1
Introduzione Powergate SL Powergate SL è la soluzione per la lettura e la programmazione tramite presa diagnosi di vetture dotate di protocollo OBDII, CAN e J1850. Powergate SL può anche essere utilizzato per la ricerca e la cancellazione degli errori presenti nella memoria dell automobile (DTC). Posizione presa diagnosi Powergate comunica con il vostro veicolo attraverso la presa diagnosi. AUDI Sotto il volante, al di sopra dei pedali. Tempo di lettura, circa 20 minuti. Tempo di scrittura, circa 10 minuti. FORD Sotto il volante, al di sopra dei pedali. Tempo di lettura, circa 5 minuti. Tempo di scrittura, circa 5 minuti. RENAULT Tunnel centrale, è necessario rimuovere il coperchio. Tempo di lettura, circa 10 minuti. Tempo di scrittura, circa 5 minuti. SEAT Sotto il volante, al di sopra dei pedali. Tempo di lettura, circa 20 minuti. Tempo di scrittura, circa 10 minuti. SKODA Sotto il volante, al di sopra dei pedali. Tempo di lettura, circa 20 minuti. Tempo di scrittura, circa 10 minuti. VW Sotto il volante, al di sopra dei pedali. Tempo di lettura, circa 20 minuti. Tempo di scrittura, circa 10 minuti. Avvertenze Ogni configurazione difforme dall originale deve essere utilizzata solo per la circolazione in circuito chiuso. Non rimuovere il connettore OBDII del vostro Powergate dal connettore diagnosi durante le varie operazioni. Spegnere i dispositivi elettrici ed elettronici installati sulla vostra vettura prima di connettere Powergate alla presa diagnostica. Spegnere il motore, rimuovere la marcia e tirare il freno a mano. Durante le operazioni di letture e/o scrittura, le ventole di raffreddamento potrebbero avviarsi. 2
Installazione Powergate SL POWERGATE SL USER GUIDE 1. Connettere il PC al sito internet www.alientech.to e scaricare il software. 2. Cliccare sul pulsante PWG CONSOLE e salvare il file proposto all interno del proprio PC. 3. Eseguire il file di installazione appena scaricato, sarete guidati durante il processo di installazione. 4. Collegare Powergate al PC tramite il cavo USB in dotazione, alla prima connessione sarà richiesto di installare i driver del dispositivo USB, contenuti nella cartella (C:\PWG CONSOLE). Come usare Powergate SL 1. Eseguire il software PWG Console. 2. Collegare Powergate al PC tramite il cavo USB in dotazione. 3. Cliccare il pulsante Link per avviare la comunicazione tra PC e il vostro Powergate SL. 4. Scegliere la vostra automobile dalla lista e attendere l installazione del firmware corretto. 5. Selezionare la lingua che sarà visualizzata sul display del vostro Powergate e attendere il completamento dell installazione. 6. Rimuovere Powergate dal connettore USB. 7. Localizzare la porta diagnostica sulla propria vettura. 8. Connettere il cavo OBDII di Powergate alla presa diagnostica. Powergate da questo momento è in funzione. 9. Scegliere Leggi file dalla ECU e seguire attentamente le istruzioni sul display di Powergate che vi guideranno alla lettura del file originale. 10. Rimuovere il cavo OBDII del vostro Powergate dalla presa diagnostica. 3
11. Collegare Powergate al PC tramite il cavo USB in dotazione. 12. Eseguire il software in dotazione. 13. Cliccare il pulsante Link per avviare la comunicazione tra PC e il vostro Powergate. 14. Cliccare sul pulsante Download ORI per scaricare il file presente in Powergate SL sul vostro pc. A questo punto, siete in possesso di un file originale codificato da inviare al vostro Master, che potrà interpretarlo, modificarlo ed inviarlo sotto forma di file codificato, pronto per la scrittura in centralina. Per effettuare la programmazione in centralina, seguire questi passaggi: 1. Eseguire il software PWG Console 2. Collegare Powergate al PC tramite il cavo USB in dotazione. 3. Cliccare sul pulsante Link 4. Cliccare sul pulsante Carica MOD 5. Selezionare il file modificato inviato dal Master 6. Terminata la procedura di upload del file modificato, scollegare Powergate SL dal PC e tornare sulla vettura. 7. Collegare Powergate SL alla presa diagnosi e selezionare la procedura di scrittura della ECU. 8. Selezionare il file da scrivere sulla centralina. 9. Terminata la procedura di programmazione, spegnere il quadro e scollegare Powergate SL dalla presa diagnosi 4
Ripristino delle condizioni iniziali di Powergate SL 1. Collegare Powergate al PC tramite il cavo USB in dotazione. 2. Eseguire il software in dotazione. 3. Cliccare il pulsante Link per avviare la comunicazione tra PC e il vostro Powergate. 4. Cliccare il pulsante Cancellazione, il vostro Powergate sarà totalmente cancellato. 5. Ripetere le operazioni descritte nel capitolo Come usare Powergate SL, a partire dal punto 4. Diagnostica Su alcuni modelli di vetture incluse nell elenco (la lista aggiornata è disponibile sul sito www.alientech.to), Powergate è in grado di effettuare la lettura della memoria errori DTC e cancellarne la presenza. La funzione di cancellazione errori è totalmente diagnostica, Powergate non risolve alcun problema presente sulla vettura. Si consiglia di rivolgersi ad un tecnico qualificato, qualora la semplice cancellazione errori, non risolvi inconvenienti temporanei. 5
