BYPASS DAMPER AMM 755 2
AMM 755 VALVOLA PER FUMI A 3 VIE Campi di applicazione Fluidi: Aria, Gas e Fumi Termovalorizzatori ed Impianti d Incenerimento Cogenerazione Biomassa e Biogas Impianti di filtrazione e abbattimento polveri Centrali Elettriche Sistemi di recupero calore Caldaie e bruciatori Impianti di Ossidazione e Rigeneratori Condizioni d esercizio Massima temperatura d esercizio: 6 C Pressione massima d esercizio: 3 bar La pressione massima varia al variare del diametro e della temperatura Caratteristiche generali Servizio ONOFF o modulante Diametro da 15 a 15 (Diametri inferiori a 15 superiori a 15 su richiesta) Connessioni: FLANGIATA PN6, PN1, ANSI 15 Supporti esterni Classe di tenuta: I, II e III secondo FCI 72 (ex ANSI B16.14) Manuali e motorizzate con attuazione pneumatica o elettrica Predisposta per coibentazione esterna 2 mm Materiali Carbon Steel: S355JOWP CORTEN A (Tmax <45 C) AISI 34 AISI 316 Altri su richiesta Standard applicabili Secondo EN 125161, EN 7361, EN 7362, EN 7363, EN 1349, EN 593, ASMEB16.34 Materiali secondo EN 1531, EN 1532 Connessioni secondo EN 1921, ASME B16.5 Marcatura secondo EN 19 Certificazione Processi di saldatura UNI EN 2871 Direttive applicabili Dichiarazione di conformità alla direttiva macchine 26/42/CE Dichiarazione di conformità alla direttiva PED 97/23/CE Dichiarazione di conformità alla direttiva ATEX 94/9/CE Gruppo II Categoria 3 per Zona 2 Gas e 22 Polveri (II 3 GD) Verniciatura In accordo a PSP Cycle PS4_PHT Carbon Steel: RAL 95 HT Test In accordo a AMMtech Quality Control Plan QCP In accordo a ANSI/FCI72, EN 122661, EN 122662, EN 6534 Attuazione Attuatori pneumatici e elettrici secondo EN 157141, EN 157142, EN 157143 Connessioni e Attuatori secondo EN ISO 521, EN ISO 5211 AMM 755 BYPASS DAMPER Applications Fluids: Air, Gas and Fumes CHP and Incineration Plants Biomass, Biogas and Renewable Energy Plants Air Pollution and Filtration Power Plants Heat recovery systems Boilers and Burners Thermal Oxidizers Working Conditions Maximum Working Temperature up to 6 C Maximum Working Pressure up to 3 bar Maximum Working pressure varies with diameter and temperature General Characteristics ON/OFF or MODULATING Service Diameter Range from 15 to 15 ( below 15 or above 15 upon request) End Connections: FLANGED PN6, PN1, ANSI 15 Outside Bushing Tightness Class I, II and III according to FCI 72 (ex ANSI B16.14) Operated by Handlever, Pneumatic or Electric Actuators Designed for Insulation 2 mm Materials Carbon Steel: S355JOWP CORTEN A (Tmax < 45 C) 34 SS 316 SS others upon request Applicable Standards Designed according to EN 125161, EN 7361, EN 7362, EN 7363, EN 1349, EN 593, ASME B16.34 Materials according to EN 1531, EN 1532 End Connections as per EN 1921, ASME B16.5 Marking according to EN 19 Certified Welding Procedures according to UNI EN 2871 Applicable Directives Declaration of Conformity in Compliance with Machinery Directive 26/42/CE Declaration of Conformity in Compliance with Directive PED 97/23/CE Declaration of Conformity in Compliance with Directive ATEX 94/9/CE Group II Category 3 for Zone 2 Gas and 22 Dust (II 3 GD) Coating According to PSP Cycle PS4_PHT Carbon Steel: RAL 95 HT sylicon coating Test According to AMMtech Quality Control Plan QCP According to ANSI/FCI72, EN 122661, EN 122662, EN 6534 Driving Systems Pneumatic and Electric Actuators according to EN 157141, EN 157142, EN 157143 Actuators End Connections as per EN ISO 521, EN ISO 5211 3
