525 129,90 22 X 8 550 129,90 22 X 8 561 129,90 22 X 8 575 129,90 22 X 8 600 129,90 22 X 8 625 139,63 22 X 8 650 139,63 22 X 8 700 139,63 22 X 8 750 147,76 22 X 8 775 147,76 22 X 8 800 147,76 22 X 8 850 157,49 22 X 8 900 157,49 22 X 8 950 165,62 22 X 8 1000 165,62 22 X 8 1060 173,73 22 X 8 1120 183,48 22 X 8 1180 183,48 22 X 8 1225 193,22 22 X 8 1250 193,22 22 X 8 1320 201,34 22 X 8 1400 201,34 22 X 8 1500 211,08 22 X 8 1600 220,82 22 X 8 1640 222,44 22 X 8 1800 238,68 22 X 8 1900 253,29 22 X 8 2000 269,53 22 X 8 2120 285,77 28 X 8 500 134,77 28 X 8 525 144,51 28 X 8 550 144,51 28 X 8 600 144,51 28 X 8 625 154,26 28 X 8 645 154,26 28 X 8 695 154,26 28 X 8 745 165,62 28 X 8 800 165,62 28 X 8 845 175,36 28 X 8 895 175,36 28 X 8 945 185,11 28 X 8 995 185,11 28 X 8 1005 185,11 28 X 8 1055 194,84 28 X 8 1115 204,58 28 X 8 1180 204,58 28 X 8 1250 215,96 28 X 8 1300 225,69 28 X 8 1320 225,69 28 X 8 1395 225,69 28 X 8 1500 235,44 28 X 8 1600 245,18 28 X 8 1700 256,54 28 X 8 1800 266,29 28 X 8 1900 285,77 28 X 8 2000 300,39 28 X 8 2500 371,83 35 CINGHIE PER VARIATORI VARI POWER - VARI POWER VARIABLE SPEED BELTS

CINGHIE PER VARIATORI VARI POWER VARI POWER VARIABLE SPEED BELTS CINGHIE PER VARIATORI VARI POWER - VARI POWER VARIABLE SPEED BELTS 36 Sezione (mm) Section (mm) Int. (mm) Int. Lenght (mm) List / 37 X 10 675 206,21 37 X 10 700 206,21 37 X 10 750 222,44 37 X 10 800 222,44 37 X 10 850 235,44 37 X 10 900 235,44 37 X 10 950 250,06 37 X 10 1000 250,06 37 X 10 1060 263,04 37 X 10 1120 279,28 37 X 10 1180 279,28 37 X 10 1250 295,52 37 X 10 1320 308,50 37 X 10 1400 308,50 37 X 10 1500 323,11 37 X 10 1600 337,73 37 X 10 1700 353,96 37 X 10 1800 366,95 37 X 10 2000 396,19 37 X 10 2240 464,37 37 X 10 2500 519,58 Sezione (mm) Section (mm) Int. (mm) Int. Lenght (mm) List / 47 X 12 600 219,21 47 X 12 750 274,40 47 X 12 850 311,75 47 X 12 875 311,75 47 X 12 900 311,75 47 X 12 950 331,24 47 X 12 1000 331,24 47 X 12 1030 347,48 47 X 12 1060 347,48 47 X 12 1120 368,58 47 X 12 1145 368,58 47 X 12 1180 368,58 47 X 12 1250 389,69 47 X 12 1270 389,69 47 X 12 1320 409,18 47 X 12 1400 409,18 47 X 12 1435 409,18 47 X 12 1500 427,04 47 X 12 1565 444,90 47 X 12 1600 444,90 47 X 12 1700 469,25 47 X 12 1740 483,86 47 X 12 1800 483,86 47 X 12 2060 542,32 47 X 12 2210 584,53 47 X 12 2240 584,53 47 X 12 2500 688,45 Sezione (mm) Section (mm) Int. (mm) Int. Lenght (mm) List / 55 X 16 960 412,98 55 X 16 1180 498,48 55 X 16 1250 525,86 55 X 16 1320 552,69 55 X 16 1400 583,98 55 X 16 1500 623,10 55 X 16 1600 661,94 55 X 16 1700 700,50 55 X 16 1800 739,62 55 X 16 1900 778,46 55 X 16 2000 817,58 55 X 16 2120 864,24 55 X 16 2240 910,90 55 X 16 2360 957,56 55 X 16 2800 1128,85 55 X 16 3150 1265,00 Le misure 13X6, 27X8, 70X19 sono disponibili a richiesta. Contattateci per prezzi e disponibilità. 13X6, 27X8, 70X19 are available on request. Contact us.

CINGHIE E MANICOTTI DENTATI 37 CINGHIE E MANICOTTI DENTATI POWER SNC

TIMING BELTS & SLEEVES POWER SINC 38 TIMING BELTS & SLEEVES POWER SINC

CINGHIE E MANICOTTI DENTATI TIMING BELTS & SLEEVES POWER SINC Lp. (mm) (mm) PROFILO MXL - PROFILE MXL L.Manic. Sleeve Width /Sleeve L=3,17mm Cod / Code 012 L=4,76mm Cod / Code 019 L=6,35mm Cod / Code 025 L=7,94mm Cod / Code 031 L=9,40mm Cod / Code 037 360 MXL 91,44 45 200 0,52 1,91 2,87 3,83 4,79 5,75 400 MXL 101,60 50 200 0,58 2,13 3,20 4,27 5,34 6,41 432 MXL 109,73 54 200 0,62 2,30 3,46 4,61 5,77 6,92 440 MXL 111,76 55 200 0,63 2,32 3,48 4,64 5,80 6,96 448 MXL 113,79 56 200 0,65 2,39 3,59 4,79 5,99 7,19 456 MXL 115,82 57 200 0,66 2,43 3,64 4,86 6,08 7,30 464 MXL 117,86 58 200 0,67 2,46 3,70 4,94 6,17 7,41 480 MXL 121,92 60 200 0,69 2,54 3,81 5,08 6,36 7,63 488 MXL 123,95 61 200 0,70 2,57 3,87 5,16 6,45 7,74 504 MXL 128,02 63 200 0,73 2,68 4,03 5,38 6,72 8,07 536 MXL 136,14 67 200 0,77 2,83 4,25 5,67 7,09 8,51 544 MXL 138,18 68 200 0,78 2,87 4,31 5,75 7,18 8,62 560 MXL 142,24 70 200 0,81 2,98 4,47 5,97 7,46 8,95 568 MXL 144,27 71 200 0,82 3,02 4,53 6,04 7,55 9,06 576 MXL 146,30 72 200 0,83 3,05 4,58 6,11 7,64 9,18 600 MXL 152,40 75 200 0,86 3,16 4,75 6,33 7,92 9,51 608 MXL 154,43 76 200 0,88 3,24 4,86 6,48 8,11 9,73 624 MXL 158,50 78 200 0,90 3,31 4,97 6,63 8,29 9,95 632 MXL 160,53 79 200 0,91 3,35 5,02 6,70 8,38 10,06 640 MXL 162,56 80 200 0,92 3,38 5,08 6,78 8,47 10,17 656 MXL 166,62 82 200 0,94 3,46 5,19 6,92 8,66 10,39 664 MXL 168,66 83 200 0,96 3,53 5,30 7,07 8,84 10,61 672 MXL 170,69 84 200 0,97 3,57 5,36 7,15 8,93 10,72 680 MXL 172,72 85 200 0,98 3,60 5,41 7,22 9,03 10,83 696 MXL 176,78 87 200 1,00 3,68 5,52 7,37 9,21 11,05 704 MXL 178,82 88 200 1,01 3,71 5,58 7,44 9,30 11,17 712 MXL 180,85 89 200 1,03 3,79 5,69 7,59 9,49 11,39 720 MXL 182,88 90 200 1,04 3,82 5,74 7,66 9,58 11,50 736 MXL 186,94 92 200 1,06 3,90 5,85 7,81 9,76 11,72 752 MXL 191,01 94 200 1,08 3,97 5,96 7,96 9,95 11,94 760 MXL 193,04 95 200 1,09 4,01 6,02 8,03 10,04 12,05 776 MXL 197,10 97 200 1,12 4,12 6,18 8,25 10,32 12,38 800 MXL 203,20 100 200 1,15 4,23 6,35 8,47 10,59 12,71 808 MXL 205,23 101 200 1,16 4,27 6,41 8,54 10,68 12,82 824 MXL 209,30 103 200 1,19 4,38 6,57 8,77 10,96 13,16 840 MXL 213,36 105 200 1,21 4,45 6,68 8,91 11,14 13,38 864 MXL 219,46 108 200 1,24 4,56 6,85 9,13 11,42 13,71 872 MXL 221,49 109 200 1,26 4,63 6,96 9,28 11,61 13,93 880 MXL 223,52 110 200 1,27 4,67 7,01 9,35 11,70 14,04 39 CINGHIE E MANICOTTI DENTATI - TIMING BELTS & SLEEVES POWER SINC

CINGHIE E MANICOTTI DENTATI TIMING BELTS & SLEEVES POWER SINC CINGHIE E MANICOTTI DENTATI - TIMING BELTS & SLEEVES POWER SINC 40 Lp. (mm) (mm) PROFILO MXL - PROFILE MXL L.Manic. Sleeve Width /Sleeve L=3,17mm Cod / Code 012 L=4,76mm Cod / Code 019 L=6,35mm Cod / Code 025 L=7,94mm Cod / Code 031 L=9,40mm Cod / Code 037 896 MXL 227,58 112 200 1,29 4,74 7,12 9,50 11,88 14,26 904 MXL 229,62 113 200 1,30 4,78 7,18 9,58 11,97 14,37 912 MXL 231,65 114 200 1,31 4,82 7,23 9,65 12,07 14,48 920 MXL 233,68 115 200 1,32 4,85 7,29 9,72 12,16 14,59 928 MXL 235,71 116 200 1,34 4,93 7,40 9,87 12,34 14,81 944 MXL 239,78 118 200 1,36 5,00 7,51 10,02 12,53 15,03 960 MXL 243,84 120 200 1,38 5,07 7,62 10,17 12,71 15,26 976 MXL 247,90 122 200 1,39 5,11 7,68 10,24 12,80 15,16 984 MXL 249,94 123 200 1,40 5,15 7,73 10,31 12,89 15,27 1000 MXL 254,00 125 200 1,41 5,18 7,79 10,39 12,99 15,37 1008 MXL 256,03 126 200 1,42 5,22 7,84 10,46 13,08 15,48 1040 MXL 264,16 130 200 1,43 5,26 7,90 10,53 13,17 15,59 1056 MXL 268,22 132 200 1,44 5,30 7,95 10,61 13,26 15,70 1064 MXL 270,26 133 200 1,45 5,33 8,01 10,68 13,36 15,81 1080 MXL 274,32 135 200 1,46 5,37 8,06 10,75 13,45 15,92 1120 MXL 284,48 140 200 1,47 5,41 8,12 10,83 13,54 16,25 1136 MXL 288,54 142 200 1,47 5,41 8,12 10,83 13,54 16,25 1184 MXL 300,74 148 200 1,53 5,63 8,45 11,27 14,09 16,91 1200 MXL 304,80 150 450 1,55 5,70 8,56 11,42 14,28 17,13 1224 MXL 310,90 153 450 1,58 5,81 8,72 11,64 14,55 17,47 1240 MXL 314,96 155 450 1,60 5,88 8,83 11,79 14,74 17,69 1280 MXL 325,12 160 450 1,65 6,07 9,11 12,15 15,20 18,24 1296 MXL 329,18 162 450 1,67 6,14 9,22 12,30 15,38 18,46 1320 MXL 335,28 165 450 1,70 6,25 9,39 12,52 15,66 18,79 1360 MXL 345,44 170 450 1,75 6,44 9,66 12,89 16,12 19,35 1400 MXL 355,60 175 450 1,81 6,66 9,99 13,33 16,67 20,01 1440 MXL 365,76 180 450 1,86 6,84 10,27 13,70 17,13 20,56 1472 MXL 373,89 184 450 1,90 6,99 10,49 14,00 17,50 21,00 1520 MXL 386,08 190 450 1,96 7,21 10,82 14,44 18,05 21,67 1600 MXL 406,40 200 450 2,06 7,58 11,37 15,17 18,97 22,77 1680 MXL 426,72 210 450 2,17 7,98 11,98 15,98 19,99 23,99 1768 MXL 449,07 221 450 2,28 8,38 12,59 16,79 21,00 25,20 1800 MXL 457,20 225 450 2,32 8,53 12,81 17,09 21,37 25,65 1888 MXL 479,55 236 450 2,44 8,97 13,47 17,97 22,47 26,97 1912 MXL 485,65 239 450 2,47 9,08 13,64 18,19 22,75 27,31 1920 MXL 487,68 240 450 2,48 9,12 13,69 18,27 22,84 27,42 2048 MXL 520,19 256 450 2,49 9,16 13,75 18,34 22,93 27,53 2120 MXL 538,48 265 450 2,58 9,49 14,25 19,00 23,76 28,52 2208 MXL 560,83 276 450 2,69 9,89 14,85 19,81 24,78 29,74

CINGHIE E MANICOTTI DENTATI TIMING BELTS & SLEEVES POWER SINC Lp. (mm) (mm) PROFILO MXL - PROFILE MXL L.Manic. Sleeve Width /Sleeve L=3,17mm Cod / Code 012 L=4,76mm Cod / Code 019 L=6,35mm Cod / Code 025 L=7,94mm Cod / Code 031 L=9,40mm Cod / Code 037 2240 MXL 568,96 280 450 2,73 10,04 15,07 20,11 25,14 30,18 2320 MXL 589,28 290 450 2,83 10,41 15,63 20,85 26,07 31,29 2480 MXL 629,92 310 450 3,02 11,11 16,68 22,25 27,82 33,39 2592 MXL 658,37 324 450 3,16 11,62 17,45 23,28 29,10 34,93 2776 MXL 705,10 347 450 3,38 12,43 18,66 24,90 31,13 37,37 2896 MXL 735,58 362 450 3,53 12,98 19,49 26,00 32,51 39,02 2976 MXL 755,90 372 450 3,62 13,31 19,99 26,66 33,34 40,02 3200 MXL 812,80 400 450 3,90 14,34 21,53 28,73 35,92 43,11 3392 MXL 861,57 424 450 4,13 15,19 22,80 30,42 38,04 45,66 3584 MXL 910,34 448 450 4,14 15,22 22,86 30,50 38,13 45,77 3624 MXL 920,50 453 450 4,15 15,26 22,91 30,57 38,22 45,88 3704 MXL 940,82 463 450 4,24 15,59 23,41 31,23 39,05 46,87 3984 MXL 1011,94 498 450 4,57 16,80 25,23 33,66 42,09 50,52 4032 MXL 1024,13 504 450 4,62 16,99 25,51 34,03 42,55 51,07 4368 MXL 1109,47 546 450 5,01 18,42 27,66 36,90 46,14 55,38 4560 MXL 1158,24 570 450 5,23 19,23 28,88 38,52 48,17 57,82 4664 MXL 1184,66 583 450 5,34 19,64 29,49 39,33 49,18 59,03 6080 MXL 1544,32 760 450 6,97 25,63 38,49 51,34 64,20 77,05 41 CINGHIE E MANICOTTI DENTATI - TIMING BELTS & SLEEVES POWER SINC