Introducing Powergate SL Powergate SL is the Alientech solution to read and program by OBDII, CAN e J1850 communication protocols on all cars via diagnostic sockets. Powergate SL can also be used to search for and to delete errors that are into the car eproms. Powergate SL, or Multifamily, allows at the moment of purchase to personalize the car s list in which the user can work on, modifying it at its own needs. Powergate SL it s a real garage tool, and so it s no more necessary to reprogram the original file of the car before to rehabilitate the initial conditions. Diagnostic port location Your Powergate communicates with your vehicle via the diagnostic port. AUDI Underneath the steering wheel, above the pedal assembly. For read time allow 20 minutes. For programming time allow 10 minutes. FORD Underneath the steering wheel, above the pedal assembly. For read time allow 5 minutes. For programming time allow 5 minutes. RENAULT Under the front ashtray in the centre console on the vehicle. For read time allow 10 minutes. For programming time allow 5 minutes. SEAT Underneath the steering wheel, above the pedal assembly. For read time allow 20 minutes. For programming time allow 10 minutes. SKODA Underneath the steering wheel, above the pedal assembly. For read time allow 20 minutes. For programming time allow 10 minutes. VW Underneath the steering wheel, above the pedal assembly. For read time allow 20 minutes. For programming time allow 10 minutes. Warning Each configuration different from the original one must be used only in closed circuits. Don't remove the OBDII connector of your Powergate from the diagnosis connector during the operations. Turn off all electric and electronic devices installed on your car before to connect the Powergate to the diagnosis port. Turn off the engine, go out of gear and put on the hand brake. Throughout reading and writing operations, the fans could start. 6
Powergate SL Installation POWERGATE SL USER GUIDE 1. Connect the PC to the internet website: METTERE INDIRIZZO INTERNET 2. Click on the button Download PWG CONSOLE and save the file on your PC. 3. Execute the installation file as soon as downloaded, you will be guides to you during the installation process. 4. Connect Powergate to the PC through cable USB in equipment, to the first connection will be necessary install the driver of USB device, contained in the folder (C:\PWGCONSOLE). How to use Powergate SL 1. Run PWG Console software. 2. Connect Powergate unit to PC via USB cable. 3. Click the button Connection to start the communication between PC and your Powergate SL. 4. Choose your specific-car from the list and wait for the installation of the correct firmware. 5. Choose the language that will be shown on the display of yours Powergate and wait the installation of the language. 6. Remove the Powergate unit from USB connector. 7. Locate the diagnostic port in your vehicle. 8. Connect the Powergate s OBDII cable to the diagnostic port. Powergate from this moment is active. 9. Choose Read ECU File and follow the instruction on the display of the Powergate that help you in the reading of the original file. 10. Remove the OBDII cable on your Powergate from the diagnostic port. 11. Connect Powergate unit to PC via USB cable. 7
12. Run PWGPro software. 13. Click the button Connection to start the communication between PC and your Powergate Unit. 14. Click on the button Download ORI to download the file that is into the Powergate SL on your PC. At this point, you are in possess of an original file codified ready to be sent to your own Powergate Master, that will be able to interpret it, modify it and send it to the Ecu like a codified file ready to the writing. To make the programmation in the Ecu, follows the steps below: 1. Run PWG Console software 2. Connect Powergate unit to PC via USB cable. 3. Click the button Connection 4. Click the button Download MOD 5. Select the modified file sent to the Powergate Master 6. When the upload procedure of modified file is finished, disconnect Powergate SL from PC and return on the car. 7. Connect Powergate SL to the diagnostic port and select Ecu writing procedure. 8. Select the file to be wrote on the ECU. 9. When the programmation procedure is finished, turn off board and disconnect Powergate SL from diagnostic port. 8
Restoring starting conditions of Powergate SL POWERGATE SL USER GUIDE 1. Connect Powergate to the PC by USB cable you find in the kit. 2. Install the software. 3. Click on Connection button to start the communication between the PC and your Powergate. 4. Click on Erase button, and your Powergate will be totally cancelled/erased. 5. Repeat the steps mentioned in the instruction called How to use Powergate M, starting from step 4. Diagnostics On some of the car models listed (the update list is available on our website www.alientech.to), Powergate can read the DTC errors memory and delete it. The errors deleting function is diagnostics, Powergate doesn't solve any defect of the car. We advise you to ask to a qualified technician if the errors erasing don't solve temporary problems. 9
Dichiarazione di conformità Noi, Via dei Cordari 1, 13039 Trino (VC), ITALIA Il costruttore dichiara che il prodotto: Prodotto Powergate è conforme alle seguenti Direttive: EMC 89/336/EEC Marcatura CD 93/68/CE ed alle seguenti Norme Armonizzate: EMC: EN 55022 : 1998 + A1 : 2000 + A2 : 2003 EN 55024 : 1998 + A1 : 2001 + A2 : 2003 Piermichele Mortarino Via dei Cordari 1, 13039 Trino (VC), ITALIA 10
Alientech s.r.l. Sede Operativa 13039 Trino (VC) - Italy Via Dei Cordari, 1 tel: (+39) 0161 801025 fax: (+39) 0161 828967 Per maggiori informazioni www.alientech.to infoservice@alientech.to 11