USER MANUAL 2AMIN521VS SUBJECT INDEX: DESCRIPTION TECHNICAL SPECIFICATION FUNCTIONAL DESCRIPTION DEVICE POWER SUPPLY AND CONNECTION TO THE LED MODULE SINGLE POWER SUPPLY MODE MULTIPLE POWER SUPPLY MODE Necto Group S.r.l. 35127 Padova - Via Canada, 8 - ITALY - T +39 049 8791001 F +39 049 8791002 Email info@nectogroup.com pag. 1
AMPLIFICATORE SLAVE PER DIMMER IoT Light SLAVE AMPLIFIER IoT Light USER MANUAL 2AMIN521VS CARATTERISTICHE TECNICHE TECHNICAL NOTES - Dimmer Mono canale con Uscita in Tensione PWM. - Range di alimentazione: 10-53V DC. - Ripetitore di segnale PWM. - Il dispositivo è ideato per rigenerare un ingresso PWM in tensione con uscita fino a 12 A. - Il dispositivo permette di rigenerare il segnale PWM utilizzando anche una tensione di alimentazione differente da quella di ingresso. - Ingressi di Controllo: PWM x1. - Uscite di sincronia: PWM x1. - Circuito Stampato UL. - Classe di protezione: IP20. - Dimensioni Standard 40x80x24.45 mm. - Dimensioni con Accessori 40x100x24.45 mm. - Protezione da picchi tensione. PULSANTE N/O ISOLATO N/O insulated switch - Mono channel Dimmers with Output Tension PWM. - Input Range: 10-53V DC. - PWM repeter. - The device is able to amplifier a PWM voltage input with an output current up to 12 A. - The device allows to regenerate the PWM signal using also different power supply. - Input Controls: PWM x1. - Output Sync: PWM x1. - Printed Circuit UL. - Protection Class: IP20. - Standard Dimension 40x80x24.45 mm. - Dimension with accessories 40x100x24.45 mm. - Surge voltage protection. INGRESSI DI CONTROLLO - CONTROL INPUTS PWM x1 USCITA SYNCRO OUTPUT SYNCRO PWM X1 CORRENTE MAX (*) MAX OUTPUT CURRENT 12A Dimmer Mono canale con Uscita in Tensione PWM. Range di alimentazione: 10-53V DC. Ripetitore di segnale PWM. Il dispositivo è ideato per rigenerare un ingresso PWM in tensione con uscita fino a 12 A. Il dispositivo permette di rigenerare il segnale PWM utilizzando anche una tensione di alimentazione differente da quella di ingresso. Mono channel Dimmers with Output Tension PWM. Input Range: 10-53V DC. PWM repeter. The device is able to amplifier a PWM voltage input with an output current up to 12 A. The device allows to regenerate the PWM signal using also different power supply. Necto Group S.r.l. 35127 Padova - Via Canada, 8 - ITALY - T +39 049 8791001 F +39 049 8791002 Email info@nectogroup.com pag. 2
CODICE CODE TENSIONE IN INGRESSO INPUT VOLTAGE CORRENTE MAX MAX OUTPUT CURRENT n. CANALI n. OUTPUT CHANNELS POTENZA MAX MAX OUTPUT POWER INGRESSI DI CONTROLLO CONTROL INPUTS SCATOLA CASE DIM. DIM. 2AMIN521VS 10-53V DC 12A 1 576W a 48V DC PWM x1 SI 40x80 mm h 24.45 mm Necto Group S.r.l. 35127 Padova - Via Canada, 8 - ITALY - T +39 049 8791001 F +39 049 8791002 Email info@nectogroup.com pag. 3
FUNCTIONAL DESCRIPTION The 2AMIN521VS device comes from the need to extend the current demand for large installation and/or syncronize the dimming of heterogeneous LED modules (in terms of power supply voltage). The 2AMIN521VS device is designed to regenerate a PWM input voltage taken directly across the load. THE 2AMIN521VS DEVICE GUARANTEES MAXIMUM PWM RESOLUTION AND PERFORMANCE WITH LOW CAPACITIVE LOADS (EXAMPLE: CV STRIP LED) THE 2AMIN521VS DEVICE IS COMPATIBLE WITH THE FOLLOWING NECTO GROUP PRODUCTS: 2AMDI511VPVRDS 2AMDI511VPVRDBS 2AMDI516VPVRDXBS 2AMDI523VPVRDXS 2AMDI551VPDBS DEVICE POWER SUPPLY AND CONNECTION TO THE LED MODULE POWER SUPPLY CONNECTION DIAGRAM AND LED 2AMIN521VS - FIGURE N. 1 The 2AMIN521VS dimmer has to be powered according to the polarity showed in FIG. 1 through the DC IN (+ and -) terminals. The LED load connection has to be made by using the OUT (L+ and L-) terminals. The PWM input signal must be connected to the D1 and D2 terminals, regardless of polarity. The LED DIM IN, positioned on the circuit board, indicates the presence of PWM input. The LED DIM OUT, positioned on the circuit board, indicates the presence of PWM output. Necto Group S.r.l. 35127 Padova - Via Canada, 8 - ITALY - T +39 049 8791001 F +39 049 8791002 Email info@nectogroup.com pag. 4
SINGLE POWER SUPPLY MODE PWM WIRING DIAGRAM SINGLE POWER SUPPLY - FIGURE N. 2 MULTIPLE POWER SUPPLY MODE PWM WIRING DIAGRAM MULTIPLE POWER SUPPLY - FIGURE N. 3 Necto Group S.r.l. 35127 Padova - Via Canada, 8 - ITALY - T +39 049 8791001 F +39 049 8791002 Email info@nectogroup.com pag. 5