USER MANUAL Barcode Scanner ITA/ ENG
Grazie per aver scelto un nostro prodotto ITITA
Informazioni prodotto Lettore codice a barre USB plug & play in grado di leggere tutti i codici a barre standard 1D quali UPC-A, UPC-E, EAN-13/JAN-13, ISBN/ISSN, EAN-8/JAN-8, code 39, code 32, code 98, code 128, interleaved 2 di 5, industrial 2 di 5, MSI/Plessy e Codebar. Descrizione prodotto 1 Indicatore luminoso 2 Cover resistente agli urti 3 Tasto scansione 4 Foro estrazione cavo
Angolo di lettura - Posizionare la pistola leggermente angolata rispetto al codice da leggere. - L angolo tra codice e pistola non deve essere 90. - Lo scanner deve mirare al codice a barre e il fascio deve coprire l intero codice a barre. modi corretti di scansione modi non corretti di scansione Connessione della scanner Connettere il cavo USB alla porta USB del PC Contenuto della confezione n 1 Lettore codice a barre n 1 Cavo n 1 Manuale utente ITITA
Parametri tecnici Interfaccia USB Velocita 1200-115200 Sorgente Decodifica Modalità Scansione Distanza Risoluzione Profondità Di Campo Velocità Larghezza Fascio Modalità Pronta Contrasto 30% Angolo Scansione Materiale Alimentatore Corrente Operativa Grado IP 54 Laser visibile 650nm ( national laser safety standard class 1 ) code 39, code 93, code 128, ucc/ean-128, ean- 8, ean-13, upc-a, issn+2, isbn+5, industrial 25, code32 etc.. manuale, automatica, continua 15cm(100cm2) minima 0.1mm ( 4mils) 2-9cm ( 0.1mm larghezza ); 3-50cm (0.3mm larghezza) 300 scansioni al secondo 5cm-30cm beep, indicatore led roll 30, pitch 75, yaw 65 cilindro orizontale abs+pc dc5v+-5% 50ma (in modalità operativa); 30ma (in modalità standby); 100ma (consumo massimo) 20ma(a riposo)
Temperatura Operativa Umidita Stoccaggio Protezione Esd Resistenza Agli Urti 0 a 50 c / 32 a 122 f temperatura stoccaggio 20 85% ( in assenza di condensa ) 15kv scariche in aria 1.5m su superfici lisce ITITA
Settaggio funzioni
ITITA
Settaggio Barcode ITITA
ITITA
ITITA
Aggiungi prefisso Primo Step Scannerizzare il codice posto in basso (questo step cancellerà il prefisso precedentemente impostato) Secondo Step Scannerizzare il codice carattere necessario (max 10 caratteri ) Esempio: Per aggiungere il prefisso MG, scannerizzare il carattere M e G in ordine Adesso MG sarà aggiunto quando scannerizzi il normale codice a barre Scannerizzare il codice a barre TEST sopra, il risultato sarà MGTEST ITITA
Aggiungi suffisso Primo Step Scannerizzare il codice posto in basso (questo step cancellerà il suffisso precedentemente impostato) Secondo Step Scannerizzare il codice carattere necessario (max 10 caratteri) Esempio: Per aggiungere il suffisso OK, scannerizzare il carattere O e K in ordine Adesso OK sarà aggiunto quando scannerizzi il normale codice a barre Scannerizzare il codice a barre TEST sopra, il risultato sarà TESTOK
Nascondere Caratteri Iniziali Primo Step Scannerizzare il codice posto in basso (questo step cancellerà il settaggio precedente) Secondo Step Scannerizzare il numero di caratteri da nascondere (max 10 caratteri) Esempio: Per nascondere i primi 2 caratteri, scannerizzare il codice set-up 02 Adesso i due caratteri iniziali saranno nascosti quando scannerizzi il normale codice a barre Scannerizzare il codice a barre TEST sopra, il risultato sarà 3456789 ITITA
Nascondere Caratteri Finali Primo Step Scannerizzare il codice posto in basso (questo step cancellerà il settaggio precedente) Secondo Step Scannerizzare il numero di caratteri da nascondere (max 10 caratteri) Esempio: Per nascondere gli ultimi 3 caratteri, scannerizzare il codice set-up 03 Adesso i tre caratteri finali saranno nascosti quando scannerizzi il normale codice a barre Scannerizzare il codice a barre TEST sopra, il risultato sarà 987654
