MACCHINE DA CAFFE' AUTOMATICA AUTOMATIC COFFEE MACHINES DE' LONGHI ECAM 23.450 EX: 3 (INT-AU/NZ-RU-SKA-CH) DATI TECNICI / TECHNICAL DATA / TECHNISCHE DATEN DONNEES TECHNIQUES / DATOS TECNICOS Voltaggio / Voltage / Spannung / Voltage / Voltaje V / Hz 230-240 / 50-60 Max. potenza assorbita / Max. input power W 1350 SEZIONE CAFFE' / COFFEE SECTION Sonda termica / Temperature probe C 98 (Caffè / Coffee) C 98 (Acqua calda / Hot water) Fusibile termico TCO / Thermal fusetco C 192 Resistenza riscaldamento W 600 + 600 Pompa / Pump TYPE / W ULKA EP5 / 48 SEZIONE VAPORE / STEAM SECTION Sonda termica / Temperature probe C 145 (Vapore / Steam) Fusibile termico TCO / Thermal fusetco / Thermische-Sicherung TCO C 318 Fusible thermique TCO / Fusible térmico TCO Resistenza riscaldamento / Heating element / Heizelement W 1000 Elément chauffant / Resistencia de calefación 1 SCHEDA TECNICA ST1572 / 2010
SCHEMA ELETTRICO / ELECTRICAL DIAGRAM Sensore di Hall Hall sensor Sensore temperatura Caffè CoffeeTemperature Sensor Flussimetro Water flow meter Sensore Reed Reed Sensor Sensore Temp. Caldaia IFD IFD Boiler Temp. Sensor Resistenza Caffè Coffee Heating element Scheda comandi Control board Interruttore ON / OFF - ON /OFF switch Resistenza Vapore Steam Heating element Scheda filtro motore Motor Filter board Motore Gruppo infusore Infuser Group motor Elettrovalvola vapore 2 vie Steam valve 2 ways Elettrovalvola scarico 3 vie Discharge valve 3 ways Pompa / Pump Protettore Pompa Pump Thermal protector Motore Macinino Grinder Motor 2 SCHEDA TECNICA ST1572/2010
SCHEMA ELETTRICO / ELECTRICAL DIAGRAM Sensore di Hall Hall sensor Sensore temperatura Caffè CoffeeTemperature Sensor Flussimetro Water flow meter Sensore Reed Reed Sensor Sensore Temp. Caldaia IFD IFD Boiler Temp. Sensor Scheda comandi Control board Resistenza Caffè Coffee Heating element Resistenza Vapore Steam Heating element Elettrovalvola scarico 3 vie Discharge valve 3 ways Elettrovalvola vapore 2 vie Steam valve 2 ways Motore Macinino Grinder Motor Protettore Pompa Pump Thermal protector Pompa / Pump Motore Gruppo infusore Infuser Group motor Scheda filtro motore Motor Filter board Legenda colori /colors Bianco / White Blu / Blue Giallo / Yellow Grigio / Grey Marrone / Brown Nero / Black Rosso / Red Verde / Green Viola / Violet 3 SCHEDA TECNICA ST1572/2010
LOAD PROCEDURA CORRISPONDENZA TASTO CARICO EV1+EV2 HEATER CORRESPONDENCE BETWEEN GRINDER BUTTON PRESSED - ICON / LOAD Button- Icon LOAD EV1 i microswitch emettono il segnale OK Water Pump MOTOR acustico quando attivati UP/DOWN MENU PUMP UP NOTA: Rilasciare i tasti quando il motore inizia la With the machine in Standby mode, EV2 movimentazione 1 CUP Coffee boiler ON (OFF with main switch on 1), open Service door, then press and hold VAPORIZER symultaneously the 3 icons: ) CORRISPONDENZA ON / STANDBY Steam boiler ON PROCEDURA LOAD Menu, 1 CUP, Coffee Taste, till the TASTO DISPLAY message displayed is: SELECT. HOT BUTTON WATER1 EV 2 Close the door and press COFFEE LENGHT BUTTON 2 to enter the test procedure 2 CUPS EV 1 + Fan (message displayed: BUTTON 3 LOAD ). CAPPUCCINO EV 1 + EV 2 BUTTON 4 + Light DISPLAY BUTTON 5 TASTE BUTTON 6 COFFEE LENGHT BUTTON 7 BUTTON 8 Grinder L'accesso Motor al display test mode abilita il primo innesco DOWN To NOTA: exit Rilasciare the procedure, i tasti quando appare unplug il messaggio the machine or switch it OFF by the main switch. DISPLAY MANOPOLA GUSTO Incremento della barra di progresso ENCODER RESET Per poter concludere correttamente la procedura, accendere la macchina facendo erogare un risciacquo e successivamente eseguire lo spegnimento con l'interruttore generale. NOTA: Rilasciare i tasti quando lampeggiano i LED OK e ESC
LOAD Machine OFF but plugged IN. Press and hold simultaneously the following buttons, then switch the main switch on position I: CORRISPONDENCE BUTTON LOAD EV1+EV2 HEATER CORRESPONDENCE BETWEEN GRINDER BUTTON PRESSED - ICON / LOAD Button- Icon LOAD EV1 OK Water Pump MOTOR UP/DOWN MENU PUMP UP : Release the buttons after the motor With the machine in Standby mode, EV2 starts to move 1 CUP Coffee boiler ON (OFF with main switch on 1), open Service door, then press and hold VAPORIZER symultaneously the 3 icons: ) CORRISPONDENCE ON / STANDBY Steam boiler ON LOAD Menu, 1 CUP, Coffee Taste, till the BUTTON DISPLAY message displayed is: Machine OFF but plugged SELECT IN. Press. and hold HOT BUTTON WATER1 EV 2 simultaneously the following Close the buttons, door then and press switch the main switch COFFEE on position LENGHT I: BUTTON 2 to enter the test procedure 2 CUPS EV 1 + Fan (message displayed: BUTTON 3 LOAD ). CAPPUCCINO EV 1 + EV 2 BUTTON 4 + Light DISPLAY BUTTON 5 TASTE BUTTON 6 COFFEE LENGHT BUTTON 7 BUTTON 8 Grinder Entering Motor this Procedure will enable the priming of the pump DOWN : Release the buttons after the message DISPLAY is displayed Turn Coffee taste knob LED bar will lit To exit the procedure, unplug the machine or switch it OFF by the main switch. Machine OFF but plugged IN. Press and hold simultaneously the following buttons, then switch the main switch on position I: ENCODER RESET In order to complete the procedure, switch ON the machine and perform a washing cycle. After that, switch OFF the machine by the main switch : Release the buttons after the LEDs OK and ESC start flashing