CINGHIE E MANICOTTI DENTATI TIMING BELTS & SLEEVES POWER SINC CINGHIE E MANICOTTI DENTATI - TIMING BELTS & SLEEVES POWER SINC 42 Lp. (mm) (mm) PROFILO XL - PROFILE XL L.Manic. Sleeve Width /Sleeve L=6,35mm Cod / Code 025 L=9,40mm Cod / Code 037 L=12,7mm Cod / Code 050 60 XL 152,4 30 200 0,29 2,14 3,16 4,27 70 XL 177,8 35 200 0,33 2,43 3,60 4,86 80 XL 203,2 40 200 0,38 2,80 4,14 5,60 90 XL 228,6 45 200 0,43 3,17 4,69 6,33 100 XL 254,0 50 450 0,48 3,54 5,23 7,07 102 XL 259,1 51 450 0,49 3,61 5,34 7,22 106 XL 269,2 53 450 0,51 3,76 5,56 7,51 110 XL 279,4 55 450 0,53 3,90 5,78 7,81 112 XL 284,5 56 450 0,54 3,98 5,89 7,96 120 XL 304,8 60 450 0,57 4,20 6,22 8,40 130 XL 330,2 65 450 0,62 4,57 6,76 9,13 140 XL 355,6 70 450 0,67 4,94 7,31 9,87 150 XL 381,0 75 450 0,72 5,30 7,85 10,61 156 XL 396,2 78 450 0,75 5,52 8,18 11,05 160 XL 406,4 80 450 0,77 5,67 8,40 11,34 170 XL 431,8 85 450 0,81 5,97 8,83 11,93 180 XL 457,2 90 450 0,86 6,33 9,38 12,67 182 XL 462,3 91 450 0,87 6,41 9,49 12,82 184 XL 467,4 92 450 0,88 6,48 9,60 12,96 190 XL 482,6 95 450 0,90 6,63 9,81 13,26 192 XL 487,7 96 450 0,91 6,70 9,92 13,41 198 XL 502,9 99 450 0,94 6,92 10,25 13,85 200 XL 508,0 100 450 0,95 7,00 10,36 14,00 202 XL 513,1 101 450 0,96 7,07 10,47 14,14 210 XL 533,4 105 450 0,97 7,15 10,58 14,29 220 XL 558,8 110 450 0,98 7,22 10,69 14,44 230 XL 584,2 115 450 1,02 7,51 11,12 15,03 240 XL 609,6 120 450 1,06 7,81 11,56 15,62 250 XL 635,0 125 450 1,08 7,96 11,78 15,91 260 XL 660,4 130 450 1,09 8,03 11,89 16,06 270 XL 685,8 135 450 1,10 8,10 11,99 16,21 276 XL 701,0 138 450 1,11 8,18 12,10 16,35 280 XL 711,2 140 450 1,13 8,32 12,32 16,65 290 XL 736,6 145 450 1,17 8,62 12,76 17,24 300 XL 762,0 150 450 1,21 8,91 13,19 17,83 316 XL 802,6 158 450 1,27 9,35 13,85 18,71 320 XL 812,8 160 450 1,29 9,50 14,07 19,00 330 XL 838,2 165 450 1,33 9,80 14,50 19,59 340 XL 863,6 170 450 1,37 10,09 14,94 20,18

CINGHIE E MANICOTTI DENTATI TIMING BELTS & SLEEVES POWER SINC Lp. (mm) (mm) PROFILO XL - PROFILE XL L.Manic. Sleeve Width /Sleeve L=6,35mm Cod / Code 025 L=9,40mm Cod / Code 037 L=12,7mm Cod / Code 050 344 XL 873,8 172 450 1,39 10,24 15,16 20,48 350 XL 889,0 175 450 1,41 10,39 15,37 20,77 360 XL 914,4 180 450 1,45 10,68 15,81 21,36 390 XL 990,6 195 450 1,57 11,56 17,12 23,13 434 XL 1102,4 217 450 1,75 12,89 19,08 25,78 Lp. (mm) (mm) 67 L** 171,4 18 200 0,32 98 L** 247,6 26 200 0,46 100 L** 257,1 27 450 0,48 109 L** 276,2 29 450 0,52 113 L** 285,7 30 450 0,54 120 L** 304,8 32 450 0,57 124 L 314,3 33 450 0,59 8,69 13,04 17,38 130 L** 333,3 35 450 0,62 135 L** 342,9 36 450 0,64 143 L** 361,9 38 450 0,68 150 L 381,0 40 450 0,71 10,46 15,69 20,92 154 L** 390,5 41 450 0,73 158 L** 400,0 42 450 0,75 160 L** 409,5 43 450 0,77 165 L** 419,1 44 450 0,79 169 L 429,3 45 450 0,80 11,79 17,68 23,57 173 L 482,2 46 450 0,82 12,08 18,12 24,16 177 L** 447,6 47 450 0,84 180 L** 457,2 48 450 0,86 185 L** 466,7 49 450 0,87 187 L 476,3 50 450 0,89 13,11 19,67 26,22 191 L** 485,7 51 450 0,91 195 L** 495,2 52 450 0,93 200 L** 504,8 53 450 0,95 203 L 513,1 54 450 0,96 14,14 21,21 28,29 206 L** 523,8 55 450 0,98 210 L 533,4 56 450 1,00 14,73 22,10 29,46 214 L** 542,9 57 450 1,02 217 L** 552,4 58 450 1,04 PROFILO L - PROFILE L L.Manic. Sleeve Width /Sleeve L=12,7mm Cod / Code 050 L=19,05mm Cod / Code 075 L=25,4mm Cod / Code 100 ** Misure disponibili NON a stock. Chiedere tempi di consega ** Not available in stock. Ask for delivery time 43 CINGHIE E MANICOTTI DENTATI - TIMING BELTS & SLEEVES POWER SINC

CINGHIE E MANICOTTI DENTATI TIMING BELTS & SLEEVES POWER SINC CINGHIE E MANICOTTI DENTATI - TIMING BELTS & SLEEVES POWER SINC 44 Lp. (mm) (mm) 220 L** 561,9 59 450 1,05 225 L 571,5 60 450 1,07 15,76 23,64 31,53 232 L** 590,5 62 450 1,11 236 L** 600,0 63 450 1,12 240 L 609,6 64 450 1,14 16,79 25,19 33,59 244 L** 619,1 65 450 1,16 248 L** 628,6 66 450 1,18 250 L** 638,1 67 450 1,20 255 L 647,7 68 450 1,21 17,83 26,74 35,65 259 L** 657,2 69 450 1,23 263 L** 666,7 70 450 1,25 270 L 685,8 72 450 1,29 19,00 28,51 38,01 275 L** 695,3 73 450 1,30 277 L** 704,8 74 450 1,32 280 L** 714,3 75 450 1,34 285 L 723,9 76 450 1,36 20,04 30,05 40,07 300 L 762,0 80 450 1,43 21,07 31,60 42,13 304 L** 771,4 81 450 1,45 315 L** 800,0 84 450 1,50 320 L** 809,5 85 450 1,52 322 L 819,1 86 450 1,54 22,69 34,03 45,37 330 L** 838,1 88 450 1,57 334 L** 847,6 89 450 1,59 337 L** 857,2 90 450 1,61 341 L** 866,7 91 450 1,62 345 L 876,2 92 450 1,62 23,87 35,80 47,73 352 L** 895,3 94 450 1,62 360 L** 914,3 96 450 1,62 367 L 933,4 98 450 1,63 24,01 36,02 48,03 371 L** 942,9 99 450 1,63 375 L** 952,4 100 450 1,63 382 L** 971,4 102 450 1,64 387 L** 981,0 103 450 1,64 390 L 990,5 104 450 1,65 24,31 36,46 48,62 394 L** 1000,0 105 450 1,65 397 L** 1009,5 106 450 1,66 405 L 1028,6 108 450 1,67 24,60 36,90 49,20 408 L** 1038,1 109 450 1,68 412 L** 1047,6 110 450 1,70 PROFILO L - PROFILE L L.Manic. Sleeve Width /Sleeve L=12,7mm Cod / Code 050 L=19,05mm Cod / Code 075 L=25,4mm Cod / Code 100 ** Misure disponibili NON a stock. Chiedere tempi di consega ** Not available in stock. Ask for delivery time

CINGHIE E MANICOTTI DENTATI TIMING BELTS & SLEEVES POWER SINC Lp. (mm) (mm) 420 L 1066,7 112 450 1,73 25,49 38,23 50,97 427 L** 1085,7 114 450 1,76 430 L** 1095,3 115 450 1,78 435 L** 1104,8 116 450 1,79 439 L** 1114,3 117 450 1,81 442 L** 1123,8 118 450 1,82 450 L 1142,9 120 450 1,85 27,25 40,88 54,51 453 L** 1152,4 121 450 1,87 461 L** 1171,5 123 450 1,90 465 L** 1181,0 124 450 1,92 480 L 1219,1 128 450 1,98 29,17 43,75 58,34 495 L** 1257,2 132 450 2,04 500 L** 1266,7 133 450 2,06 510 L 1295,3 136 450 2,10 30,94 46,41 61,87 525 L** 1333,4 140 450 2,16 540 L 1371,5 144 450 2,23 32,85 49,28 65,70 548 L** 1390,5 146 450 2,26 550 L** 1400,0 147 450 2,27 555 L** 1409,6 148 450 2,29 570 L** 1447,6 152 450 2,35 574 L** 1457,2 153 450 2,36 581 L** 1476,2 155 450 2,40 585 L** 1485,7 156 450 2,41 600 L 1523,8 160 450 2,47 36,39 54,58 72,78 619 L** 1571,5 165 450 2,55 630 L** 1600,0 168 450 2,60 634 L** 1609,6 169 450 2,61 660 L** 1676,2 176 450 2,72 694 L** 1761,9 185 450 2,86 697 L** 1771,5 186 450 2,87 720 L** 1828,6 192 450 2,97 728 L 1847,7 194 450 3,00 44,20 66,29 88,39 731 L** 1857,2 195 450 3,01 765 L** 1942,9 204 450 3,15 769 L** 1952,4 205 450 3,17 780 L** 1981,0 208 450 3,21 817 L** 2076,2 218 450 3,37 863 L** 2190,5 230 450 3,55 881 L** 2238,1 235 450 3,63 PROFILO L - PROFILE L L.Manic. Sleeve Width /Sleeve L=12,7mm Cod / Code 050 L=19,05mm Cod / Code 075 L=25,4mm Cod / Code 100 ** Misure disponibili NON a stock. Chiedere tempi di consega ** Not available in stock. Ask for delivery time 45 CINGHIE E MANICOTTI DENTATI - TIMING BELTS & SLEEVES POWER SINC

CINGHIE E MANICOTTI DENTATI TIMING BELTS & SLEEVES POWER SINC Lp. (mm) (mm) 900 L** 2285,8 240 450 3,71 915 L** 2323,9 244 450 3,77 934 L** 2371,5 249 450 3,85 994 L** 2523,9 265 450 4,10 1028 L** 2609,6 274 450 4,23 1043 L** 2647,7 278 450 4,30 1148 L** 2914,3 306 450 4,73 1192 L** 3028,6 318 450 4,91 1406 L** 3571,5 375 450 5,80 1418 L** 3600,1 378 450 5,84 1675 L** 4257,2 447 450 6,91 PROFILO L - PROFILE L L.Manic. Sleeve Width /Sleeve L=12,7mm Cod / Code 050 ** Misure disponibili NON a stock. Chiedere tempi di consega ** Not available in stock. Ask for delivery time L=19,05mm Cod / Code 075 L=25,4mm Cod / Code 100 CINGHIE E MANICOTTI DENTATI - TIMING BELTS & SLEEVES POWER SINC 46 Lp. (mm) (mm) PROFILO H - PROFILE H L.Manic. Sleeve Width /Sleeve L=19,05mm Cod / Code 075 L=25,4mm Cod / Code 100 L=38,1mm Cod / Code 150 L=50,8mm Cod / Code 200 L=76,2mm Cod / Code 300 145 H** 368,3 29 450 0,65 185 H** 469,9 37 450 0,83 200 H** 508,0 40 450 0,90 210 H** 533,4 42 450 0,94 220 H** 558,8 44 450 0,99 225 H** 571,5 45 450 1,01 230 H** 584,2 46 450 1,03 240 H 609,6 48 450 1,08 23,87 31,82 47,73 63,64 95,46 250 H** 635,0 50 450 1,12 255 H 647,7 51 450 1,15 25,41 33,88 50,83 67,77 101,65 260 H** 660,4 52 450 1,17 270 H 685,8 54 450 1,21 26,74 35,65 53,48 71,30 106,95 280 H** 711,2 56 450 1,26 285 H** 723,9 57 450 1,28 290 H** 736,6 58 450 1,30 300 H 762,0 60 450 1,35 29,83 39,78 59,66 79,55 119,33 310 H** 787,4 62 450 1,39 315 H** 800,1 63 450 1,42 320 H** 812,8 64 450 1,44 325 H** 825,5 65 450 1,46

CINGHIE E MANICOTTI DENTATI TIMING BELTS & SLEEVES POWER SINC Lp. (mm) (mm) 330 H 838,2 66 450 1,48 32,71 43,61 65,41 87,21 130,82 335 H** 850,9 67 450 1,51 340 H** 863,6 68 450 1,53 345 H** 876,3 69 450 1,55 350 H 889,0 70 450 1,57 34,80 46,40 69,61 92,80 139,22 355 H** 901,7 71 450 1,60 360 H 914,4 72 450 1,62 35,80 47,73 71,60 95,46 143,20 365 H** 927,1 73 450 1,64 370 H** 939,8 74 450 1,66 375 H** 952,5 75 450 1,69 380 H** 965,2 76 450 1,71 385 H** 977,9 77 450 1,72 390 H 990,6 78 450 1,73 38,23 50,97 76,46 101,95 152,92 395 H** 1003,3 79 450 1,74 400 H** 1016,0 80 450 1,75 405 H** 1028,7 81 450 1,75 410 H** 1041,4 82 450 1,76 415 H** 1054,1 83 450 1,76 420 H 1066,8 84 450 1,77 39,11 52,15 78,23 104,30 156,45 425 H** 1079,5 85 450 1,78 430 H 1092,2 86 450 1,79 39,56 52,74 79,11 105,48 158,22 435 H** 1104,9 87 450 1,80 440 H** 1117,6 88 450 1,82 445 H** 1130,3 89 450 1,84 450 H 1143,0 90 450 1,86 41,10 54,80 82,20 109,61 164,41 460 H** 1168,4 92 450 1,90 465 H** 1181,1 93 450 1,92 470 H** 1193,8 94 450 1,94 475 H** 1206,5 95 450 1,96 480 H 1219,2 96 450 1,98 43,75 58,34 87,51 116,68 175,02 485 H** 1231,9 97 450 2,01 490 H** 1244,6 98 450 2,03 500 H** 1270,0 100 450 2,07 505 H** 1282,7 101 450 2,09 510 H 1295,4 102 450 2,11 46,63 62,17 93,25 124,34 186,51 515 H** 1308,1 103 450 2,13 520 H** 1320,8 104 450 2,15 525 H** 1333,5 105 450 2,17 530 H** 1346,2 106 450 2,19 PROFILO H - PROFILE H L.Manic. Sleeve Width /Sleeve L=19,05mm Cod / Code 075 L=25,4mm Cod / Code 100 L=38,1mm Cod / Code 150 L=50,8mm Cod / Code 200 L=76,2mm Cod / Code 300 ** Misure disponibili NON a stock. Chiedere tempi di consega ** Not available in stock. Ask for delivery time 47 CINGHIE E MANICOTTI DENTATI - TIMING BELTS & SLEEVES POWER SINC

