C94/60-T C94/60-TN SPEAKER SYSTEMS MANUALE DI ISTRUZIONI OPERATING MANUAL

Dimensione: px

Iniziare la visualizzazioe della pagina:

Download "C94/60-T C94/60-TN SPEAKER SYSTEMS MANUALE DI ISTRUZIONI OPERATING MANUAL"

Jacopo Franchini
6 anni fa
Visualizzazioni

1 C94/60-T C94/60-TN SPEAKER SYSTEMS MANUALE DI ISTRUZIONI OPERATING MANUAL

2 C94/60-T (60W - bianco) C94/60-TN (60W - nero) C94/60-T (60W - white) C94/60-TN (60W - black) Questo prodotto è conforme alle Direttive della Comunità Europea sotto le quali lo stesso ricade. This product is in keeping with the relevant European Community Directives.

COLLEGAMENTI CONNECTIONS C94/60-T The speaker ca be connected to audio lines at constant voltage (100V / 70V) or with constant impedance (switch set at 8 Ohm).

Connect amplifier s positive conductor (output 100V/70V or + ) to the + of the connector (A).

CONSTANT VOLTAGE SYSTEMS The input voltage selected on the speaker must correspond to the voltage selected on the amplifier output.

3 COLLEGAMENTI CONNECTIONS C94/60-T The speaker ca be connected to audio lines at constant voltage (100V / 70V) or with constant impedance (switch set at 8 Ohm). Connect the negative conductor from amplifier s output ( 0'/ COM / - ) to the - of speaker input connector (A). Connect amplifier s positive conductor (output 100V/70V or + ) to the + of the connector (A). A speaker can be used both in constant voltage sound systems and constat impedance systems. CONSTANT VOLTAGE SYSTEMS The input voltage selected on the speaker must correspond to the voltage selected on the amplifier output. The sum of the nominal power values of all the connected speakers must not exceed that of the amplifier. CONSTANT IMPEDANCE SYSTEMS The total load impedance of all the connected speakers must be no less than the impedance selected on the amplifier output, to avoid the risk of serious damage to the amplifier. The sum of nominal power values of all connected speakers must be no less than that of the amplifier. Connection cable lengths must be kept to the indispensable minimum.

4 COLLEGAMENTI CONNECTIONS SPEAKER S CONNECTION TO A CONSTANT VOLTAGE SYSTEM This connection system implies that each speaker is equipped with its own line transformer. The ampliifer shall be equipped with 100V / 70V constant voltage outputs. The loudspeakers connected in parallel to amplifier s output will make system expansion easier, if required, by simply shunting from any of the previously installed speakers. Similarly, the loudspeakers which are not necessary anymore can be removed. Matching the phase is necessary both in the connection of each speaker to its own transformer and in the connection in parallel of the speakers. All the constant voltage outputs (100V / 70V) of a single amplifire can be connected at the same time, provided that amplifier s rated power remains equal or higher to the sum of the power of all the speakers installed on each output line. P = V 2 / Z Z = V 2 / P 2 Using the following formula: P = V /Z with V being 100V / 70V and Z being speaker s transformer primary impedance - any power applied to each speaker can be calculated. If, instead, you know the voltage (100V / 70V) and the rated power (or powers) of the transformer and you want to calculate transformer impedance, the 2 following formula applies: Z = V / P SPEAKER S CONNECTION TO A CONSTANT IMPEDANCE Constant impedance outputs are generally used in the case of line with a small number of speakers having a certain power and being placed at a minimum distance from the amplifier. Seakers connection will be a combination of connection in parallel and series connection, so to bring loudspeakers total impedance to a value which is not critical for the amplifier. In the series connection the positive lug shall be connected to the negative lug of the following speaker. In the connection with constant impedance it is always recommended that speakers total power is higher than the power supplied by the amplifier. If in the connection with constant impedance the volume of one or more speakers needed to be set independently or also if any speaker needed to be switched off, the use of attenuators keeping impedance constant is required. In the series connection, whatever the impedance of each speaker, the total impedance results from the sum of all the impedances. Anyway, using sound speakers with equal impedance and power is recommended. 3

5 INSTALLAZIONE INSTALLATION WHEN THE SPEAKER IS MOUNTED ON THE WALL, THE SYSTEM MUST BE EQUIPPED WITH THE SAFETY CABLE (PROVIDED) IN ORDER TO AVOID DAMAGES TO PEOPLE OR PROPERTY. CAREFULLY CHOOSE THE AREA WHERE SPEAKERS WILL BE INSTALLED, MAKING SURE THAT THE STRUCTURE CAN SUPPORT SPEAKERS S WEIGHT. Remove the wall support from the speake through the threaded insert B. Insert the cable in the hole C and connect to a euroblock connector (E). Fix also the protection cable D.