Flow Coefficient Kv 15 4 FLOW COEFFICIENT Flow Coefficient KV NPS 9 8 7 6 5 4 3 2 1 15 6 1593 1322 874 56 318 197 14 46 5 2 8 2861 2458 1591 874 591 367 218 94 1 12 1 25 1 4557 3948 2492 1443 916 532 291 122 18 3 12 74 5852 3811 2235 1447 935 525 26 27 35 14 987 7597 5152 2935 187 117 66 252 31 4 16 1294 112 6792 385 2355 1525 85 353 36 45 18 14843 12436 8769 5122 332 1816 1143 454 51 5 2 19434 15691 1142 631 443 2415 1379 531 64 6 24 28355 23588 15256 927 5576 3616 214 817 155 7 28 39198 32657 2885 1227 7779 4982 2928 117 264 8 32 5111 43759 27424 1716 11344 6235 3681 163 331 9 36 65197 56692 35219 2949 1393 7812 467 198 42 1 4 88575 7431 45613 27339 17739 1979 5929 2424 576 11 44 12597 81922 5219 317 19862 1343 732 2977 629 12 48 114762 9965 61188 36818 23213 15698 8746 3339 722 13 52 129225 155 7393 4136 25674 16364 9451 472 823 14 56 148449 121954 77473 46911 27595 1748 137 558 886 15 58 186168 151348 9837 58748 36171 23234 13284 5876 1168 Kv = Qn/519 * [(ρg*t1)/( p*p2)]^,5 where: 14 8 6 4 2 1 2 15 3 4 5 6 7 Disc Posi on (opening degrees) 2 25 3 8 35 9 4 Flow Coefficient Kv 45 9 7 6 5 4 3 (Cv = Kv/,8565) 2 Qn [m3/h] : Flow Rate of gas, related to C and 113 mbar ρg [kg/m3] : density of gases at C and 113 mbar : absolute temperature at upstream side of the valve T1 [K] p [bar] : pressure drop in the valve : absolute pressure at downstream side of the valve p2 [bar] 1 1 2 45 3 4 5 6 7 Disc Posi on (opening degrees) 5 6 7 8 8 9 9 Flow Coefficient Kv 1 15 2 Nota: Il coefficiente di flusso Kv in tabella è relativo alla valvola a farfalla: per il corretto calcolo della perdita di carico occorre tenere in considerazione la perdita di carico nella derivazione e la variazione della portata dovuta alla deviazione del flusso. 18 16 Note: The flow coefficient Kv in the table is relative to the Butterfly valve: for the correct calculation of the pressure drop is necessary to consider the pressure loss of pressure in the derivation and the variation of the flow due to deflection. 14 12 AMM 755 BYPASS DAMPER 1 8 6 4 2 1 2 1 VALVE MATERIAL Body and disc material S355JOWP AISI 34 AISI 316 5 4 3 2 1 Verificare compatibilità chimica dei materiali con fluido di processo. * Chemical suitability of construction material to verified according to process fluid. 4 5 6 Disc Posi on (opening degrees) 11 12 13 7 8 14 Braid material for seat and packing 6 C 3 4 Graphite FiberGlass 9 15
LAYOUT STANDARD B B A C A B A C Flow in Flow in C Flow in CODE CODE CODE AB2C1 A1B2C A2BC1 Il codice di configurazione si compone della lettera relativa alla via, seguita dal numero che identifica il comando (come da tabella) SEAT STYLES The layout code is composed by a letter corresponding to the way, followed by a number matching the type of command (as per the below table) LAYOUT TABLE 1 2 Libera Free Attuata Actuated Condotta Accompanied COD. standard Tenuta Met / Met Metal to Metal seat CLASS VALUE (FCI 72) from 15 to 2 I Relative tightness from 25 to 15 II <,5%Kvs COD.3 Senza battuta No seat CLASS VALUE (FCI 72) from 15 to15 I Relative tightness COD.5 Tenuta potenziata con treccia Soft Sealing with Braid 5 CLASS VALUE (FCI 72) from 15 to 2 II <,5%Kvs from 25 to 1 III <,1%Kvs from 11 to 15 III/IV <,5%Kvs