CINGHIE E MANICOTTI DENTATI TIMING BELTS & SLEEVES POWER SINC CINGHIE E MANICOTTI DENTATI - TIMING BELTS & SLEEVES POWER SINC 48 Lp. (mm) (mm) 540 H 1371,6 108 450 2,23 49,28 65,70 98,56 131,41 197,11 550 H** 1397,0 110 450 2,27 560 H 1422,4 112 450 2,32 51,27 68,36 102,53 136,71 205,07 565 H** 1435,1 113 450 2,34 570 H 1447,8 114 450 2,36 52,15 69,54 104,30 139,07 208,61 580 H** 1473,2 116 450 2,40 585 H** 1485,9 117 450 2,42 590 H** 1498,6 118 450 2,44 600 H 1524,0 120 450 2,48 54,80 73,07 109,61 146,14 219,21 605 H** 1536,7 121 450 2,50 610 H** 1549,4 122 450 2,52 615 H** 1562,1 123 450 2,54 625 H** 1587,5 125 450 2,58 630 H 1600,2 126 450 2,61 57,68 76,90 115,35 153,80 230,70 640 H** 1625,6 128 450 2,65 650 H 1651,0 130 450 2,69 59,44 79,26 118,89 158,52 237,77 660 H 1676,4 132 450 2,73 60,33 80,44 120,66 160,87 241,31 670 H** 1701,8 134 450 2,77 675 H** 1714,5 135 450 2,79 680 H 1727,2 136 450 2,81 62,10 82,79 124,19 165,59 248,38 690 H** 1752,6 138 450 2,85 700 H 1778,0 140 450 2,89 63,86 85,15 127,73 170,30 255,45 710 H** 1803,4 142 450 2,94 720 H** 1828,8 144 450 2,98 725 H 1841,5 145 450 3,00 66,29 88,39 132,59 176,78 265,18 730 H 1854,2 146 450 3,02 66,74 88,98 133,47 177,96 266,94 740 H** 1879,6 148 450 3,06 750 H 1905,0 150 450 3,10 68,50 91,34 137,01 182,68 274,02 760 H** 1930,4 152 450 3,14 770 H** 1955,8 154 450 3,18 780 H** 1981,2 156 450 3,23 790 H** 2006,6 158 450 3,27 800 H 2032,0 160 450 3,31 73,14 97,53 146,29 195,05 292,58 810 H** 2057,4 162 450 3,35 820 H** 2082,8 164 450 3,39 830 H** 2108,2 166 450 3,43 840 H** 2133,6 168 450 3,47 850 H 2159,0 170 450 3,51 77,56 103,42 155,13 206,84 310,26 860 H** 2184,4 172 450 3,56 PROFILO H - PROFILE H L.Manic. Sleeve Width /Sleeve L=19,05mm Cod / Code 075 L=25,4mm Cod / Code 100 L=38,1mm Cod / Code 150 L=50,8mm Cod / Code 200 L=76,2mm Cod / Code 300 ** Misure disponibili NON a stock. Chiedere tempi di consega ** Not available in stock. Ask for delivery time

CINGHIE E MANICOTTI DENTATI TIMING BELTS & SLEEVES POWER SINC Lp. (mm) (mm) 880 H** 2235,2 176 450 3,64 900 H 2286,0 180 450 3,72 82,20 109,61 164,41 219,21 328,82 920 H** 2336,8 184 450 3,80 930 H** 2362,2 186 450 3,85 950 H 2413,0 190 450 3,93 86,85 115,79 173,69 231,59 347,38 960 H** 2438,4 192 450 3,97 980 H** 2489,2 196 450 4,05 985 H** 2501,9 197 450 4,07 1000 H 2540,0 200 450 4,13 91,26 121,69 182,53 243,37 365,06 1020 H** 2590,8 204 450 4,22 1050 H** 2667,0 210 450 4,34 1070 H** 2717,8 214 450 4,42 1100 H 2794,0 220 450 4,55 100,55 134,06 201,09 268,12 402,18 1120 H 2844,8 224 450 4,63 102,31 136,42 204,63 272,84 409,25 1130 H** 2870,2 226 450 4,67 1140 H 2895,6 228 450 4,71 104,08 138,78 208,16 277,55 416,33 1150 H 2921,0 230 450 4,76 105,19 140,25 210,37 280,50 420,75 1160 H** 2946,4 232 450 4,80 1175 H** 2984,5 235 450 4,86 1180 H** 2997,2 236 450 4,88 1200 H** 3048,0 240 450 4,96 1250 H 3175,0 250 450 5,17 114,25 152,33 228,49 304,66 456,99 1260 H** 3200,4 252 450 5,21 1270 H** 3225,8 254 450 5,25 1300 H** 3302,0 260 450 5,38 1325 H** 3365,5 265 450 5,48 1350 H** 3429,0 270 450 5,58 1400 H 3556,0 280 450 5,79 127,95 170,60 255,89 341,19 511,79 1440 H** 3657,6 288 450 5,95 1450 H** 3683,0 290 450 6,00 1500 H** 3810,0 300 450 6,20 1510 H** 3835,4 302 450 6,24 1550 H** 3937,0 310 450 6,41 1535 H** 3898,9 307 450 6,35 1560 H** 3962,4 312 450 6,45 1600 H** 4064,0 320 450 6,62 1630 H** 4140,2 326 450 6,74 1660 H** 4216,4 332 450 6,86 PROFILO H - PROFILE H L.Manic. Sleeve Width /Sleeve L=19,05mm Cod / Code 075 L=25,4mm Cod / Code 100 L=38,1mm Cod / Code 150 L=50,8mm Cod / Code 200 L=76,2mm Cod / Code 300 ** Misure disponibili NON a stock. Chiedere tempi di consega ** Not available in stock. Ask for delivery time 1700 H 4318,0 340 450 7,03 155,35 207,13 310,70 414,26 621,40 49 CINGHIE E MANICOTTI DENTATI - TIMING BELTS & SLEEVES POWER SINC

CINGHIE E MANICOTTI DENTATI TIMING BELTS & SLEEVES POWER SINC Lp. (mm) (mm) PROFILO XH - PROFILE XH L.Manic. Sleeve Width /Sleeve L=50,8mm Cod / Code 200 L=76,2mm Cod / Code 300 L=101,6mm Cod / Code 400 507 XH 1289,0 58 440 5,42 319,39 479,08 638,78 560 XH 1422,4 64 440 5,98 352,39 528,58 704,78 630 XH 1600,2 72 440 6,72 396,00 593,99 791,99 700 XH 1778,0 80 440 7,47 440,19 660,29 880,38 770 XH 1955,8 88 440 8,22 484,39 726,58 968,78 840 XH 2133,6 96 440 8,96 527,99 791,99 1055,99 980 XH 2489,2 112 440 10,46 616,39 924,58 1232,77 1120 XH 2844,8 128 440 11,95 704,19 1056,28 1408,38 1260 XH 3200,4 144 440 13,45 792,58 1188,87 1585,16 1400 XH 3556,0 160 440 14,94 880,38 1320,58 1760,77 1540 XH 3911,6 176 440 16,43 968,19 1452,28 1936,37 1750 XH 4445,0 200 440 18,67 1100,19 1650,28 2200,37 CINGHIE E MANICOTTI DENTATI - TIMING BELTS & SLEEVES POWER SINC 50 Lp. (mm) (mm) PROFILO XXH - PROFILE XXH L.Manic. Sleeve Width /Sleeve L=50,8mm Cod / Code 200 700 XXH 1778,0 56 430 12,00 707,14 1060,70 1414,27 1767,84 800 XXH 2032,0 64 430 13,72 808,49 1212,74 1616,98 2021,23 900 XXH** 2286,0 72 280 15,43 909,26 1363,89 1818,52 2273,15 1000 XXH 2540,0 80 430 17,15 1010,62 1515,92 2021,23 2526,54 1200 XXH** 3048,0 96 430 20,57 1212,15 1818,22 2424,30 3030,37 1400 XXH** 3556,0 112 220 24,00 1414,27 2121,41 2828,54 3535,68 1600 XXH 4064,0 128 220 27,43 1616,40 2424,59 3232,79 4040,99 1800 XXH** 4572,0 144 220 30,86 1818,52 2727,78 3637,04 4546,30 ** Misure disponibili NON a stock. Chiedere tempi di consega ** Not available in stock. Ask for delivery time L=76,2mm Cod / Code 300 L=101,6mm Cod / Code 400 L=127mm Cod / Code 5 00

CINGHIE E MANICOTTI DENTATI POWER SINC HTD 51 CINGHIE E MANICOTTI DENTATI POWER SINC HTD

TIMING BELTS & SLEEVES POWER SINC HTD 52 TIMING BELTS & SLEEVES POWER SINC HTD

CINGHIE E MANICOTTI DENTATI SINC HTD TIMING BELTS & SLEEVES POWER SINC HTD Lp. (mm) (mm) PROFILO HTD 3M - PROFILE HTD 3M L.Manic. Sleeve Width /Sleeve L=3mm Cod / Code 03 L=6mm Cod / Code 06 L=9mm Cod / Code 09 L=12mm Cod / Code 12 L=15mm Cod / Code 15 111 3M 111 37 200 0,42 1,46 2,92 4,38 5,85 7,31 117 3M 117 39 200 0,44 1,53 3,06 4,59 6,12 7,66 120 3M 120 40 200 0,45 1,57 3,13 4,70 6,26 7,83 129 3M 129 43 200 0,49 1,71 3,41 5,12 6,82 8,53 141 3M 141 47 200 0,53 1,84 3,69 5,53 7,38 9,22 144 3M 144 48 200 0,54 1,88 3,76 5,64 7,52 9,40 150 3M 150 50 200 0,57 1,98 3,97 5,95 7,93 9,92 153 3M 153 51 200 0,58 2,02 4,04 6,06 8,07 10,09 156 3M 156 52 200 0,59 2,05 4,11 6,16 8,21 10,27 159 3M 159 53 200 0,60 2,09 4,18 6,26 8,35 10,44 162 3M 162 54 200 0,61 2,12 4,25 6,37 8,49 10,61 165 3M 165 55 200 0,62 2,16 4,33 6,49 8,65 10,81 168 3M 168 56 200 0,64 2,23 4,45 6,68 8,91 11,14 174 3M 174 58 200 0,66 2,30 4,59 6,89 9,19 11,48 177 3M 177 59 200 0,67 2,33 4,66 6,99 9,33 11,66 180 3M 180 60 200 0,68 2,37 4,73 7,10 9,47 11,83 186 3M 186 62 200 0,70 2,44 4,87 7,31 9,74 12,18 189 3M 189 63 200 0,71 2,47 4,94 7,41 9,88 12,35 192 3M 192 64 200 0,73 2,54 5,08 7,62 10,16 12,70 195 3M 195 65 200 0,74 2,58 5,15 7,73 10,30 12,88 201 3M 201 67 200 0,76 2,64 5,29 7,93 10,58 13,22 204 3M 204 68 200 0,77 2,68 5,36 8,04 10,72 13,40 207 3M 207 69 200 0,78 2,71 5,43 8,14 10,86 13,57 210 3M 210 70 200 0,79 2,75 5,50 8,25 11,00 13,75 213 3M 213 71 200 0,81 2,82 5,64 8,46 11,28 14,09 225 3M 225 75 200 0,85 2,96 5,92 8,87 11,83 14,79 237 3M 237 79 200 0,90 3,13 6,26 9,40 12,53 15,66 240 3M 240 80 200 0,91 3,17 6,33 9,50 12,67 15,83 246 3M 246 82 200 0,93 3,24 6,47 9,71 12,95 16,18 252 3M 252 84 200 0,95 3,31 6,61 9,92 13,22 16,53 255 3M 255 85 200 0,96 3,34 6,68 10,02 13,36 16,70 264 3M 264 88 200 1,00 3,48 6,96 10,44 13,92 17,40 267 3M 267 89 200 1,01 3,51 7,03 10,54 14,06 17,57 270 3M 270 90 200 1,02 3,55 7,10 10,65 14,20 17,75 276 3M 276 92 200 1,04 3,62 7,24 10,86 14,48 18,10 282 3M 282 94 200 1,07 3,72 7,45 11,17 14,89 18,62 285 3M 285 95 200 1,08 3,76 7,52 11,28 15,03 18,79 288 3M 288 96 200 1,09 3,79 7,59 11,38 15,17 18,97 291 3M 291 97 200 1,10 3,83 7,66 11,48 15,31 19,14 53 CINGHIE E MANICOTTI DENTATI SINC HTD - TIMING BELTS & SLEEVES POWER SINC HTD

CINGHIE E MANICOTTI DENTATI SINC HTD TIMING BELTS & SLEEVES POWER SINC HTD CINGHIE E MANICOTTI DENTATI SINC HTD - TIMING BELTS & SLEEVES POWER SINC HTD 54 Lp. (mm) (mm) PROFILO HTD 3M - PROFILE HTD 3M L.Manic. Sleeve Width /Sleeve L=3mm Cod / Code 03 L=6mm Cod / Code 06 L=9mm Cod / Code 09 L=12mm Cod / Code 12 L=15mm Cod / Code 15 297 3M 297 99 200 1,12 3,90 7,80 11,69 15,59 19,49 300 3M 300 100 450 1,13 3,93 7,86 11,80 15,73 19,66 309 3M 309 103 450 1,17 4,07 8,14 12,21 16,29 20,36 312 3M 312 104 450 1,18 4,11 8,21 12,32 16,43 20,53 318 3M 318 106 450 1,20 4,18 8,35 12,53 16,70 20,88 330 3M 330 110 450 1,25 4,35 8,70 13,05 17,40 21,75 333 3M 333 111 450 1,26 4,38 8,77 13,15 17,54 21,92 336 3M 336 112 450 1,27 4,42 8,84 13,26 17,68 22,10 339 3M 339 113 450 1,28 4,45 8,91 13,36 17,82 22,27 345 3M 345 115 450 1,30 4,52 9,05 13,57 18,10 22,62 357 3M 357 119 450 1,35 4,70 9,40 14,09 18,79 23,49 363 3M 363 121 450 1,37 4,77 9,54 14,30 19,07 23,84 366 3M 366 122 450 1,38 4,80 9,60 14,41 19,21 24,01 384 3M 384 128 450 1,45 5,05 10,09 15,14 20,18 25,23 390 3M 390 130 450 1,47 5,12 10,23 15,35 20,46 25,58 393 3M 393 131 450 1,49 5,19 10,37 15,56 20,74 25,93 420 3M 420 140 450 1,59 5,53 11,07 16,60 22,13 27,67 426 3M 426 142 450 1,61 5,60 11,21 16,81 22,41 28,01 447 3M 447 149 450 1,69 5,88 11,76 17,64 23,52 29,41 474 3M 474 158 450 1,79 6,23 12,46 18,69 24,92 31,15 477 3M 477 159 450 1,80 6,26 12,53 18,79 25,06 31,32 480 3M 480 160 450 1,81 6,30 12,60 18,90 25,20 31,49 486 3M 486 162 450 1,82 6,33 12,67 19,00 25,33 31,67 495 3M 495 165 450 1,83 6,37 12,74 19,11 25,47 31,84 501 3M 501 167 450 1,84 6,40 12,81 19,21 25,61 32,02 513 3M 513 171 450 1,85 6,44 12,88 19,31 25,75 32,19 522 3M 522 174 450 1,86 6,47 12,95 19,42 25,89 32,36 531 3M 531 177 450 1,87 6,51 13,02 19,52 26,03 32,54 537 3M 537 179 450 1,88 6,54 13,08 19,63 26,17 32,71 558 3M 558 186 450 1,89 6,58 13,15 19,73 26,31 32,89 564 3M 564 188 450 1,90 6,61 13,22 19,84 26,45 33,06 597 3M 597 199 450 2,01 6,99 13,99 20,98 27,98 34,97 606 3M 606 202 450 2,04 7,10 14,20 21,30 28,40 35,50 612 3M 612 204 450 2,07 7,20 14,41 21,61 28,81 36,02 633 3M 633 211 450 2,14 7,45 14,89 22,34 29,79 37,24 669 3M 669 223 450 2,26 7,86 15,73 23,59 31,46 39,32 708 3M 708 236 450 2,39 8,32 16,63 24,95 33,27 41,59 711 3M 711 237 450 2,40 8,35 16,70 25,06 33,41 41,76 750 3M 750 250 450 2,53 8,80 17,61 26,41 35,22 44,02

