SRT064 BTH SRT051 BTH SRT052 BTH

Dimensione: px

Iniziare la visualizzazioe della pagina:

Download "SRT064 BTH SRT051 BTH SRT052 BTH"

Aureliano Grassi
6 anni fa
Visualizzazioni

1 KIT FOR TRUCK BRAKE TESTERS SRT051 BTH SRT052 BTH OPERATOR S MANUAL SRT064BTH SRT051BTH SRT052BTH

2 CONTENTS 1. INTRODUCTION Description of SRT064BTH Kit Description of SRT051BTH Kit Description of SRT052 BTH Kit Positioning the SRT064BTH Kit Positioning the SRT051BTH Kit Positioning the SRT052BTH Kit CONFIGURATION...5

3 1. INTRODUCTION This manual provides detailed instructions for the customer, for the purpose of connecting the pedal pressure measuring devices on RAVAGLIOLI truck or double speed brake testers. device functionality is ensured on brake tester systems with FW versions 1.63 or later (the FW version can be read on the first page of the program at lower right and should be available from April 2006, see example in Figure 1). FW version 1.63 Figure 1 IMPORTANT: A number of program parameters need only be changed during first installation of devices. This operation must only be performed by the RAVAGLIOLI S.p.A. skilled technical assistance personnel; for this reason access requires a password. If these parameters are not changed, even if all the following instructions are followed, the device will not work. The measuring devices besides providing excellent transmission, also make it possible to have several units interact in the same environment. The transmitter comes on by pressing the ON key, the red LED comes on. After a few seconds, the transmitter connects with the receiver and this condition is shown by the flashing red LED. To switch off press the OFF key. Switch-off occurs after about 2 sec.; the red LED goes off. Green LED ON key Red LED OFF key When not used, the transmitter goes off automatically, after it has not been connected for a few minutes (e.g., because the console is off) or after a few minutes when no pressure is applied to the cell. When the transmitter is put under charge, the green LED comes on; to ensure charge is correct, the transmitter must be off (red LED off). Page 1/6

2. Description of SRT064BTH Kit 2 1 Figure 2 3 1) Pedal pressure with transmitter 2) Battery charter for transmitter 3) receiver with wiring harness 3.

4 2. Description of SRT064BTH Kit 2 1 Figure 2 3 1) Pedal pressure with transmitter 2) Battery charter for transmitter 3) receiver with wiring harness 3. Description of SRT051BTH Kit Figure 3 1) P1 Air pressure transducer with transmitter 2) Battery charter for transmitter 3) receiver with wiring harness 4) Additional serial board 3 4. Description of SRT052 BTH Kit Figure 4 3 1) P2 Air pressure transducer with transmitter 2) Battery charter for transmitter 3) receiver with wiring harness 4) 9-pole Tray adapter Ampmodu 4-pole In a truck or double speed brake tester system, one, two or all the above devices can be fitted. Only the installation of measuring device P2 is conditioned by the installation of P1. Page 2/6

position the receiver in the inside part using adhesive supports RAVRT011TF11/15/TFV RAVRT009TF11/15 position the receiver in the inside part using adhesive supports Figure 5 The wiring harness must

5 5. Positioning the SRT064BTH Kit Do not position the receiver directly on metal surfaces. In the case of the console units, remove the position this as shown below, in the inside part, using adhesive supports. position the receiver in the inside part using adhesive supports RAVRT011TF11/15/TFV RAVRT009TF11/15 position the receiver in the inside part using adhesive supports Figure 5 The wiring harness must be connected between the on the CPU board inside the console. receiver and the JP14 connector JP14 JP14 Figure 6 6. Positioning the SRT051BTH Kit Do not position the receiver directly on metal surfaces. In the case of the console units, remove the position this as shown below, in the inside part, using adhesive supports. RAVRT009TF11/15 RAVRT011TF11/15/TFV position the receiver in the inside part using adhesive supports position the receiver in the inside part using adhesive supports Figure 7 Page 3/6

The wiring harness must be connected between the receiver and the additional serial board code

Carefully fit the additional serial board above the CPU code 10114 and then connect the wiring

Positioning the SRT052BTH Kit Do not position the receiver directly on metal surfaces.

supports PFC 601/PFC 603 position the receiver in the inside part using adhesive supports

6 The wiring harness must be connected between the receiver and the additional serial board code Carefully fit the additional serial board above the CPU code and then connect the wiring harness in position P5NA. JP5NA Figure 8 7. Positioning the SRT052BTH Kit Do not position the receiver directly on metal surfaces. In the case of the console units, remove the position this as shown below, in the inside part, using adhesive supports. RAVRT011TF11/15/TFV RAVRT009TF11/15 position the receiver in the inside part using adhesive supports PFC 601/PFC 603 position the receiver in the inside part using adhesive supports Figure 9 The wiring harness must be connected from the receiver to the additional serial board code Use the 9-pole tray adapter/4 pole ampmoduii and connect the wiring harness in position P5N (with the adapter the port becomes P5NB). IMPORTANT: Place the bridge that supplies the P5N in low position. P5N Figure 10 Page 4/6

8. CONFIGURATION The transmitter and the receiver are associated in the factory.

See Figure 11 Same address on receiver and transmitter OFFSET GAIN Figure 11 In case of a fault affecting one of the two, both the

The transmitter is also factory set and, for this reason, during installation, the Offset and Gain parameters must be attributed.

7 8. CONFIGURATION The transmitter and the receiver are associated in the factory. On the transmitter and on the receiver, labels are shown indicating the same address (12-figure code). See Figure 11 Same address on receiver and transmitter OFFSET GAIN Figure 11 In case of a fault affecting one of the two, both the transmitter and the receiver will have to be replaced. The transmitter is also factory set and, for this reason, during installation, the Offset and Gain parameters must be attributed. These are shown on the transmitter label. To enter the OFFSET and GAIN values, proceed as follows: Press key F1 from the initial program page (Figure 12). Figure 12 Using key F2 select TECHNICAL ASSISTANCE and press the ENTER/F3 key to confirm selection (Figure 13). Figure 13 Page 5/6

Using key F2 select BTH DEVICES CONFIGURATION PARAMETERS and press the ENTER/F3 key to confirm selection (Figure 14).

confirm selection (Figure 15). The grey icons indicate that the device is not available.

Enter the OFFSET value and press ENTER/F3 again to confirm (Figure 16).

8 Using key F2 select BTH DEVICES CONFIGURATION PARAMETERS and press the ENTER/F3 key to confirm selection (Figure 14). Figure 14 Insert the following password: "F2- F2-F3-F3-F4-F4 " Using key F2 select the device to be configured and press ENTER/F3 to confirm selection (Figure 15). The grey icons indicate that the device is not available. Figure 15 Using key F2 select GAIN and press ENTER/F3 to enter the GAIN value shown on the label of transmitter (Figure 11). Enter the OFFSET value and press ENTER/F3 again to confirm (Figure 16). Using key F2 select GAIN and press ENTER/F3 to enter the GAIN value shown on the label of transmitter (Figure 11). Enter the GAIN value and press ENTER/F3 again to confirm (Figure 16). Figure 16 Press F1 to end procedure and return to initial program page. Page 6/6

Documenti analoghi

Downloading and Installing Software Socio TIS

Object: Downloading and Installing Software Socio TIS compiler: L.D. Date Revision Note April 17 th 2013 --- For SO XP; Win 7 / Vista step Operation: Image A1 Open RUN by clicking the Start button, and