ITITA
ITITA
ITITA
Thanks for choosing our product ENG
Product information This is a Plug&Play wired laser barcode scanner that can read all the standard 1D bar codes inluding UPC-A, UPC-E, EAN-12/JAN-13, ISBN/ISSN code, EAN-8/JAN8, code 39, code 93, code 128, Interleaved 2 or 5, industrial 2 of 5, Chinese Postal Code, MSI/Plessy and Codabar. Housing design description 1 Indicator light 2 Shock resistance over 3 Trigger button 4 Cable disassembly hole
Reading Angle - Maintain a bevel between the scanner and the barcode to make a best reading. - Do not keep the scanner in 90 with the barcode, otherwise the scanner can t read. - The scanner must aim at the barcode and the beam must cover the whole barcode. If don t, error maybe occur. correct ways of reading incorrect ways of reading Connecting the scanner Connect the USb cable to the USB interface in the computer Packing List n 1 Barcode scanner n 1 Cable n 1 User manual ENG
Technical Parameters Interface USB Baud rate 1200-115200 Light source Decoding capability Trigger mode Sensing distance Resolution Dept of field Decoding speed Scanning width Prompt mode Contrast 30% Visible laser 650nm ( national laser safety standard class 1 ) code 39, code 93, code 128, ucc/ean-128, ean- 8, ean-13, upc-a, issn+2, isbn+5, industrial 25, code32 etc.. manual, auto, continuous 15cm(100cm2) minimum 0.1mm ( 4mils) 2-9cm (0.1mm width); 3-50cm (0.3mm width) 300 scans/sec 5cm-30cm beep, indicator light Scan angle roll 30, pitch 75, yaw 65 Material Power supply Operating current IP grade 54 Operating temperature abs+pc dc5v+-5% 50ma (operation mode); 30ma (standby mode); 100ma (max peak); 20ma (at rest) 0 a 50 c / 32 a 122 f storage temperature
Storage Humidity ESD protection Shock resistance 20 85% (no-condensing) 15kv air discharge 1.5m free on concrete surface ENG
Function setting
ENG
Barcode setting ENG
ENG
ENG
Add prefix The first step Scan the set-up code below (this step will clear the pre-set prefix) The second step Scan the needed character code (max 10 characters ) Example: To ass prefix MG, scan character M ang G orderly Now MG will be added when scanning the normal bar codes Scan the above testing bar code, the MGTEST will show ENG
Add suffix The first step Scan the set-up code below (this step will clear the re-set suffix) The second step Scan the needed character code (max 10 characters) Example: To add suffix OK, scan character O and K orderly Now OK will be added when scanning the normal bar codes Scan the above testing bar code, TESTOK will be shown
Hide the front characters The first step Scan the set-up code below (this step will clear the previous settings) The second step Scan the number needs to be hidden (max 10 characters) Example: To hide two front characters, scan the set-up code 02 Now two front characters will be hidden when scanning the normal bar codes. Scan the above testing bar code, 3456789 will be shown ENG
Hide the behind characters The first step Scan the set-up code below (this step will clear the previous settings) The second step Scan the number needs to be hidden (max 10 characters) Example: To hide three behind characters, scan the set-up code 03 Now three behind characters will be hidden when scanning the normal bar codes Scan the above testing bar code, 987654 will be shown
ENG
ENG
ENG
ENG
Mach Power is a registered trademark All Rights Reserved > visit our web site www.machpower.it