CINGHIE E MANICOTTI DENTATI SINC HTD TIMING BELTS & SLEEVES POWER SINC HTD Lp. (mm) (mm) PROFILO HTD 3M - PROFILE HTD 3M L.Manic. Sleeve Width /Sleeve L=3mm Cod / Code 03 L=6mm Cod / Code 06 L=9mm Cod / Code 09 753 3M 753 251 450 2,54 8,84 17,68 26,52 35,36 44,20 804 3M 804 268 450 2,71 9,43 18,86 28,29 37,72 47,15 813 3M 813 271 450 2,74 9,54 19,07 28,61 38,14 47,68 843 3M 843 281 450 2,84 9,88 19,77 29,65 39,53 49,42 885 3M 885 295 450 2,99 10,41 20,81 31,22 41,62 52,03 939 3M 939 313 450 3,17 11,03 22,06 33,09 44,13 55,16 1125 3M 1125 375 450 3,80 13,22 26,45 39,67 52,90 66,12 1245 3M 1245 415 450 4,20 14,62 29,23 43,85 58,46 73,08 1263 3M 1263 421 450 4,26 14,82 29,65 44,47 59,30 74,12 Altre misure disponibili a richiesta - Other size on demand L=12mm Cod / Code 12 L=15mm Cod / Code 15 Lp. (mm) (mm) PROFILO HTD 5M - PROFILE HTD 5M L.Manic. Sleeve Width /Sleeve L=9mm Cod / Code 09 L=15mm Cod / Code 15 L=25mm Cod / Code 25 225-5M 225 45 150 0,75 7,83 13,05 21,75 255-5M 255 51 200 0,85 8,87 14,79 24,65 265 5M 265 53 200 0,88 9,19 15,31 25,52 280 5M 280 56 450 0,93 9,71 16,18 26,97 300 5M 300 60 450 1,00 10,44 17,40 29,00 305 5M 305 61 450 1,01 10,54 17,57 29,29 325 5M 325 65 450 1,08 11,28 18,79 31,32 340 5M 340 68 450 1,13 11,80 19,66 32,77 350 5M 350 70 450 1,16 12,11 20,18 33,64 360 5M 360 72 450 1,19 12,42 20,71 34,51 365 5M 365 73 200 1,21 12,63 21,05 35,09 375 5M 375 75 450 1,24 12,95 21,58 35,96 400-5M 400 80 450 1,33 13,89 23,14 38,57 425 5M 425 85 450 1,41 14,72 24,53 40,89 450-5M 450 90 200 1,43 14,93 24,88 41,47 475 5M 475 95 450 1,51 15,76 26,27 43,79 500 5M 500 100 450 1,58 16,50 27,49 45,82 520 5M 520 104 450 1,65 17,23 28,71 47,85 525 5M 525 105 450 1,66 17,33 28,88 48,14 535 5M 535 107 450 1,70 17,75 29,58 49,30 550 5M 550 110 450 1,74 18,17 30,28 50,46 565 5M 565 113 450 1,79 18,69 31,15 51,91 580 5M 580 116 450 1,84 19,21 32,02 53,36 600 5M 600 120 450 1,90 19,84 33,06 55,10 55 CINGHIE E MANICOTTI DENTATI SINC HTD - TIMING BELTS & SLEEVES POWER SINC HTD

CINGHIE E MANICOTTI DENTATI SINC HTD TIMING BELTS & SLEEVES POWER SINC HTD CINGHIE E MANICOTTI DENTATI SINC HTD - TIMING BELTS & SLEEVES POWER SINC HTD 56 610 5M 610 122 450 1,93 20,15 33,58 55,97 635 5M 635 127 450 2,01 20,98 34,97 58,29 670 5M 670 134 450 2,12 22,13 36,89 61,48 700 5M 700 140 450 2,22 23,18 38,63 64,38 710 5M 710 142 450 2,25 23,49 39,15 65,25 740 5M 740 148 450 2,35 24,53 40,89 68,15 750 5M 750 150 450 2,38 24,85 41,41 69,02 755 5M 755 151 450 2,39 24,95 41,59 69,31 800 5M 800 160 450 2,54 26,52 44,20 73,66 825 5M 825 165 450 2,55 26,62 44,37 73,95 835 5M 835 167 450 2,56 26,73 44,54 74,24 860 5M 860 172 450 2,57 26,83 44,72 74,53 890 5M 890 178 450 2,58 26,94 44,89 74,82 900 5M 900 180 450 2,59 27,04 45,07 75,11 925 5M 925 185 450 2,60 27,14 45,24 75,40 950 5M 950 190 450 2,66 27,77 46,28 77,14 1000 5M 1000 200 450 2,80 29,23 48,72 81,20 1035 5M 1035 207 450 2,89 30,17 50,29 83,81 1050 5M 1050 210 450 2,93 30,59 50,98 84,97 1125 5M 1125 225 450 3,14 32,78 54,64 91,06 1350 5M 1350 270 450 3,77 39,36 65,60 109,33 1420 5M 1420 284 450 3,97 41,45 69,08 115,13 1595 5M 1595 319 450 4,46 46,56 77,60 129,34 1790 5M 1790 358 450 5,00 52,20 87,00 145,00 1895 5M 1895 379 450 5,29 55,26 92,10 153,50 Lp. (mm) (mm) Lp. (mm) (mm) Altre misure disponibili a richiesta - Other size on demand 184-8M** 184 23 440 0,45 288-8M** 288 36 440 0,70 328-8M** 328 41 440 0,80 336-8M** 336 42 440 0,82 368-8M** 368 46 440 0,90 376-8M** 376 47 440 0,92 384-8M** 384 48 440 0,94 400-8M** 400 50 440 0,98 PROFILO HTD 5M - PROFILE HTD 5M L.Manic. Sleeve Width /Sleeve L=9mm Cod / Code 09 L=15mm Cod / Code 15 PROFILO HTD 8M - PROFILE HTD 8 L.Manic. Sleeve Width /Sleeve L=20mm Cod / Code 20 L=30mm Cod / Code 30 L=25mm Cod / Code 25 L=50mm Cod / Code 50 L=85mm Cod / Code 85

CINGHIE E MANICOTTI DENTATI SINC HTD TIMING BELTS & SLEEVES POWER SINC HTD Lp. (mm) (mm) PROFILO HTD 8M - PROFILE HTD 8 L.Manic. Sleeve Width /Sleeve 408-8M** 408 51 440 1,00 416-8M** 416 52 440 1,02 424 8M 424 53 440 1,03 23,90 35,84 59,74 101,56 440-8M** 440 55 440 1,07 448-8M** 448 56 440 1,09 472-8M** 472 59 440 1,15 480 8M 480 60 440 1,17 27,14 40,72 67,86 115,36 512-8M** 512 64 440 1,25 520-8M** 520 65 440 1,27 536-8M** 536 67 440 1,31 544-8M** 544 68 440 1,33 560 8M 560 70 440 1,37 31,78 47,68 79,46 135,08 568-8M** 568 71 440 1,39 576-8M** 576 72 440 1,41 584-8M** 584 73 440 1,42 600 8M 600 75 440 1,46 33,87 50,81 84,68 143,96 624 8M** 624 78 440 1,52 632 8M 632 79 440 1,54 35,73 53,59 89,32 151,84 640 8M 640 80 440 1,56 36,19 54,29 90,48 153,82 656 8M 656 82 440 1,60 37,12 55,68 92,80 157,76 672-8M** 672 84 440 1,64 680-8M** 680 85 440 1,66 688-8M** 688 86 440 1,68 696-8M** 696 87 440 1,70 712-8M** 712 89 440 1,74 720 8M 720 90 440 1,76 40,83 61,25 102,08 173,54 728-8M** 728 91 440 1,78 736-8M** 736 92 440 1,80 760-8M 760 95 440 1,85 42,95 64,41 107,36 182,51 776 8M 776 97 440 1,89 43,85 65,77 109,62 186,35 784-8M** 784 98 440 1,91 792-8M** 792 99 440 1,93 800 8M 800 100 440 1,95 45,24 67,86 113,10 192,27 816-8M** 816 102 440 1,99 824-8M** 824 103 440 2,01 840 8M 840 105 440 2,05 47,56 71,34 118,90 202,13 848-8M** 848 106 440 2,07 856-8M 856 107 440 2,09 48,47 72,70 121,16 205,98 864-8M** 864 108 440 2,11 L=20mm Cod / Code 20 L=30mm Cod / Code 30 L=50mm Cod / Code 50 L=85mm Cod / Code 85 ** Misure disponibili NON a stock. Chiedere tempi di consega ** Not available in stock. Ask for delivery time 57 CINGHIE E MANICOTTI DENTATI SINC HTD - TIMING BELTS & SLEEVES POWER SINC HTD

CINGHIE E MANICOTTI DENTATI SINC HTD TIMING BELTS & SLEEVES POWER SINC HTD CINGHIE E MANICOTTI DENTATI SINC HTD - TIMING BELTS & SLEEVES POWER SINC HTD 58 Lp. (mm) (mm) PROFILO HTD 8M - PROFILE HTD 8 L.Manic. Sleeve Width /Sleeve 872-8M** 872 109 440 2,13 880 8M 880 110 440 2,15 49,88 74,82 124,70 211,99 896-8M 896 112 440 2,19 50,79 76,18 126,97 215,84 912-8M** 912 114 440 2,23 920 8M 920 115 440 2,24 51,97 77,95 129,92 220,86 928-8M** 928 116 440 2,26 936-8M** 936 117 440 2,28 952-8M** 952 119 440 2,32 960 8M 960 120 440 2,34 54,29 81,43 135,72 230,72 968-8M** 968 121 440 2,36 976-8M** 976 122 440 2,38 984-8M** 984 123 440 2,40 1000 8M 1000 125 440 2,44 56,61 84,91 141,52 240,58 1008-8M** 1008 126 440 2,46 1016-8M** 1016 127 440 2,48 1032-8M** 1032 129 440 2,52 1040 8M 1040 130 440 2,54 58,93 88,39 147,32 250,44 1056-8M** 1056 132 440 2,58 1064-8M** 1064 133 440 2,60 1072-8M** 1072 134 440 2,62 1080-8M** 1080 135 440 2,64 1104-8M** 1104 138 440 2,69 1120 8M 1120 140 440 2,73 63,34 95,00 158,34 269,18 1128-8M** 1128 141 440 2,75 1136-8M** 1136 142 440 2,77 1144-8M** 1144 143 440 2,79 1152-8M** 1152 144 440 2,81 1160-8M** 1160 145 440 2,83 1168-8M** 1168 146 440 2,85 1176-8M** 1176 147 440 2,87 1184-8M 1184 148 440 2,89 67,07 100,60 167,67 285,05 1192-8M** 1192 149 440 2,91 1200 8M 1200 150 440 2,93 67,98 101,96 169,94 288,90 1208-8M** 1208 151 440 2,95 1216-8M** 1216 152 440 2,97 1224 8M 1224 153 440 2,99 69,37 104,05 173,42 294,81 1232-8M** 1232 154 440 3,01 1240-8M** 1240 155 440 3,03 1248-8M** 1248 156 440 3,05 L=20mm Cod / Code 20 L=30mm Cod / Code 30 L=50mm Cod / Code 50 L=85mm Cod / Code 85 ** Misure disponibili NON a stock. Chiedere tempi di consega ** Not available in stock. Ask for delivery time

CINGHIE E MANICOTTI DENTATI SINC HTD TIMING BELTS & SLEEVES POWER SINC HTD Lp. (mm) (mm) PROFILO HTD 8M - PROFILE HTD 8 L.Manic. Sleeve Width /Sleeve 1256 8M 1256 157 440 3,06 70,99 106,49 177,48 301,72 1264-8M** 1264 158 440 3,08 1272-8M** 1272 159 440 3,10 1280 8M 1280 160 440 3,12 72,38 108,58 180,96 307,63 1296-8M** 1296 162 440 3,16 1304-8M** 1304 163 440 3,18 1312-8M** 1312 164 440 3,20 1320-8M** 1320 165 440 3,22 1328-8M** 1328 166 440 3,24 1344-8M** 1344 168 440 3,28 1360 8M 1360 170 440 3,32 77,02 115,54 192,56 327,35 1392 8M** 1392 174 440 3,40 1400-8M** 1400 175 440 3,42 1408-8M** 1408 176 440 3,44 1416-8M** 1416 177 440 3,45 1424-8M** 1424 178 440 3,46 1432-8M** 1432 179 440 3,47 1440 8M 1440 180 440 3,48 80,74 121,10 201,84 343,13 1456 8M 1456 182 440 3,49 80,97 121,45 202,42 344,11 1480-8M** 1480 185 440 3,50 1488-8M** 1488 186 440 3,51 1512-8M** 1512 189 440 3,52 1520-8M** 1520 190 440 3,53 1536-8M** 1536 192 440 3,57 1552-8M** 1552 194 440 3,60 1560-8M** 1560 195 440 3,62 1576-8M** 1576 197 440 3,66 1600 8M 1600 200 440 3,71 86,07 129,11 215,18 365,81 1608-8M** 1608 201 440 3,73 1632-8M** 1632 204 440 3,79 1640-8M** 1640 205 440 3,81 1648-8M** 1648 206 440 3,83 1656-8M** 1656 207 440 3,84 1680-8M** 1680 210 440 3,90 1696-8M** 1696 212 440 3,94 1728-8M** 1728 216 440 4,01 1760 8M 1760 220 440 4,09 94,89 142,33 237,22 403,27 1784-8M** 1784 223 440 4,14 1792-8M** 1792 224 440 4,16 L=20mm Cod / Code 20 L=30mm Cod / Code 30 L=50mm Cod / Code 50 L=85mm Cod / Code 85 ** Misure disponibili NON a stock. Chiedere tempi di consega ** Not available in stock. Ask for delivery time 59 CINGHIE E MANICOTTI DENTATI SINC HTD - TIMING BELTS & SLEEVES POWER SINC HTD

CINGHIE E MANICOTTI DENTATI SINC HTD TIMING BELTS & SLEEVES POWER SINC HTD CINGHIE E MANICOTTI DENTATI SINC HTD - TIMING BELTS & SLEEVES POWER SINC HTD 60 Lp. (mm) (mm) PROFILO HTD 8M - PROFILE HTD 8 L.Manic. Sleeve Width /Sleeve 1800 8M 1800 225 440 4,18 96,98 145,46 242,44 412,15 1824-8M** 1824 228 440 4,23 1840-8M** 1840 230 440 4,27 1856-8M** 1856 232 440 4,31 1888-8M** 1888 236 440 4,38 1896-8M** 1896 237 440 4,40 1904-8M** 1904 238 440 4,42 1936-8M** 1936 242 440 4,49 1944-8M** 1944 243 440 4,51 1952-8M** 1952 244 440 4,53 1960-8M** 1960 245 440 4,55 2000 8M 2000 250 440 4,64 107,65 161,47 269,12 457,50 2016-8M** 2016 252 440 4,68 2032-8M** 2032 254 440 4,72 2048-8M** 2048 256 440 4,75 2056-8M** 2056 257 440 4,77 2080-8M 2080 260 440 4,83 111,96 167,93 279,88 475,80 2088-8M** 2088 261 440 4,85 2096-8M** 2096 262 440 4,87 2104-8M** 2104 263 440 4,88 2136-8M** 2136 267 440 4,96 2160-8M** 2160 270 440 5,01 2168-8M** 2168 271 440 5,03 2184-8M** 2184 273 440 5,07 2200-8M** 2200 275 440 5,11 2208-8M** 2208 276 440 5,13 2224-8M** 2224 278 440 5,16 2240-8M** 2240 280 440 5,20 2248-8M 2248 281 440 5,22 121,04 181,56 302,60 514,42 2272-8M** 2272 284 440 5,27 2304-8M** 2304 288 440 5,35 2312-8M** 2312 289 440 5,37 2328-8M** 2328 291 440 5,40 2392-8M** 2392 299 440 5,55 2400 8M 2400 300 440 5,57 129,22 193,84 323,06 549,20 2464-8M** 2464 308 440 5,72 2504-8M** 2504 313 440 5,81 2560-8M** 2560 320 440 5,94 2584-8M** 2584 323 440 6,00 L=20mm Cod / Code 20 L=30mm Cod / Code 30 L=50mm Cod / Code 50 L=85mm Cod / Code 85 ** Misure disponibili NON a stock. Chiedere tempi di consega ** Not available in stock. Ask for delivery time