6 INSTALLAZIONE INSTALLATION Secure the wall support through the four holes F Put the speaker in the wall support, and secure the other end of the safety cable (G) and the euroblock connector (E). G E

7 INSTALLAZIONE INSTALLATION Point the speaker as desired Avvertenze per lo smaltimento del prodotto ai sensi della Direttiva Europea 2002/96/EC. Alla fine della sua vita utile il prodotto non deve essere smaltito insieme ai rifiuti urbani, ma deve essere consegnato presso gli appositi centri di raccolta differenziata predisposti dalle amministrazioni comunali, oppure presso i rivenditori che forniscono questo servizio. Smaltire separatamente un rifiuto elettrico e/o elettronico (RAEE) consente di evitare possibili conseguenze negative per l ambiente e per la salute derivanti da un suo smaltimento inadeguato e permette di recuperare i materiali di cui è composto al fine di ottenere un importante risparmio di energia e di risorse. Su ciascun prodotto è riportato a questo scopo il marchio del contenitore di spazzatura barrato. Important information for correct disposal of the product in accordance with EC Directive 2002/96/EC. This product must not be disposed of as urban waste at the end of its working life. It must be taken to a special waste collection centre licensed by the local authorities or to a dealer providing this service. Separate disposal of electric and/or electronic equipment (WEEE) will avoid possible negative consequences for the environment and for health resulting from inappropriate disposal, and will enable the constituent materials to be recovered, with significant savings in energy and resources. As a reminder of the need to dispose of this equipment separately, the product is marked with a crossed-out wheeled dustbin.

8 DATI TECNICI / TECHNICAL DATA CONFIGURAZIONE TYPE AMPLIFICATORE CONSIGLIATO RECOMMENDED AMPLIFIER POTENZA LUNGO TERMINE LONG TERM POWER POTENZA BREVE TERMINE SHORT TERM POWER vie / way W RMS W W C94/60-T C94/60-TN UDT - Ed. 06/15-11/767 TRASFORMATORE DI LINEA (100V) LINE TRANSFORMER (100V) IMPEDENZA NOMINALE RATED IMPEDANCE RISPOSTA IN FREQUENZA FREQUENCY RESPONSE UNITÀ BASSE FREQUENZE LOW FREQUENCY WOOFER W mm Hz - 20kHz 165 TWEETER SENSIBILITÀ (@1W, 1m) SENSITIVITY (@1W, 1m) SPL MAX. MAX. SPL DISPERSIONE DISPERSION DIMENSIONI DIMENSIONS PESO NETTO NET WEIGHT COLORE COLOR FILTRO HP CONSIGLIATO RECOMMENDED HP FILTER CONNETTORE DI INGRESSO INPUT CONNECTOR GARANZIA mm 257 db db O x V H x V mm Questo prodotto è garantito esente da difetti nelle sue materie prime e nel suo montaggio; il periodo di garanzia è regolamentato dalle norme vigenti. La Paso riparerà gratuitamente il prodotto difettoso qui garantito se il difetto risulterà essersi verificato durante l uso normale; la garanzia non si estende quindi a prodotti usati ed installati in modo errato, danneggiati meccanicamente, danneggiati da liquidi o da agenti atmosferici. Il prodotto, risultato difettoso, dovrà essere inviato alla Paso franco di spese di spedizione e ritorno. Questa garanzia non ne comprende altre, esplicite od implicite, e non comprende danni o incidenti conseguenti a persone o cose. Contattare i distributori PASO della zona per maggiori informazioni sulla garanzia. Importante! L utente ha la responsabilità di produrre una prova d acquisto (fattura o ricevuta) se vuole servirsi dell assistenza coperta da garanzia. Dovrà inoltre fornire data di acquisto, modello e numero di serie riportati sull apparecchio. kg BIANCO WHITE x x 312 x 219 4,5 40Hz - 24dB/oct. Euroblock WARRANTY NERO BLACK This product is warranted to be free from defects in raw materials and assembly. The warranty period is governed by the applicable provisions of law. Paso will repair the product covered by this warranty free of charge if it is faulty, provided the defect has occurred during normal use. The warranty does not cover products that are improperly used or installed, mechanically damaged or damaged by liquids or the weather. If the product is found to be faulty, it must be sent to Paso free of charges for shipment and return. This warranty does not include any others, either explicit or implicit, and does not cover consequential damage to property or personal injury. For further information concerning the warranty contact your local PASO distributor. Important! Should the user wish to avail himself of servicing under the warranty, he must provide evidence of the purchase (invoice or receipt). The user shall also indicate the date of purchase, model and serial number indicated on the equipment. Via Settembrini, Lainate (MI) - ITALIA info@paso.it

Documenti analoghi

ERGO ERGO. Istruzioni per il cablaggio Wiring instructions. // Istruzioni per il montaggio // Assembly instructions

ERGO ERGO. Istruzioni per il cablaggio Wiring instructions. // Istruzioni per il montaggio // Assembly instructions ERGO Istruzioni per il cablaggio Wiring instructions 64W ON/OFF MARRONE / BROWN - Linea / line GIALLO-VERDE / YELLOW-GREEN - Terra / Earth ERGO 65 BLU / BLUE - Neutro / Neutral // Istruzioni per il montaggio