BYPASS DAMPER B H F langed AMM 755 Ø Est M L E Ø int CH E1 PS MAX (bar) Ø int PN6 Ø est PN1 Le coppie fornite dagli attuatori PNEUMATICI sono state calcolate considerando una pressione d alimentazione di 5 bar. The torque values supplied by PNEUMATIC actuators are calculated assuming a supply pressure of 5 bar. B L M E E1 CH H WEIGHT Diametri inferiori a 15 o superiori a 15 su richiesta. below 15 or above 15 available upon request. Coppie senza fattore di sicurezza (per dimensionamento maggiorare del 4%). Torque without security factor (for sizing calculate additional 4%). Max Torque (Nm) Suggested Actuator 15 3 16 265 285 47 385 192 F7 F5 14 17 29 13 AM2. AM25.4 2 3 211 32 34 495 44 22 F7 F5 14 17 35 2 AM2. AM25.4 25 2 267 375 395 522 495 247 F7 F5 14 17 47 23 AM2. AM35.4 3 2 316 44 445 547 545 273 F7 F5 14 17 7 29 AM2. AM35.4 35 2 35 49 55 564 65 32 F1 F7 22 2 85 34 AM3. AM35.4 4 2 4 54 565 588 665 32 F1 F7 22 2 95 39 AM3. AM35.4 45 1 45 595 615 648 715 357 F1 F7 22 2 115 46 AM4. AM45.4 5 1 5 645 67 673 85 425 F1 F7 22 2 135 55 AM4. AM45.4 6 1 6 755 78 721 12 51 F1 F7 22 2 157 72 AM4. AM45.4 7 1 7 86 895 771 119 595 F1 F7 22 2 217 88 AM45. AM5.4 8,5 8 975 115 821 136 68 F1 F7 22 2 39 1 AM45. AM5.4 9,5 9 175 1115 963 124 62 F14 F12 27 25 398 116 AM55. AM6.4 1,5 1 1175 123 113 17 85 F14 F12 27 25 53 135 AM55. AM6.4 11,5 11 129 1335 163 187 935 F14 F12 27 25 614 161 AM55. AM6.4 12,5 12 145 1445 1113 24 12 F14 F12 27 25 745 187 AM55. AM6.4 13,2 13 1515 156 1163 221 115 F14 F12 27 25 881 218 AM6. AM65.4 14,2 14 163 1675 1215 238 119 F14 F12 27 25 135 25 AM6. AM65.4 15,2 15 173 1795 1265 255 1275 F14 F12 27 25 1258 278 AM6. AM65.4 AMMtech si riserva il diritto di apportare modifiche ai propri prodotti in qualunque momento / AMMtech reserves the right to make changes to its products at any time. 6 * * Double Acting Single Acting
Carter Carbon Steel Indicatore Meccanico ApertoChiuso Open/Close mechanical indicator Bracket Carbon Steel Viti con rondella e bullone Bolts and washer Stainless Steel Grade A2 Leva / Lever S355JOWP (Corten A) 34 SS 316 SS Tirante / Tie Rod 34 SS Acciaio / Galvanized Steel Premitreccia / Push Packing 34 SS Treccia di Tenuta Packing Braid Grafite / Graphite Fibra di vetro / Glass Fiber Bronzina / Bushing Bronzo Bronze Targhetta Name Plate Supporto / Support 316 SS Supporto Bronzina Bushing Support 34 SS Corpo / Body S355JOWP (Corten A) 34 SS 316 SS Viteria / Bolting Stainless Steel Grade A4 Albero Superiore Upper Shaft 316 SS Gasket Grafite / Graphite Fibra di vetro / Glass Fiber Gasket Grafite / Graphite Fibra di vetro / Glass Fiber Viteria / Bolting Stainless Steel Grade A4 Lente / Disc S355JOWP (Corten A) 34 SS 316 SS Albero Inferiore Lower Shaft 316 SS Targhetta Name Plate 7
AMMtech s.r.l. Via Giacomo Puccini 194/N 5516 Porcari (LU) Italy Ph. +39 583 2166 info@ammtech.it www.ammtech.it CATALOGUE EDITION N 1 segnoadv.com