CINGHIE E MANICOTTI DENTATI SINC HTD TIMING BELTS & SLEEVES POWER SINC HTD 2600 8M 2600 325 440 6,04 140,13 210,19 350,32 595,54 2736-8M** 2736 342 440 6,35 2800 8M 2800 350 440 6,50 150,80 226,20 377,00 640,90 3048 8M 3048 381 440 7,08 164,26 246,38 410,64 698,09 3120 8M 3120 390 440 7,24 167,97 251,95 419,92 713,86 3168 8M** 3168 396 440 7,35 3200 8M 3200 400 440 7,43 172,38 258,56 430,94 732,60 3280 8M 3280 410 440 7,61 176,55 264,83 441,38 750,35 3400 8M 3400 425 440 7,89 183,05 274,57 457,62 777,95 3600 8M 3600 450 440 8,36 193,95 290,93 484,88 824,30 3824 8M** 3824 478 440 8,88 4000 8M 4000 500 440 9,29 215,53 323,29 538,82 915,99 4200 8M 4200 525 440 9,75 226,20 339,30 565,50 961,35 4400 8M 4400 550 440 10,21 236,87 355,31 592,18 1006,71 5120 8M 5120 640 440 11,89 275,85 413,77 689,62 1172,35 5600 8M 5600 700 440 13,00 301,60 452,40 754,00 1281,80 5960 8M 5960 745 240 13,84 321,09 481,63 802,72 1364,62 6600 8M 6600 825 210 15,32 355,42 533,14 888,56 1510,55 6880 8M 6880 860 440 15,97 370,50 555,76 926,26 1574,64 Lp. (mm) (mm) Lp. (mm) (mm) PROFILO HTD 8M - PROFILE HTD 8 L.Manic. Sleeve Width /Sleeve 826-14M** 826 59 440 2,86 924-14M** 924 66 440 3,19 938-14M** 938 67 440 3,24 966 14M 966 69 440 3,34 154,98 213,09 329,32 445,56 658,65 1036-14M** 1036 74 440 3,58 1050-14M** 1050 75 440 3,63 1064-14M** 1064 76 440 3,68 1078-14M** 1078 77 440 3,73 1092-14M** 1092 78 440 3,77 1120-14M** 1120 80 440 3,87 1134-14M** 1134 81 440 3,92 1148-14M** 1148 82 440 3,97 1190 14M 1190 85 440 4,11 190,70 262,22 405,25 548,27 810,49 1246-14M** 1246 89 440 4,31 L=20mm Cod / Code 20 L=30mm Cod / Code 30 PROFILO HTD 14M - PROFILE HTD 14 M L.Manic. Sleeve Width /Sleeve L=40mm Cod / Code 40 L=55mm Cod / Code 55 L=50mm Cod / Code 50 L=85mm Cod / Code 85 L=85mm Cod / Code 85 L=115mm Cod / Code 115 L=170mm Cod / Code 170 61 CINGHIE E MANICOTTI DENTATI SINC HTD - TIMING BELTS & SLEEVES POWER SINC HTD

CINGHIE E MANICOTTI DENTATI SINC HTD TIMING BELTS & SLEEVES POWER SINC HTD CINGHIE E MANICOTTI DENTATI SINC HTD - TIMING BELTS & SLEEVES POWER SINC HTD 62 Lp. (mm) (mm) 1260-14M** 1260 90 440 4,36 1288-14M** 1288 92 440 4,45 1344-14M** 1344 96 440 4,65 1358-14M** 1358 97 440 4,69 1400 14M 1400 100 440 4,84 224,58 308,79 477,22 645,66 954,45 1456-14M** 1456 104 440 4,79 1498-14M** 1498 107 440 4,93 1512 14M 1512 108 440 4,98 231,07 317,72 491,03 664,33 982,06 1540 14M 1540 110 440 5,07 235,25 323,47 499,90 676,34 999,80 1568-14M** 1568 112 440 5,16 1610 14M 1610 115 440 5,30 245,92 338,14 522,58 707,02 1045,16 1638-14M** 1638 117 440 5,39 1652-14M** 1652 118 440 5,44 1680-14M** 1680 120 440 5,53 1736-14M** 1736 124 440 5,71 1750-14M** 1750 125 440 5,76 1778 14M 1778 127 440 5,85 271,44 373,23 576,81 780,39 1153,62 1806-14M 1806 129 440 5,94 275,71 379,11 585,89 792,68 1171,79 1820-14M** 1820 130 440 5,99 1890 14M 1890 135 440 6,22 288,61 396,84 613,29 829,75 1226,58 1904-14M** 1904 136 440 6,27 1932-14M** 1932 138 440 6,36 1946-14M** 1946 139 440 6,41 1988-14M** 1988 142 440 6,54 2002-14M 2002 143 440 6,59 305,66 420,29 649,53 878,77 1299,06 2044-14M** 2044 146 440 6,73 2100 14M 2100 150 440 6,91 320,62 440,86 681,33 921,79 1362,65 2198-14M** 2198 157 440 7,24 2240-14M** 2240 160 440 7,37 2310 14M 2310 165 440 7,60 352,64 484,88 749,36 1013,84 1498,72 2380 14M 2380 170 440 7,83 363,29 499,54 772,01 1044,48 1544,02 2450 14M 2450 175 440 8,06 373,98 514,23 794,72 1075,20 1589,43 2590 14M 2590 185 440 8,53 395,79 544,21 841,06 1137,90 1682,12 2660 14M 2660 190 440 8,76 406,49 558,92 863,79 1168,65 1727,58 2800 14M 2800 200 440 9,22 427,81 588,24 909,09 1229,95 1818,18 3150 14M 3150 225 440 10,10 468,64 644,38 995,86 1347,34 1991,72 3360 14M** 3360 240 440 10,77 PROFILO HTD 14M - PROFILE HTD 14 M L.Manic. Sleeve Width /Sleeve L=40mm Cod / Code 40 L=55mm Cod / Code 55 L=85mm Cod / Code 85 L=115mm Cod / Code 115 L=170mm Cod / Code 170 ** Misure disponibili NON a stock. Chiedere tempi di consega ** Not available in stock. Ask for delivery time 3500 14M 3500 250 440 11,22 520,61 715,84 1106,29 1496,75 2212,58 3850 14M 3850 275 440 12,34 572,58 787,29 1216,72 1646,16 2433,45

CINGHIE E MANICOTTI DENTATI SINC HTD TIMING BELTS & SLEEVES POWER SINC HTD Lp. (mm) (mm) PROFILO HTD 14M - PROFILE HTD 14 M L.Manic. Sleeve Width /Sleeve L=40mm Cod / Code 40 L=55mm Cod / Code 55 L=85mm Cod / Code 85 L=115mm Cod / Code 115 L=170mm Cod / Code 170 4326 14M 4326 309 440 13,87 643,57 884,91 1367,58 1850,26 2735,16 4578 14M 4578 327 440 14,68 681,15 936,58 1447,45 1958,31 2894,90 4760 14M 4760 340 210 15,26 708,06 973,59 1504,64 2035,68 3009,27 4956 14M 4956 354 430 15,89 737,30 1013,78 1566,75 2119,73 3133,51 5040 14M 5040 360 430 16,16 749,82 1031,01 1593,38 2155,74 3186,75 6160 14M 6160 440 430 19,75 916,40 1260,05 1947,35 2634,65 3894,70 6860 14M 6860 490 430 21,99 1020,34 1402,96 2168,21 2933,47 4336,43 ** Misure disponibili NON a stock. Chiedere tempi di consega ** Not available in stock. Ask for delivery time 63 CINGHIE E MANICOTTI DENTATI SINC HTD - TIMING BELTS & SLEEVES POWER SINC HTD

CINGHIE E MANICOTTI DENTATI DOPPIA DENTATURA POWER SINC DD 64 CINGHIE E MANICOTTI DENTATI - DOPPIA DENTATURA POWER SINC DD

TIMING BELTS & SLEEVES POWER SINC DD DOUBLE SIDE 65 TIMING BELTS & SLEEVES - POWER SINC DD DOUBLE SIDE

CINGHIE E MANICOTTI DOPPIA DENTATURA DOUBLE SIDE TIMING BELTS & SLEEVES POWER SINC DD 66 PROFILO L DOPPIA DENTATURA - PROFILE L DOUBLE SIDE Lp. (mm) (mm) L.Manic. Sleeve Width /Sleeve L=12,7mm Cod / Code 50 L=19,05mm Cod / Code 75 L=25,4mm Cod / Code 100 210 DL 533,4 56 180 3,81 56,13 84,19 112,26 225 DL 571,5 60 180 4,08 60,11 90,16 120,21 240 DL 609,6 64 180 4,35 64,08 96,13 128,17 255 DL 647,7 68 180 4,63 68,21 102,31 136,42 270 DL 685,8 72 180 4,90 72,19 108,28 144,37 285 DL 723,9 76 180 5,17 76,16 114,25 152,33 300 DL 762,0 80 180 5,44 80,14 120,21 160,28 322 DL 819,2 86 180 5,84 86,03 129,05 172,07 345 DL 876,3 92 180 6,26 92,22 138,33 184,44 367 DL 933,5 98 180 6,30 92,81 139,22 185,62 390 DL 990,6 104 180 6,33 93,25 139,88 186,51 420 DL 1066,8 112 180 6,82 100,47 150,71 200,94 450 DL 1143,0 120 180 7,30 107,54 161,32 215,09 480 DL 1219,2 128 180 7,79 114,76 172,14 229,52 510 DL 1295,4 136 180 8,28 121,98 182,97 243,96 540 DL 1371,6 144 180 8,76 129,05 193,58 258,10 600 DL 1524,0 160 180 9,74 143,49 215,23 286,98 CINGHIE E MANICOTTI DD - DOUBLE SIDE TIMING BELTS & SLEEVES POWER SINC DD PROFILO H DOPPIA DENTATURA - PROFILE H DOUBLE SIDE Lp. (mm) (mm) L.Manic. Sleeve Width /Sleeve L=19,05mm Cod / Code 75 L=25,4mm Cod / Code 100 L=38,1mm Cod / Code 150 L=50,8mm Cod / Code 200 L=76,2mm Cod / Code 300 330 DH 838,2 66 200 5,77 127,51 170,01 255,01 340,01 510,02 360 DH 914,4 72 200 6,30 139,22 185,62 278,43 371,25 556,87 390 DH 990,6 78 200 6,82 150,71 200,94 301,42 401,89 602,83 420 DH 1066,8 84 200 6,90 152,48 203,30 304,95 406,60 609,90 450 DH 1143,0 90 200 7,00 154,69 206,25 309,37 412,50 618,74 480 DH 1219,2 96 200 7,46 164,85 219,80 329,70 439,60 659,40 510 DH 1295,4 102 200 7,93 175,24 233,65 350,47 467,30 700,95 540 DH 1371,6 108 200 8,40 185,62 247,50 371,25 495,00 742,49 570 DH 1447,8 114 200 8,86 195,79 261,05 391,58 522,10 783,15 600 DH 1524,0 120 200 9,33 206,17 274,90 412,35 549,80 824,70 630 DH 1600,2 126 200 9,80 216,56 288,75 433,12 577,49 866,24 660 DH 1676,4 132 200 10,26 226,73 302,30 453,45 604,60 906,90 700 DH 1778,0 140 200 10,89 240,65 320,86 481,29 641,73 962,59 750 DH 1905,0 150 200 11,66 257,66 343,55 515,33 687,10 1030,65 800 DH 2032,0 160 200 12,44 274,90 366,53 549,80 733,06 1099,60 850 DH 2159,0 170 200 13,22 292,14 389,51 584,27 779,03 1168,54 900 DH 2286,0 180 200 14,00 309,37 412,50 618,74 824,99 1237,49

CINGHIE E MANICOTTI DOPPIA DENTATURA DOUBLE SIDE TIMING BELTS & SLEEVES POWER SINC DD PROFILO H DOPPIA DENTATURA - PROFILE H DOUBLE SIDE Lp. (mm) (mm) L.Manic. Sleeve Width /Sleeve L=19,05mm Cod / Code 75 L=25,4mm Cod / Code 100 L=38,1mm Cod / Code 150 L=50,8mm Cod / Code 200 L=76,2mm Cod / Code 300 1000 DH 2540,0 200 200 15,55 343,62 458,17 687,25 916,33 1374,50 1100 DH 2794,0 220 200 17,11 378,10 504,13 756,19 1008,26 1512,39 1150 DH 2921,0 230 200 17,89 363,92 527,05 790,56 1054,09 1581,14 1250 DH 3175,0 250 200 19,44 429,59 572,78 859,17 1145,56 1718,34 1400 DH 3556,0 280 200 21,77 481,07 641,43 962,15 1282,86 1924,29 1700 DH 4318,0 340 200 26,44 584,27 779,03 1168,54 1558,06 2337,08 PROFILO 8M DOPPIA DENTATURA - PROFILE 8M DOUBLE SIDE Lp. (mm) (mm) L.Manic. Sleeve Width /Sleeve L=20mm Cod / Code 20 L=30mm Cod / Code 30 L=50mm Cod / Code 50 L=85mm Cod / Code 85 560 8MDD 560 70 180 5,86 135,95 203,93 339,88 577,80 600 8MDD 600 75 180 6,28 145,70 218,54 364,24 619,21 640 8MDD 640 80 180 6,70 155,44 233,16 388,60 660,62 720 8MDD 720 90 180 7,54 174,93 262,39 437,32 743,44 800 8MDD 800 100 180 8,37 194,18 291,28 485,46 825,28 880 8MDD 880 110 180 9,21 213,67 320,51 534,18 908,11 960 8MDD 960 120 180 10,05 233,16 349,74 582,90 990,93 1040 8MDD 1040 130 180 10,89 252,65 378,97 631,62 1073,75 1120 8MDD 1120 140 180 11,72 271,90 407,86 679,76 1155,59 1200 8MDD 1200 150 180 12,56 291,39 437,09 728,48 1238,42 1280 8MDD 1280 160 180 13,40 310,88 466,32 777,20 1321,24 1360 8MDD 1360 170 180 14,24 330,37 495,55 825,92 1404,06 1440 8MDD 1440 180 180 14,40 334,08 501,12 835,20 1419,84 1600 8MDD 1600 200 180 14,57 338,02 507,04 845,06 1436,60 1760 8MDD 1760 220 180 16,03 371,90 557,84 929,74 1580,56 1800 8MDD 1800 225 180 16,39 380,25 570,37 950,62 1616,05 2000 8MDD 2000 250 180 18,21 422,47 633,71 1056,18 1795,51 2400 8MDD 2400 300 180 21,85 506,92 760,38 1267,30 2154,41 2600 8MDD 2600 325 180 23,67 549,14 823,72 1372,86 2333,86 2800 8MDD 2800 350 180 25,49 591,37 887,05 1478,42 2513,31 67 CINGHIE E MANICOTTI DD - DOUBLE SIDE TIMING BELTS & SLEEVES POWER SINC DD

CINGHIE E MANICOTTI DOPPIA DENTATURA DOUBLE SIDE TIMING BELTS & SLEEVES POWER SINC DD PROFILO 14M DOPPIA DENTATURA - PROFILE 14M DOUBLE SIDE Lp. (mm) (mm) L.Manic. Sleeve Width /Sleeve L=40mm Cod / Code 40 L=55mm Cod / Code 55 L=85mm Cod / Code 85 1610 14MDD 1610 115 180 21,44 994,82 1367,87 2113,98 1778 14MDD 1778 127 180 23,68 1098,75 1510,78 2334,85 1890 14MDD 1890 135 180 25,17 1167,89 1605,85 2481,76 2100 14MDD 2100 150 180 27,97 1297,81 1784,49 2757,84 2310 14MDD 2310 165 180 30,77 1427,73 1963,13 3033,92 2450 14MDD 2450 175 180 32,63 1514,03 2081,79 3217,32 2590 14MDD 2590 185 180 34,50 1600,80 2201,10 3401,70 2800 14MDD 2800 200 180 37,29 1730,26 2379,10 3676,79 3150 14MDD 3150 225 180 38,65 1793,36 2465,87 3810,89 3500 14MDD 3500 250 180 42,94 1992,42 2739,57 4233,88 4578 14MDD 4578 327 180 56,17 2606,29 3583,65 5538,36 5740 14MDD 5740 410 180 70,42 3267,49 4492,80 6943,41 68 CINGHIE E MANICOTTI DD - DOUBLE SIDE TIMING BELTS & SLEEVES POWER SINC DD

CINGHIE E MANICOTTI IN POLIURETANO 69 CINGHIE E MANICOTTI IN POLIURETANO

POLYURETHANE TIMING BELTS & SLEEVES 70 POLYURETHANE TIMING BELTS & SLEEVES

CINGHIE DENTATE IN POLIURETANO POLYURETHANE TIMING BELTS Profilo Profile CINGHIE IN POLIURETANO A METRAGGIO - OPEN END POLYURETHANE BELTS L=6mm /Metro L=8mm /Metro L=10mm /Metro L=12mm /Metro L=16mm /Metro L=20mm /Metro L=25mm /Metro L=32mm /Metro L=50mm /Metro L=75mm /Metro T 5 14,09 18,79 23,49 28,19 37,58 46,98 58,72 75,17 117,45 176,18 T 10 22,04 26,45 35,26 44,08 55,10 70,53 110,20 165,30 T 20 138,32 177,05 276,64 Profilo Profile CINGHIE IN POLIURETANO A METRAGGIO - OPEN END POLYURETHANE BELTS L=6mm /Metro L=10mm /Metro L=12mm /Metro L=16mm /Metro L=20mm /Metro L=25mm /Metro L=32mm /Metro L=50mm /Metro L=75mm /Metro AT 5 14,04 23,41 28,09 37,45 58,52 74,90 117,04 175,55 AT 10 25,46 40,73 50,92 63,64 81,47 127,29 190,93 AT 20 150,85 193,09 301,70 CINGHIE IN POLIURETANO A METRAGGIO - OPEN END POLYURETHANE BELTS Profilo Profile L=9,35mm Cod. 037 /Metro L=12,7mm Cod. 050 /Metro L=19mm Cod. 075 /Metro L=25,4mm Cod. 100 /Metro L=38,1mm Cod. 150 /Metro L=50,8mm Cod. 200 /Metro L=76,2mm Cod. 300 /Metro L 19,00 25,81 38,61 51,61 77,42 102,42 154,84 H 26,91 40,26 53,82 80,74 106,80 161,47 XH - - - - - - 71 CINGHIE IN POLIURETANO A METRAGGIO - OPEN END POLYURETHANE BELTS Profilo Profile 5M 21,52 32,28 43,04 53,81 64,57 107,61 8M 25,46 38,19 50,92 76,37 127,29 216,39 14M 136,61 218,58 300,54 Profilo Profile L=10mm /Metro L=15mm /Metro L=20mm /Metro L=25mm /Metro L=30mm /Metro L=40mm /Metro Prezzi per rotoli da 50 mt. - Spezzoni in multipli di 10 mt. supplemento taglio + 10% Price for roll 50 mt. - Lenght mini and multi of 10 mt. + 10% * Con copertura PAZ verde sul dente - * With PAZ on teeth L=50mm /Metro L=55mm /Metro L=85mm /Metro CINGHIE IN POLIURETANO A METRAGGIO - OPEN END POLYURETHANE BELTS L=10mm /Metro L=15mm /Metro L=20mm /Metro L=25mm /Metro L=30mm /Metro L=40mm /Metro L=50mm /Metro L=55mm /Metro L=85mm /Metro RPP 8M* 33,35 50,02 66,70 100,05 166,75 283,48 RPP 14M* 157,48 251,97 346,46 CINGHIE DENTATE IN POLIURETANO - POLYURETHANE TIMING BELTS

CINGHIE E MANICOTTI DENTATI IN POLIURETANO POLYURETHANE TIMING BELTS & SLEEVES PROFILO T2.5 - PROFILE T2.5 L.Manicicotto Sleeve Width /Sleeve L=6mm L=8mm L=10mm L=12mm CINGHIE DENTATE IN POLIURETANO - POLYURETHANE TIMING BELTS 72 T2.5-120 48 150 1,24 8,93 11,90 14,88 17,86 T2.5-145 58 150 1,50 10,80 14,40 18,00 21,60 T2.5-160 64 150 1,66 11,95 15,94 19,92 23,90 T2.5-177,5 71 150 1,84 13,25 17,66 22,08 26,50 T2.5-182,5 73 150 1,89 13,61 18,14 22,68 27,22 T2.5-200 80 150 2,07 14,90 19,87 24,84 29,81 T2.5-230 92 150 2,10 15,12 20,16 25,20 30,24 T2.5-245 98 150 2,14 15,41 20,54 25,68 30,82 T2.5-265 106 150 2,19 15,77 21,02 26,28 31,54 T2.5-285 114 150 2,35 16,92 22,56 28,20 33,84 T2.5-290 116 150 2,39 17,21 22,94 28,68 34,42 T2.5-305 122 150 2,52 18,14 24,19 30,24 36,29 T2.5-317,5 127 150 2,62 18,86 25,15 31,44 37,73 T2.5-330 132 150 2,72 19,58 26,11 32,64 39,17 T2.5-342,5 137 150 2,83 20,38 27,17 33,96 40,75 T2.5-380 152 150 3,14 22,61 30,14 37,68 45,22 T2.5-420 168 150 3,47 24,98 33,31 41,64 49,97 T2.5-480 192 150 3,63 26,14 34,85 43,56 52,27 T2.5-500 200 150 3,65 26,28 35,04 43,80 52,56 T2.5-600 240 150 3,74 26,93 35,90 44,88 53,86 T2.5-620 248 150 3,87 27,86 37,15 46,44 55,73 T2.5-650 260 150 4,06 29,23 38,98 48,72 58,46 T2.5-680 272 150 4,24 30,53 40,70 50,88 61,06 T2.5-700 280 150 4,37 31,46 41,95 52,44 62,93 T2.5-780 312 150 4,87 35,06 46,75 58,44 70,13 T2.5-880 352 150 4,98 35,86 47,81 59,76 71,71 T2.5-915 366 150 5,18 37,30 49,73 62,16 74,59 T2.5-950 380 150 5,38 38,74 51,65 64,56 77,47 T2.5-1185 474 150 6,71 48,31 64,42 80,52 96,62 NEW L.Manicicotto Sleeve Width PROFILO T5 - PROFILE T5 /Sleeve L=10mm L=16mm L=20mm L=25mm T5-120 24 240 1,13 13,56 21,70 27,12 33,90 T5-150 30 240 1,41 16,92 27,07 33,84 42,30 T5-165 33 240 1,74 20,88 33,41 41,76 52,20 T5-180 36 300 1,74 20,88 33,41 41,76 52,20 T5-185 37 300 1,74 20,88 33,41 41,76 52,20

CINGHIE E MANICOTTI DENTATI IN POLIURETANO POLYURETHANE TIMING BELTS & SLEEVES PROFILO T5 - PROFILE T5 L.Manicicotto Sleeve Width /Sleeve L=10mm L=16mm L=20mm L=25mm T5-200 40 300 1,77 21,24 33,98 42,48 53,10 T5-210 42 300 1,77 21,24 33,98 42,48 53,10 T5-215 43 300 1,77 21,24 33,98 42,48 53,10 T5-220 44 300 1,77 21,24 33,98 42,48 53,10 T5-225 45 300 1,80 21,60 34,56 43,20 54,00 T5-245 49 300 1,80 21,60 34,56 43,20 54,00 T5-250 50 300 1,82 21,84 34,94 43,68 54,60 T5-255 51 300 1,82 21,84 34,94 43,68 54,60 T5-260 52 300 1,82 21,84 34,94 43,68 54,60 T5-270 54 300 1,83 21,96 35,14 43,92 54,90 T5-275 55 300 1,83 21,96 35,14 43,92 54,90 T5-280 56 300 1,83 21,96 35,14 43,92 54,90 T5-295 59 300 1,88 22,56 36,10 45,12 56,40 T5-300 60 300 1,91 22,92 36,67 45,84 57,30 T5-305 61 300 1,91 22,92 36,67 45,84 57,30 misura in T5-325 esaurimento 65 300 1,93 23,16 37,06 46,32 57,90 T5-330 66 300 1,93 23,16 37,06 46,32 57,90 T5-340 68 300 1,96 23,52 37,63 47,04 58,80 T5-350 70 300 1,99 23,88 38,21 47,76 59,70 T5-355 71 300 2,01 24,12 38,59 48,24 60,30 T5-365 73 300 2,02 24,24 38,78 48,48 60,60 T5-375 75 300 2,02 24,24 38,78 48,48 60,60 T5-390 78 300 2,02 24,24 38,78 48,48 60,60 T5-400 80 300 2,07 24,84 39,74 49,68 62,10 T5-410 82 300 2,11 25,32 40,51 50,64 63,30 T5-420 84 300 2,12 25,44 40,70 50,88 63,60 T5-425 85 300 2,14 25,68 41,09 51,36 64,20 T5-440 88 300 2,15 25,80 41,28 51,60 64,50 T5-445 89 300 2,16 25,92 41,47 51,84 64,80 T5-450 90 300 2,16 25,92 41,47 51,84 64,80 T5-455 91 300 2,16 25,92 41,47 51,84 64,80 T5-460 92 300 2,16 25,92 41,47 51,84 64,80 T5-475 95 300 2,19 26,28 42,05 52,56 65,70 T5-480 96 300 2,20 26,40 42,24 52,80 66,00 T5-500 100 300 2,25 27,00 43,20 54,00 67,50 T5-510 102 300 2,31 27,72 44,35 55,44 69,30 T5-515 103 300 2,31 27,72 44,35 55,44 69,30 T5-525 105 300 2,33 27,96 44,74 55,92 69,90 T5-545 109 300 2,39 28,68 45,89 57,36 71,70 73 CINGHIE DENTATE IN POLIURETANO - POLYURETHANE TIMING BELTS

CINGHIE E MANICOTTI DENTATI IN POLIURETANO POLYURETHANE TIMING BELTS & SLEEVES PROFILO T5 - PROFILE T5 CINGHIE DENTATE IN POLIURETANO - POLYURETHANE TIMING BELTS 74 L.Manicicotto Sleeve Width /Sleeve L=10mm L=16mm L=20mm L=25mm T5-550 110 300 2,39 28,68 45,89 57,36 71,70 T5-560 112 300 2,48 29,76 47,62 59,52 74,40 T5-575 115 300 2,53 30,36 48,58 60,72 75,90 T5-590 118 300 2,59 31,08 49,73 62,16 77,70 T5-600 120 300 2,68 32,16 51,46 64,32 80,40 T5-610 122 300 2,68 32,16 51,46 64,32 80,40 T5-620 124 300 2,76 33,12 52,99 66,24 82,80 misura in T5-625 esaurimento 125 300 2,78 33,36 53,38 66,72 83,40 T5-630 126 300 2,80 33,60 53,76 67,20 84,00 T5-640 128 300 2,83 33,96 54,34 67,92 84,90 T5-650 130 300 2,87 34,44 55,10 68,88 86,10 T5-660 132 300 2,95 35,40 56,64 70,80 88,50 T5-675 135 300 2,95 35,40 56,64 70,80 88,50 T5-690 138 300 2,96 35,52 56,83 71,04 88,80 T5-700 140 300 2,96 35,52 56,83 71,04 88,80 T5-720 144 300 2,98 35,76 57,22 71,52 89,40 T5-725 145 300 2,98 35,76 57,22 71,52 89,40 T5-750 150 300 2,99 35,88 57,41 71,76 89,70 T5-765 153 300 3,03 36,36 58,18 72,72 90,90 T5-780 156 300 3,03 36,36 58,18 72,72 90,90 T5-800 160 300 3,05 36,60 58,56 73,20 91,50 T5-815 163 300 3,06 36,72 58,75 73,44 91,80 T5-830 166 300 3,07 36,84 58,94 73,68 92,10 T5-840 168 300 3,09 37,08 59,33 74,16 92,70 T5-850 170 300 3,09 37,08 59,33 74,16 92,70 T5-860 172 300 3,09 37,08 59,33 74,16 92,70 T5-885 177 300 3,19 38,28 61,25 76,56 95,70 T5-900 180 300 3,22 38,64 61,82 77,28 96,60 T5-920 184 300 3,37 40,44 64,70 80,88 101,10 T5-940 188 300 3,37 40,44 64,70 80,88 101,10 T5-990 198 300 3,55 42,60 68,16 85,20 106,50 misura in T5-1000 esaurimento 200 300 3,58 42,96 68,74 85,92 107,40 T5-1075 215 300 3,85 46,20 73,92 92,40 115,50 T5-1100 220 300 3,94 47,28 75,65 94,56 118,20 misura in T5-1140 esaurimento 228 300 4,25 51,00 81,60 102,00 127,50 T5-1160 232 300 4,32 51,84 82,94 103,68 129,60 T5-1200 240 300 4,63 55,56 88,90 111,12 138,90 T5-1215 243 300 4,63 55,56 88,90 111,12 138,90 T5-1275 255 300 4,76 57,12 91,39 114,24 142,80

CINGHIE E MANICOTTI DENTATI IN POLIURETANO POLYURETHANE TIMING BELTS & SLEEVES T5-1280 256 300 4,76 57,12 91,39 114,24 142,80 T5-1315 263 300 4,76 57,12 91,39 114,24 142,80 misura in T5-1350 270 300 5,23 62,76 100,42 125,52 156,90 esaurimento L.Manicicotto Sleeve Width PROFILO T5 - PROFILE T5 /Sleeve L=10mm L=16mm L=20mm L=25mm T5-1355 271 300 5,25 63,00 100,80 126,00 157,50 T5-1380 276 300 5,25 63,00 100,80 126,00 157,50 T5-1440 288 300 6,33 75,96 121,54 151,92 189,90 T5-1470 294 300 6,33 75,96 121,54 151,92 189,90 T5-1500 300 300 6,46 77,52 124,03 155,04 193,80 T5-1580 316 300 6,64 79,68 127,49 159,36 199,20 NEW L.Manicicotto Sleeve Width PROFILO T10 - PROFILE T10 /Sleeve L=16mm L=25mm L=32mm L=50mm T10-260 26 300 2,39 45,89 71,70 91,78 143,40 T10-320 32 300 2,42 46,46 72,60 92,93 145,20 T10-340 34 300 2,42 46,46 72,60 92,93 145,20 T10-370 37 300 2,42 46,46 72,60 92,93 145,20 T10-390 39 300 2,42 46,46 72,60 92,93 145,20 T10-400 40 300 2,47 47,42 74,10 94,85 148,20 T10-410 41 300 2,48 47,62 74,40 95,23 148,80 T10-440 44 300 2,52 48,38 75,60 96,77 151,20 T10-450 45 300 2,58 49,54 77,40 99,07 154,80 T10-480 48 300 2,69 51,65 80,70 103,30 161,40 T10-500 50 300 2,69 51,65 80,70 103,30 161,40 T10-530 53 300 2,82 54,14 84,60 108,29 169,20 T10-550 55 300 2,87 55,10 86,10 110,21 172,20 T10-560 56 300 2,92 56,06 87,60 112,13 175,20 T10-600 60 300 2,98 57,22 89,40 114,43 178,80 T10-610 61 300 2,99 57,41 89,70 114,82 179,40 T10-630 63 300 3,01 57,79 90,30 115,58 180,60 T10-650 65 300 3,02 57,98 90,60 115,97 181,20 T10-660 66 300 3,03 58,18 90,90 116,35 181,80 T10-680 68 300 3,07 58,94 92,10 117,89 184,20 T10-690 69 300 3,12 59,90 93,60 119,81 187,20 T10-700 70 300 3,12 59,90 93,60 119,81 187,20 T10-720 72 300 3,14 60,29 94,20 120,58 188,40 T10-730 73 300 3,17 60,86 95,10 121,73 190,20 T10-750 75 300 3,23 62,02 96,90 124,03 193,80 75 CINGHIE DENTATE IN POLIURETANO - POLYURETHANE TIMING BELTS

CINGHIE E MANICOTTI DENTATI IN POLIURETANO POLYURETHANE TIMING BELTS & SLEEVES PROFILO T10 - PROFILE T10 L.Manicicotto Sleeve Width /Sleeve L=16mm L=25mm L=32mm L=50mm CINGHIE DENTATE IN POLIURETANO - POLYURETHANE TIMING BELTS 76 T10-780 78 300 3,26 62,59 97,80 125,18 195,60 T10-800 80 300 3,35 64,32 100,50 128,64 201,00 T10-810 81 300 3,35 64,32 100,50 128,64 201,00 T10-840 84 300 3,63 69,70 108,90 139,39 217,80 T10-850 85 300 3,96 76,03 118,80 152,06 237,60 T10-880 88 300 3,96 76,03 118,80 152,06 237,60 T10-890 89 300 4,04 77,57 121,20 155,14 242,40 T10-900 90 300 4,15 79,68 124,50 159,36 249,00 T10-910 91 300 4,18 80,26 125,40 160,51 250,80 T10-920 92 300 4,21 80,83 126,30 161,66 252,60 T10-950 95 300 4,33 83,14 129,90 166,27 259,80 T10-960 96 300 4,34 83,33 130,20 166,66 260,40 T10-970 97 300 4,35 83,52 130,50 167,04 261,00 T10-980 98 300 4,66 89,47 139,80 178,94 279,60 T10-1000 100 300 4,81 92,35 144,30 184,70 288,60 T10-1010 101 300 4,81 92,35 144,30 184,70 288,60 T10-1050 105 300 4,86 93,31 145,80 186,62 291,60 T10-1080 108 300 4,86 93,31 145,80 186,62 291,60 T10-1100 110 300 4,91 94,27 147,30 188,54 294,60 T10-1110 111 300 4,91 94,27 147,30 188,54 294,60 T10-1140 114 300 4,99 95,81 149,70 191,62 299,40 T10-1150 115 300 5,01 96,19 150,30 192,38 300,60 T10-1200 120 300 5,13 98,50 153,90 196,99 307,80 T10-1210 121 300 5,18 99,46 155,40 198,91 310,80 T10-1240 124 300 5,41 103,87 162,30 207,74 324,60 T10-1250 125 300 5,46 104,83 163,80 209,66 327,60 T10-1300 130 300 5,87 112,70 176,10 225,41 352,20 T10-1320 132 300 6,11 117,31 183,30 234,62 366,60 T10-1350 135 300 6,24 119,81 187,20 239,62 374,40 T10-1390 139 300 6,25 120,00 187,50 240,00 375,00 T10-1400 140 300 6,26 120,19 187,80 240,38 375,60 T10-1420 142 300 6,29 120,77 188,70 241,54 377,40 T10-1440 144 300 6,29 120,77 188,70 241,54 377,40 T10-1450 145 300 6,30 120,96 189,00 241,92 378,00 T10-1460 146 300 6,30 120,96 189,00 241,92 378,00 T10-1500 150 300 6,33 121,54 189,90 243,07 379,80 T10-1560 156 300 6,44 123,65 193,20 247,30 386,40 T10-1600 160 300 6,99 134,21 209,70 268,42 419,40 T10-1610 161 300 7,00 134,40 210,00 268,80 420,00

CINGHIE E MANICOTTI DENTATI IN POLIURETANO POLYURETHANE TIMING BELTS & SLEEVES PROFILO T10 - PROFILE T10 L.Manicicotto Sleeve Width /Sleeve L=16mm L=25mm L=32mm L=50mm T10-1700 170 300 7,53 144,58 225,90 289,15 451,80 T10-1750 175 300 7,77 149,18 233,10 298,37 466,20 T10-1780 178 300 8,04 154,37 241,20 308,74 482,40 T10-1880 188 300 8,25 158,40 247,50 316,80 495,00 T10-1960 196 300 9,32 178,94 279,60 357,89 559,20 T10-2250 225 300 10,72 205,82 321,60 411,65 643,20 NEW L.Manicicotto Sleeve Width PROFILO AT5 - PROFILE AT5 /Sleeve L=10mm L=16mm L=20mm L=25mm AT5-225 45 300 2,15 25,80 41,28 51,60 64,50 AT5-255 51 300 2,19 26,28 42,05 52,56 65,70 AT5-275 55 300 2,20 26,40 42,24 52,80 66,00 AT5-280 56 300 2,20 26,40 42,24 52,80 66,00 AT5-300 60 300 2,22 26,64 42,62 53,28 66,60 AT5-330 66 300 2,22 26,64 42,62 53,28 66,60 AT5-340 68 300 2,35 28,20 45,12 56,40 70,50 AT5-375 75 300 2,39 28,68 45,89 57,36 71,70 AT5-390 78 300 2,43 29,16 46,66 58,32 72,90 AT5-420 84 300 2,55 30,60 48,96 61,20 76,50 AT5-450 90 300 2,59 31,08 49,73 62,16 77,70 AT5-455 91 300 2,61 31,32 50,11 62,64 78,30 AT5-480 96 300 2,68 32,16 51,46 64,32 80,40 AT5-500 100 300 2,68 32,16 51,46 64,32 80,40 AT5-525 105 300 2,85 34,20 54,72 68,40 85,50 AT5-545 109 300 2,85 34,20 54,72 68,40 85,50 AT5-600 120 300 3,12 37,44 59,90 74,88 93,60 AT5-610 122 300 3,21 38,52 61,63 77,04 96,30 AT5-620 124 300 3,21 38,52 61,63 77,04 96,30 AT5-630 126 300 3,25 39,00 62,40 78,00 97,50 AT5-660 132 300 3,36 40,32 64,51 80,64 100,80 AT5-670 134 300 3,39 40,68 65,09 81,36 101,70 AT5-710 142 300 3,49 41,88 67,01 83,76 104,70 AT5-720 144 300 3,53 42,36 67,78 84,72 105,90 AT5-750 150 300 3,60 43,20 69,12 86,40 108,00 AT5-780 156 300 3,63 43,56 69,70 87,12 108,90 AT5-825 165 300 3,69 44,28 70,85 88,56 110,70 AT5-860 172 300 3,75 45,00 72,00 90,00 112,50 77 CINGHIE DENTATE IN POLIURETANO - POLYURETHANE TIMING BELTS

CINGHIE E MANICOTTI DENTATI IN POLIURETANO POLYURETHANE TIMING BELTS & SLEEVES L.Manicicotto Sleeve Width PROFILO AT5 - PROFILE AT5 /Sleeve L=10mm L=16mm L=20mm L=25mm AT5-975 195 300 4,26 51,12 81,79 102,24 127,80 AT5-1050 210 300 4,64 55,68 89,09 111,36 139,20 AT5-1125 225 300 4,74 56,88 91,01 113,76 142,20 AT5-1500 300 300 5,99 71,88 115,01 143,76 179,70 AT5-2000 400 300 7,99 95,88 153,41 191,76 239,70 CINGHIE DENTATE IN POLIURETANO - POLYURETHANE TIMING BELTS 78 NEW PROFILO AT10 - PROFILE AT10 L.Manicicotto Sleeve Width /Sleeve L=16mm L=25mm L=32mm L=50mm AT10-370 37 300 3,06 58,75 91,80 117,50 183,60 AT10-500 50 300 3,22 61,82 96,60 123,65 193,20 misura in AT10-530 esaurimento 53 300 3,49 67,01 104,70 134,02 209,40 AT10-560 56 300 3,53 67,78 105,90 135,55 211,80 AT10-580 58 300 3,56 68,35 106,80 136,70 213,60 AT10-600 60 300 3,60 69,12 108,00 138,24 216,00 AT10-610 61 300 3,61 69,31 108,30 138,62 216,60 AT10-630 63 300 3,63 69,70 108,90 139,39 217,80 AT10-660 66 300 3,72 71,42 111,60 142,85 223,20 AT10-700 70 300 3,86 74,11 115,80 148,22 231,60 AT10-730 73 300 3,93 75,46 117,90 150,91 235,80 AT10-780 78 300 4,03 77,38 120,90 154,75 241,80 AT10-800 80 300 4,35 83,52 130,50 167,04 261,00 AT10-810 81 300 4,35 83,52 130,50 167,04 261,00 AT10-840 84 300 4,35 83,52 130,50 167,04 261,00 AT10-880 88 300 4,83 92,74 144,90 185,47 289,80 AT10-890 89 300 5,04 96,77 151,20 193,54 302,40 AT10-920 92 300 5,20 99,84 156,00 199,68 312,00 AT10-960 96 300 5,58 107,14 167,40 214,27 334,80 AT10-980 98 300 5,64 108,29 169,20 216,58 338,40 AT10-1000 100 300 5,75 110,40 172,50 220,80 345,00 AT10-1010 101 300 5,78 110,98 173,40 221,95 346,80 AT10-1050 105 300 5,84 112,13 175,20 224,26 350,40 AT10-1080 108 300 6,01 115,39 180,30 230,78 360,60 AT10-1100 110 300 6,01 115,39 180,30 230,78 360,60 AT10-1150 115 300 6,28 120,58 188,40 241,15 376,80 AT10-1200 120 300 6,28 120,58 188,40 241,15 376,80 AT10-1210 121 300 6,38 122,50 191,40 244,99 382,80 AT10-1220 122 300 6,38 122,50 191,40 244,99 382,80

CINGHIE E MANICOTTI DOPPIA DENTATURA IN POLIURETANO POLYURETHANE DOUBLE SIDE TIMING BELTS & SLEEVES PROFILO AT10 - PROFILE AT10 L.Manicicotto Sleeve Width /Sleeve L=16mm L=25mm L=32mm L=50mm AT10-1230 123 300 6,43 123,46 192,90 246,91 385,80 AT10-1240 124 300 6,49 124,61 194,70 249,22 389,40 AT10-1250 125 300 6,55 125,76 196,50 251,52 393,00 AT10-1280 128 300 6,58 126,34 197,40 252,67 394,80 AT10-1300 130 300 7,05 135,36 211,50 270,72 423,00 AT10-1320 132 300 7,32 140,54 219,60 281,09 439,20 AT10-1350 135 300 7,49 143,81 224,70 287,62 449,40 AT10-1360 136 300 7,56 145,15 226,80 290,30 453,60 AT10-1400 140 300 7,69 147,65 230,70 295,30 461,40 AT10-1420 142 300 7,80 149,76 234,00 299,52 468,00 AT10-1480 148 300 7,89 151,49 236,70 302,98 473,40 AT10-1500 150 300 7,92 152,06 237,60 304,13 475,20 AT10-1600 160 300 8,39 161,09 251,70 322,18 503,40 AT10-1630 163 300 8,68 166,66 260,40 333,31 520,80 AT10-1700 170 300 8,87 170,30 266,10 340,61 532,20 AT10-1720 172 300 9,27 177,98 278,10 355,97 556,20 AT10-1800 180 300 9,74 187,01 292,20 374,02 584,40 AT10-1860 186 300 9,91 190,27 297,30 380,54 594,60 AT10-1940 194 300 11,18 214,66 335,40 429,31 670,80 79 NEW L.Manicicotto Sleeve Width PROFILO DT5 - PROFILE DT5 /Sleeve L=10mm L=16mm L=20mm L=25mm misura in DT5-300 esaurimento 60 300 1,86 22,32 35,71 44,64 55,80 misura in DT5-350 esaurimento 70 300 2,17 26,04 41,66 52,08 65,10 DT5-410 82 300 2,53 30,36 48,58 60,72 75,90 DT5-460 92 300 2,62 31,44 50,30 62,88 78,60 DT5-515 103 300 3,22 38,64 61,82 77,28 96,60 DT5-525 105 300 3,22 38,64 61,82 77,28 96,60 DT5-550 110 300 3,22 38,64 61,82 77,28 96,60 DT5-590 118 300 3,21 38,52 61,63 77,04 96,30 DT5-620 124 300 3,31 39,72 63,55 79,44 99,30 misura in DT5-650 esaurimento 130 300 3,41 40,92 65,47 81,84 102,30 DT5-685 137 300 3,52 42,24 67,58 84,48 105,60 DT5-700 140 300 3,59 43,08 68,93 86,16 107,70 DT5-750 150 300 3,59 43,08 68,93 86,16 107,70 DT5-815 163 300 3,67 44,04 70,46 88,08 110,10 DT5-840 168 300 3,82 45,84 73,34 91,68 114,60 CINGHIE DENTATE IN POLIURETANO - POLYURETHANE TIMING BELTS

CINGHIE E MANICOTTI DENTATI IN POLIURETANO POLYURETHANE TIMING BELTS & SLEEVES L.Manicicotto Sleeve Width PROFILO DT5 - PROFILE DT5 /Sleeve L=10mm L=16mm L=20mm L=25mm DT5-860 172 300 3,82 45,84 73,34 91,68 114,60 misura in DT5-900 esaurimento 180 300 3,99 47,88 76,61 95,76 119,70 DT5-940 188 300 4,26 51,12 81,79 102,24 127,80 DT5-1100 220 300 4,73 56,76 90,82 113,52 141,90 CINGHIE DENTATE IN POLIURETANO - POLYURETHANE TIMING BELTS 80 NEW PROFILO DT10 - PROFILE DT10 L.Manicicotto Sleeve Width /Sleeve L=16mm L=25mm L=32mm L=50mm DT10-260 26 300 2,86 54,91 85,80 109,82 171,60 DT10-530 53 300 3,39 65,09 101,70 130,18 203,40 DT10-630 63 300 3,61 69,31 108,30 138,62 216,60 DT10-660 66 300 3,63 69,70 108,90 139,39 217,80 DT10-700 70 300 3,80 72,96 114,00 145,92 228,00 DT10-720 72 300 3,80 72,96 114,00 145,92 228,00 DT10-800 80 300 4,35 83,52 130,50 167,04 261,00 DT10-840 84 300 4,35 83,52 130,50 167,04 261,00 DT10-900 90 300 5,59 107,33 167,70 214,66 335,40 DT10-920 92 300 5,59 107,33 167,70 214,66 335,40 DT10-980 98 300 5,59 107,33 167,70 214,66 335,40 DT10-1010 101 300 5,96 114,43 178,80 228,86 357,60 DT10-1100 110 300 5,96 114,43 178,80 228,86 357,60 DT10-1150 115 300 6,21 119,23 186,30 238,46 372,60 DT10-1210 121 300 6,21 119,23 186,30 238,46 372,60 DT10-1240 124 300 6,50 124,80 195,00 249,60 390,00 DT10-1250 125 300 6,55 125,76 196,50 251,52 393,00 DT10-1320 132 300 7,33 140,74 219,90 281,47 439,80 DT10-1350 135 300 7,48 143,62 224,40 287,23 448,80 DT10-1420 142 300 7,54 144,77 226,20 289,54 452,40 misura in DT10-1500 150 300 7,92 152,06 237,60 304,13 475,20 esaurimento DT10-1610 161 300 8,39 161,09 251,70 322,18 503,40 misura in DT10-1800 180 300 9,12 175,10 273,60 350,21 547,20 esaurimento DT10-1880 188 300 9,89 189,89 296,70 379,78 593,40

CINGHIE TERMOSALDABILI TRAPEZ. E TONDE / URETHANE V & ROUND BELTS TIPO / BELT TYPE VMT VMTR VMV VMVR Colore/Colour Chiaro/Clear Chiaro/Clear Verde/Green Verde/Green Durezza/Hardness (shore A) 88 88 87 87 Temp/Temp -30 C+80 C -30 C+80 C -30 C+80 C -30 C+80 C Coeff.di frizione/ of Friction (Steel) 0,41 0,41 0,4 0,4 Superficie/Surface Liscia/Smooth Liscia/Smooth Liscia/Smooth Liscia/Smooth Rinforzo/Reinforcement No Yes No Si/Yes Approvazione FDA/FDA Approved No No No No Forma/shape Sezione / Section MWL MPD MWL MPD MWL MPD MWL MPD A - (13X8) 20 50 40 50 19 48 38 48 B - (17X11,5) 38 75 70 75 36 73 66 73 20 - (20X12,5) 55 90 90 90 52 85 86 85 C - (22X14,5) 64 100 120 100 60 97 110 97 81 TIPO/BELT TYPE VMT-RT VMTR-RT VMV-RT VMVR-RT Colore/Colour Chiaro/Clear Chiaro/Clear Verde/Green Verde/Green Durezza/Hardness (shore A) 88 88 87 87 Temp/Temp -30 C+80 C -30 C+80 C -30 C+80 C -30 C+80 C Coeff.di frizione/ of Friction (Steel) 0,41 0,41 0,4 0,4 Superficie/Surface Crestata/Crested Crestata/Crested Crestata/Crested Crestata/Crested Rinforzo/Reinforcement No Si/Yes No Si/Yes Approvazione FDA/FDA Approved No No No No Forma/shape Sezione / Section MWL MPD MWL MPD MWL MPD MWL MPD B - (17X11,5) 55 130 110 130 52 125 105 125 C - (22X14,5) 85 190 180 190 80 185 170 185 MPD = Minimo diametro Puleggia / Minimum Pulley Diameter (mm) MWL = Massimo carico di lavoro / Max. Work Load in (kg) CINGHIE TERMOSALDABILI TRAPEZ. E TONDE / URETHANE V & ROUND BELTS

CINGHIE TERMOSALDABILI TRAPEZ. E TONDE / URETHANE V & ROUND BELTS TIPO/BELT TYPE VMT VMTR VMV VMVR Colore/Colour Chiaro/Clear Chiaro/Clear Verde/Green Verde/Green Durezza/Hardness (shore A) 88 88 87 87 Temp/Temp -30 C+80 C -30 C+80 C -30 C+80 C -30 C+80 C Coeff.di frizione/ of Friction (Steel) 0,41 0,41 0,4 0,4 Superficie/Surface Liscia/Smooth Liscia/Smooth Liscia/Smooth Liscia/Smooth Rinforzo/Reinforcement No Yes No Yes Approvazione FDA/FDA Approved No No No No Forma/shape Belt Section MWL MPD MWL MPD MWL MPD MWL MPD A - (13X8) 20 50 40 50 19 48 38 48 B - (17X11,5) 38 75 70 75 36 73 66 73 C - (22X14,5) 64 100 120 100 60 97 110 97 CINGHIE TERMOSALDABILI TRAPEZ. E TONDE / URETHANE V & ROUND BELTS 82 TIPO/BELT TYPE RMT RMTR RMV RMVR Colore/Colour Chiaro/Clear Chiaro/Clear Verde/Green Verde/Green Durezza/Hardness (shore A) 88 88 87 87 Temp/Temp -30 C+80 C -30 C+80 C -30 C+80 C -30 C+80 C Coeff.di frizione/ of Friction (Steel) 0,41 0,41 0,40 0,40 Superficie/Surface Liscia/Smooth Liscia/Smooth Ruvida/Rough Ruvida/Rough Rinforzo/Reinforcement No Si/Yes No Si/Yes Approvazione FDA/FDA Approved No No No No Forma/shape Diameter MWL MPD MWL MPD MWL MPD MWL MPD 2 0,85 15 n.a. 0,80 15 n.a. 3 2,00 20 n.a. 1,90 20 n.a. 4 3,50 40 n.a. 3,40 40 n.a. 5 5,35 48 n.a. 5,20 48 n.a. 6 7,70 57 18,00 60 7,50 57 17,00 60 7 11,00 67 n.a. 10,50 67 n.a. 8 14,50 76 30,00 80 14,00 76 29,00 80 9 17,50 86 n.a. 17,00 86 n.a. 10 22,00 95 44,00 100 21,00 95 43,00 100 12 32,00 114 62,00 120 30,00 114 60,00 120 15 49,00 143 100,00 150 47,00 143 96,00 150 18 70,00 171 142,00 67,00 171 138,00 180 20 81,00 190 n.a. 180 76,00 190 n.a. MPD = Minimo diametro Puleggia / Minimum Pulley Diameter (mm) MWL = Massimo carico di lavoro / Max. Work Load in (kg)

CINGHIE TERMOSALDABILI TRAPEZ. E TONDE / URETHANE V & ROUND BELTS Forma Shape Codice della cinghia Belt description RMT 6 Colore Color Finitura Finishing Rinforzo Reinforced sezione Section Shore (A) Ø 6 88 RMT 8 Ø 8 88 RMT 10 Ø 10 88 RMT 12 Trasparente Liscia Ø 12 88 RMTR 8 Transparent Smooth Rinfo. - Reinf. Ø 8 88 RMTR 10 Rinfo. - Reinf. Ø 10 88 RMTR 12 Rinfo. - Reinf. Ø 12 88 RMTR 15 Rinfo. - Reinf. Ø 15 88 Prezzo / prix netto / mt A richiesta / on demand Forma Shape Codice della cinghia Belt description Colore Color Finitura Finishing Rinforzo Reinforced sezione Section Shore (A) RMV 8 Ø 8 87 RMV 10 Ø 10 87 RMV 12 Ø 12 87 Verde Ruvida RMVR 8 Green Rough Rinfo. - Reinf. Ø 8 87 RMVR 10 Rinfo. - Reinf. Ø 10 87 RMVR 12 Rinfo. - Reinf. Ø 12 87 RMVR 15 Rinfo. - Reinf. Ø 15 87 Prezzo / prix netto / mt A richiesta / on demand 83 Forma Shape Codice della cinghia Belt description Colore Color Finitura Finishing Rinforzo Reinforced sezione Section Shore (A) VMT 13A A 13x8 88 VMT 13A SG supergrip A 13x11 88 VMT 17B B 17x11 88 VMT 17B SG supergrip B 17x13 88 VMT 17B RT crestata/crested B 17x16 88 VMT 22C C 22x14 88 VMT 22C RT crestata/crested C 22x19 88 Trasparente VMTR 13A Rinfo. - Reinf. A 13x8 88 Transparent VMTR 13A SG supergrip Rinfo. - Reinf. A 13x10 88 VMTR 17B Rinfo. - Reinf. B 17x11 88 VMTR 17B SG supergrip Rinfo. - Reinf. B 17x13 88 VMTR 17B RT crestata/crested Rinfo. - Reinf. B 17x16 88 VMTR 22C Rinfo. - Reinf. C 22x14 88 VMTR 22C SG supergrip Rinfo. - Reinf. C 22x16 88 VMTR 22C RT crestata/crested Rinfo. - Reinf. C 22x19 88 Prezzo / prix netto / mt A richiesta / on demand CINGHIE TERMOSALDABILI TRAPEZ. E TONDE / URETHANE V & ROUND BELTS

CINGHIE TERMOSALDABILI TRAPEZ. E TONDE / URETHANE V & ROUND BELTS 84 Forma Shape Codice della cinghia Belt description Colore Color Finitura Finishing Rinforzo Reinforced sezione Section Shore (A) VMV 13A A 13x8 87 VMV 13A SG supergrip A 13x11 87 VMV 17B B 17x11 87 VMV 17B SG supergrip B 17x13 87 VMV 17B RT crestata/crested B 17x16 87 VMV 22C C 22x14 87 VMV 22C RT crestata/crested C 22x19 87 Verde - VMVR 13A Rinfo. - Reinf. A 13x8 87 Green VMVR 13A SG supergrip Rinfo. - Reinf. A 13x10 87 VMVR 17B Rinfo. - Reinf. B 17x11 87 VMVR 17B dentel dentellata/cogged Rinfo. - Reinf. B 17x11 87 VMVR 17B SG supergrip Rinfo. - Reinf. B 17x13 87 VMVR 17B RT crestata/crested Rinfo. - Reinf. B 17x16 87 VMVR 22C Rinfo. - Reinf. C 22x14 87 VMVR 22C SG supergrip Rinfo. - Reinf. C 22x16 87 VMVR 22C RT crestata/crested Rinfo. - Reinf. C 22x19 87 Prezzo / prix netto / mt A richiesta / on demand RT = CRESTATA - CRESTED CINGHIE TERMOSALDABILI TRAPEZ. E TONDE / URETHANE V & ROUND BELTS SG = SUPERGRIP - SUPERGRIP R = RINFORZATA - REINFORCED T = TRASPARENTE - TRANSPARENT COLOR V = VERDE - GREEN COLOR

CINGHIE SPECIALI / SPECIAL BELTS Per cinghie giuntate, crestate, rivestite con tenax, PU, nido d ape e altri rivestimenti richiedere quotazione For joined belts, pentagonal, Tenax, PU, Supergrip, and other back cover contact us Crestatura Nido d ape 85 CINGHIE SPECIALI - SPECIAL BELTS

STRUMENTI DI MISURAZIONE E CONTROLLO 20,00 Prezzo netto 780,00 Prezzo netto 86 50,00 Prezzo netto STRUMENTI DI MISURA E CONTROLLO

CONDIZIONI GENERALI DI VENDITA 1. Ordini Gli ordini, sia di materiale standard o speciale, devono essere riferiti al listino o alle offerte scritte della PIZZIRANI S.r.l. e sono da ritenersi validi solo dopo l emissione della relativa conferma d ordine. Gli ordini sono impegnativi per il cliente e non possono essere disdetti salvo accordi particolari,e risarcimento dei costi vivi sostenuti. 2. Prezzi Si intendono quelli in vigore alla data dell ordine e specificati nella Conferma d ordine. Qualora, nel periodo di fornitura si verificassero aumenti dei costi di qualsiasi natura, è facoltà della Soc. PIZZIRANI, previa motivazione dettagliata, adeguare i prezzi sugli ordini in corso. 3. Termini di consegna Sono da considerarsi validi i tempi indicativi menzionati nella conferma d ordine. In caso di avvenimenti imprevisti (scioperi, maltempo, catastrofi naturali, ed altro)non imputabili alla Soc. Pizzirani, i termini di consegna possono venire prorogati senza che la Soc. Pizzirani sia tenuta a corrispondere indennizzi o rimborsi di ogni tipo. Il cliente in ogni caso ha l obbligo di ritirare materiale a disegno o a programma concordato. 4. Spedizioni Il materiale, dove non diversamente specificato, è reso franco ns magazzino, e viaggia a rischio e pericolo del cliente. In caso di spedizione a carico della Soc. Pizzirani, questa si riserva di scegliere il vettore. I reclami per eventuali ammanchi o non corrispondenza delle merci devono essere presentati in forma scritta entro e non oltre 8 giorni dalla data di consegna. Eventuali colli danneggiati devono essere accettati con riserva 5. Imballi In assenza di accordi specifici l imballo è a carico del cliente. Nel caso in cui l imballo sia a carico della Soc. Pizzirani, è facoltà della stessa determinarne la tipologia e le dimensioni. 87 6. Resi Non si accettano resi se non precedentemente autorizzati. L eventuale reso sarà a carico del cliente, e a copertura degli oneri di gestione al cliente verrà emessa nota di addebito pari al 15% del valore reso. 7. Garanzia La Soc. Pizzirani si impegna a sostituire gratuitamente la merce da essa riconosciuta difettosa, previa verifica del ns servizio tecnico. La garanzia decade nel caso in cui il materiale non sia stato montato ed utilizzato secondo le norme e le prescrizioni fornite dalla Soc. Pizzirani. 8. Responsabilità La Soc. Pizzirani non assume responsabilità né riconosce indennizzi di alcun tipo per danni che si dovessero verificare durante l impiego dei suoi prodotti o da essa forniti. 9. Pagamenti Le condizioni di pagamento sono concordate con il cliente ed indicate nella Conferma d Ordine In caso di ritardato pagamento, la Soc. Pizzirani si riserva di sospendere le forniture,ed metterà N.D per interessi di mora al tasso del 3%superiore a quello legale. Qualsiasi contestazione sulla merce non solleva il cliente dall obbligo di onorare i pagamenti in corso alle scadenze pattuite. 10. Proprietà Tutto il materiale rimane di proprietà della Soc. Pizzirani fino al pagamento completo delle fatture relative al materiale stesso. 11. Foro competente Qualsiasi controversia inerente ai rapporti commerciali con la Soc. Pizzirani, sarà di competenza del Tribunale di Siena. CONDIZIONI GENERALI DI VENDITA

GENERAL CONDITIONS OF SALE 1.ORDERS Orders of standard or special products shall be in accordance with the price list of PIZZIRANI (hereinafter called the Seller ) or in terms of the Seller s written quotations; they shall become binding after the Seller has confirmed the order. The Seller s confirmation of order cannot be cancelled unless by special agreement, whereby charges for such cancellation shall be invoiced in terms of any expenses incurred. 2.PRICES The prices of products are indicated in the Seller s price list; Seller s written quotations are applicable when an order confirmation has been issued. In cases of price increases during the supply period, the Seller will promptly inform the purchaser, with detailedexplanations, about the price adjustments. 3.TERMS OF DELIVERY The delivery date is as specified in the order confirmation. In the event of the unexpected (strikes, bad weather conditions, natural catastrophes etc.), delivery may be delayed at no additional charge to the Seller. Custom-made items or prearranged orders must be honored by the Purchaser in any event. 4.CONSIGNMENT OF GOODS Once the products have been dispatched, they will be considered ex-factory and the risk associated with the transport thereof will become the responsibility of the Purchaser. Consignments under the control of the Seller, however, will be transported by Pizzirani partner carriers. Claims for missing or non-standard items must be sent by fax or e-mail within 8 days from the delivery date. Damaged items will be accepted by the Seller, without prejudice, once they have been examined. 88 5.PACKAGING Packaging will be the responsibility of the Purchaser, unless the Purchaser has entrusted this to the Seller, in which case Pizzirani will take all the necessary decisions on the packaging materials and dimensions to be used. 6.RETURNED GOODS Goods can only be returned with the Seller s pre-approval. In such an event, a charge of 15% of the gross value of the goods will be invoiced in order to cover the expenses occurred. 7.WARRANTY The Seller will replace defective items free of charge, upon examination by our technical staff. The warranty is not valid if the items are not installed or used in the manner prescribed by the Seller. 8.RESPONSIBILITY The Seller shall not be held liable for damages or accidents occurring during the use of its products. GENERAL CONDITIONS OF SALE 9.PAYMENT The terms of payment as agreed between the Seller and the Purchaser are stated and become binding in the order confirmation. In the event of delayed payment, the Seller has the right to cease the supply of goods and will invoice a debit note at an interest rate of 3%. 10.PROPERTY All items shall remain the property of the Seller until full payment of the invoices has been realized. 11.ARBITRATION Any dispute or claim concerning commercial relations with the Seller shall be settled by arbitration in the Court of Siena (Italy).